Reviews Suspension Bushing Removal Tool Set

OTC 4245 Freightliner Rear Suspension Bushing Master Tool Set with Air/Hydraulic Pump

  • OTC's Freightliner Rear Suspension Tool Master Set features a robust 15-Ton capacity cylinder, Air/Hydraulic pump, and installation/removal adapters.
  • Removes and installs single-wrapped FAS II Airliner Freightliner Rear Suspension Bushings 'on vehicle' - no need to remove the spring assemblies to use this tool.
  • Completes the job in a fraction of the time that traditional methods take.
  • Saves an average of 45 minutes per bushing (4 per vehicle) on flat rate of 1.5 hours per bushing - a huge time savings.
  • No more hammering prevents impact damage to suspension components while dramatically reducing the effort required by the technician performing the work.
Check Stock

bimiti Rear Suspension Control Arm Trailing Arm Bushing Tool Removal Tool Kit for Ford Focus Mazda Volvo Bushing Press Kit

  • 【Application】This rear suspension bushing removal tool has a wide range of application and strong practicality. It is suitable for Ford Focus MK1 & MKII 1998-2007, Ford Cuga 2008, Ford C-Max 2007, Mazda 3 sedan, hatchback 2003-2008, suitable for Mazda 5 CR, CW, MPV 2005, applicable to V50 2004-2012, applicable to S40 MK sedan 2003-2012..
  • 【Performance】This rear suspension bushing kit has excellent performance, protects your car from scratches, no marks or scratches, and is used to silently press in and pull out the rear of the shaft to improve safety and reliability..
  • 【Easy to use】Designed for the removal and installation of bushes and bearings, this rear trailing arm bushing tool is easy to use and install without the need to remove the rear axle, saving a lot of time..
  • 【Material】This control arm bushing removal tool is made of selected carbon steel. The greater the hardness, the higher the strength, but the lower the plasticity, the stronger the rust prevention, the longer the durability and the longer the service life..
  • 【After-sales Service】This rear control arm bushing kit has been strictly tested before leaving the factory.If you encounter any problems in the use process, please contact our customer service in time, and we wil....
Check Stock

OTC 4244 Freightliner Rear Suspension Bushing Tool

  • OTC's Freightliner Rear Suspension Tool features a robust 15-Ton capacity cylinder and installation/removal adapters.
  • Removes and installs single-wrapped FAS II Airliner Freightliner Rear Suspension Bushings 'on vehicle' - no need to remove the spring assemblies to use this tool.
  • Completes the job in a fraction of the time that traditional methods take.
  • Saves an average of 45 minutes per bushing (4 per vehicle) on flat rate of 1.5 hours per bushing - a huge time savings.
  • No more hammering prevents impact damage to suspension components while dramatically reducing the effort required by the technician performing the work.
Check Stock

ABN Extra Large Ball Joint Press Kit Wheel Bearing Press Kit - Universal Ball Joint Separator Tool and Removal Adapters

  • [Easily Service Your Vehicle]: Keep your suspension system running smoothly by replacing worn or rusted ball joints with the ABN Ball Joint Removal Tool Set.
  • Use as ball joint puller kit, control arm bushing tools, U joint press kit, or tie rod and track pin press set.
  • [Fits Your Project]: Ball joint press kit heavy duty 4x4 U joint removal tool kit fits most 2 and 4 wheel-drive domestic and imported cars, pickup trucks, and SUVs with press-fit type ball joints.
  • Ball joint compressor control arm bushing press kit may even fit your tractor.
  • [Built To Last]: Professional-grade forged steel provides maximum strength and durability while the black oxide finish resists elemental damage and wear.
  • Ball joint kit will endure years of heavy use.
  • [Contents]: 11.5-inch (29.2cm) tall extra large ball joint press tool C-frame has 2 interchangeable pressure screws and a 3.5-inch (8.9cm) pressure screw head adapter.
  • Two 3-inch (7.6cm) wide stepped automotive press adapters fit the 10 and 6.5-inch (25.4 and 16.5cm) pressure screws.
  • [Convenient Storage]: 14.5 by 10.3-inch (36.8 x 26.2cm) plastic bl....
Check Stock

DEF Door Bushing Removal Tool Hinge Liners for Wrangler JK JKU JL JLU Gladiator JT 2007-2021 (Removal Tool and 2 Pins)

  • Fit: Door Bushing Removal Tool for Wrangler JK JL 4 Door 2008-2019 ..
  • Material: Made of stainless steel, great performance and repeated use are guaranteed. High quality bushings never rust .The inserts are made of plastic..
  • Function: These door pin guides help you line up your door pins and put your doors back easily. The door bushing removal tool helps to disassemble your Wrangler corrosive hinges..
  • Usage: By using the door pin guides align the top cap and lower the door so that the bottom is in place. By using a hammer, to tap the door bushing removal tool until the OE liners are totally disassembled. If you find that it is not suitable for your car，use some type of grease or lube for the new bushings and use a rubber mallet to get them in place. Maybe it works well..
  • Package include: 1 silver door bushing removal tool, 8 bushings and 2 Pins.Door Bushing Removal Tool did not fit TJ.
Check Stock

PIILOO Door Pin Guides & Door Hinge Liners & Door Bushing Removal Tool Compatible with Jeep Wrangler JK JKU JL JLU Sports Sahara Freedom Rubicon Unlimited Gladiator JT 2/4-Door 2007-2021 (17 PCS)

  • FITMENT--Perfectly compatible with Jeep Wrangler JK, JKU, JL, JLU, Sports, Sahara, Freedom, Rubicon, Unlimited, Gladiator, JT 2-Door and 4-Door 2007-2021. (NOTE: DOOR BUSHING REMOVAL TOOL DID NOT FIT TJ).
  • FUNCTION--This set of tool help you line up the door pin against the hinge and easily put the door back in place. Remove the corroded and worn door hinge liners and replace the new liners which are rust and corrosion resistance..
  • MATERIAL--The door pin guides are constructed with advanced CNC machined stainless steel, durability and never rust. The door hinge liners are made of high grade ABS plastic, anti-deformation and anti corrosion. The door bushing removal tool is made of aircraft grade integral iron structure, good rigidity, high precision and longer service life..
  • EASY INSTALLATION--Use the door pin guide to align the top cap and lower the door, so that the bottom is in place. Hit the door bushing removal tool with a hammer until the liner is completely removed. Install these while replacing the hinge liners and repairing the hinge bolts..
Check Stock

Door Pin Guides Hinge Liners and Door Bushing Removal Tool Kits (8 Door Pin Guides) 17Pcs For 2007-2020 Jeep Wrangler JK JKU JL JLU

  • DURABLE MATERIA:The Door Bushing Removal Tool was constructed with strong iron.Advanced CNC machined aircraft grade stainless steel structure guides and durable ABS plastic integral molding process bushings, anti-corrosion and never rust..
  • FITMENT:Fit for Jeep Wrangler JK, JKU, JL, JLU, Sports, Sahara, Freedom, Rubicon, Unlimited 2007-2020. (Door Bushing Removal Tool did not fit TJ).
  • WIDELY USEFUL:These door pin guides help you line up your door pins and put your doors back easily.The door bushing removal tool helps to remove your Jeep corrosive hinges.By using the door pin guides align the top cap and lower the door so that the bottom is in place. By using a hammer, to tap the door bushing removal tool until the OE liners are totally removed..
  • QUANTITY INCLUDED:8*Door Pin Guides,8*Door Hinge Liners,1*Door Bushing Removal Tool..
  • 100% SATISFACTION:If you are not satisfied with our kit,please contact us,we will try our best to solve your problem..
Check Stock

Orion Motor Tech 21PCS Master Ball Joint Press | Upper and Lower Ball Joint Removal Tool | Automotive Mechanic Tool Set

  • ESSENTIAL TOOL FOR BALL JOINT SERVICE - Use the ORION MOTOR TECH 22PCS Ball Joint Press Set Ball Joint Tool / Bushing Removal Tool with multi-size adapter to effortlessly remove press fit parts including ball joints, U-joints, brake anchor pins, and more on most 2-wheel drive (2WD) and 4-wheel drive (4WD) vehicles without removing the control arm from the vehicle..
  • UNIVERSALLY COMPATIBLE WITH A WIDE RANGE OF VEHICLES - Use the ORION MOTOR TECH Ball Joint Press Set Ball Joint Tool / Bushing Removal Tool with all the receiver tubes and removing/installing adapters needed to effortlessly remove press fit parts including ball joints, U-joints, brake anchor pins, and more on most GM, Chevy, Ford, and Dodge 2 and 4 wheel drive pickups, vans and sport utility vehicles, will service perfect for vehicles having the Dana 28, 30, 35, 44, 60 axle.
  • PROFESSIONAL GRADE QUALITY AND DURABILITY - Off road weekend warriors, novices, and professional mechanics trust the ORION kit because ORION MOTOR TECH sources the highest quality components from around the world. Constructed from heavy-duty forged solid carbon steel with anti-rust black-oxide finish on adapters for maximum strength and longevity that resists rust and corrosion..
  • CONVENIENTLY ORGANIZED IN CUSTOM MOLD....
Check Stock

Kentrol Hinge Liners (4 Door) 70002, Black

  • FIT: Door Hinge Liners for 2007-2018 Jeep Wrangler JK 4 door. Made specifically to use with OE door hinges..
  • an extremely durable low friction plastic. Maintenance free.
  • FUNCTION: These door hinge liners make the door removal job so simple. Your doors will open and close smoother than ever..
  • TO USE: Remove your doors, use the included door bushing removal tool and a hammer to remove the factory bushings. Then, slide in your new Kentrol Door Hinge Liners. Reinstall your doors and watch in surprise as your doors move back and forth seamlessly..
  • PACKAGE INCLUDES: 8 door hinge liners, 1 door bushing removal tool.
Check Stock

OTC Tools 4247 Hendrickson Suspension Bushing Master Tool Kit

  • Reduces service time to remove and install HD rear suspension bushings substantially.
  • Works on Hendrickson Primaax EX, Comfort Air and FCCC V-Ride Pivot and D-Pin suspension bushings.
  • Tool mounts to suspension for less weight to hold.
  • Tool includes adapters to align it to bushing axis to reduce likelihood of improper installation.
  • Includes a high-force 25-ton cylinder for hard-to-remove bushings and also includes the OTC Stinger Series 2510A Air/Hydraulic Pump, with a Hose and Coupler.
Check Stock

Hooke Road JK Wrangler Door Hinge Bushing Liners Replacement & Metal Door Bushing Removal Tool Compatible with Jeep Wrangler JK & Unlimited 2007-2018 - 8Pcs

  • FITMENT: Hooke Road Door Hinge Bushings Replacement Compatible with Jeep JK & Wrangler Unlimited 2007 2008 2009 2010 2011 2012 2013 2014 2015 2016 2017 2018.
  • FUNCTION: Restores proper door alignment, snug fit while allowing your doors to open and shut smoothly. The door bushing removal tool helps to remove your Jk corrosive hinges. It will prevent hinge scratches during door removal..
  • MATERIAL: The door bushing removal tool and hinge liners were constructed with mixed metal, great performance and repeated use are guaranteed..
  • INSTALLATION: Install these while replacing the hinge liners and refinishing the hinge bolts. Align top cap then proceed to let door down and the bottom will fall into place..
  • PACKAGE CONTENTS: Includes 8 Door Hing Bushings, 1 Removal Tool, and 2 Sand Paper..
Check Stock

Tiger Tool Pin and Bushing Starter Kit Without Hydraulic Cylinder for Commercial Trucks, for use with Class 6-8 Transportation Trucks and Equipment, 15099

  • This Starter Kit allows you to use any one of the Pin & Bushing Adapters to service both rubber-isolated and threaded pins and bushings - all while the suspension remains on the vehicle. Please Note: The 15099 does not include any necessary Adapters required to operate, all adapters are sold separately..
  • Application: Commonly found on class 6-8 transportation trucks and equipment. (For use with Kenworth, for use with Peterbilt, for use with Freightliner, for use with Mack, for use with Volvo, etc.).
  • There is no need to handle or remove heavy suspension assemblies. The removal of the spring packs from the axle is no longer required and this kit has 20 tons of pulling power for efficient pin removal and installation..
  • The 15099 Pin & Bushing Starter Kit, with one or more adapters, eliminates time-consuming, labor-intensive and costly processes.
  • technicians are no longer required to remove the suspension, haul it to the shop press or reassemble it to the vehicle. This system reduces shop time by as much as 70%! With more than 20 different adapter kits to choose from, and new ones being developed all the time, there sim....
Check Stock

E-cowlboy T-0220-39 Master Bushing Driver Set for Chrysler GM Ford Transmissions Bushing Bearing Seal Installer Remover Tool Kit (39 PCS)

  • 【Application】The custom bushing driver tool set is suitable for installing or removing wheel bearings, bushings, sealing rings and rubber. The tool is impact resistant and can be used with hydraulic presses and hammers..
  • 【Interchangeable】All 50 discs of the bush bearing and seal driver kit are interchangeable with each other and you can get 2,450 different size variations for quick work..
  • 【Quality Material】The bush removal puller bearing press tool is made of high-quality forged steel with a black anodized coating on the surface, effectively preventing rust and greatly extending the service life of the tool..
  • 【Custom Tool】8-65mm & 74mm metric discs. Each disc is marked with a scale for easy identification and reference. All metric discs, shafts, Allen keys, and screws remove or install bushings that are flush with the housing, allowing you to build your own custom bushing driver so that you always have the correct size for job..
  • 【Set Includes】The transmission wheel axle bearing seal installer kit includes: 48pcs*discs (18mm to 65mm with 1mm graduation) +1pc*disc (74mm) +1pc* handle/shaft +1pc*Allen wrench (3mm) +1pc*screw +1pc*storage box..
Check Stock