Reviews Vertical Shaft

Karcher 9.120-021.0 Axial Pressure Washer Pump 2.5GPM 3000PSI 3/4 Horizontal Shaft

  • Common Bolt Pattern For GC & GX Engines With 3/4" Shaft.
Check Stock

Martin SH 1 Quick Disconnect Bushing, Sintered Steel, Inch, 1\ Bore, 1.871\ OD, 1.31\ Length

  • Quick disconnect bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
  • Split through flange and taper to provide strong clamping on the shaft.
  • Sintered steel for greater strength and resistance to wear than steel.
  • Keyed to the shaft to prevent the shaft from rotating in the bushing.
  • Set screw over keyway to help keep key in place on vertical shafts and with vibrating loads.
Check Stock

Martin JA 1 Quick Disconnect Bushing, Sintered Steel, Inch, 1\ Bore, 1.375\ OD, 1.06\ Length

  • Quick disconnect bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
  • Split through flange and taper to provide strong clamping on the shaft.
  • Sintered steel for greater strength and resistance to wear than steel.
  • Keyed to the shaft to prevent the shaft from rotating in the bushing.
  • Set screw over keyway to help keep key in place on vertical shafts and with vibrating loads.
Check Stock

The Bundling Off L116T Light and 2m ac Adapter

  • 2800 psi 2.5 gpm Universal Power Pressure Washer Water Pump 308653052 for Homelite.
  • Specs - Maximum Pressure: 2800 PSI. Maximum Flow: 2.3 GPM. Maximum Pump Speed: 3400 RPM. Shaft Diameter: 7/8" Shaft. 3 Bolt Pattern: 7 11/16” x 6....
  • Includes - (1) Vertical Pressure Washer Pump with Chemical Injector, Unloader Valve, Thermal Release Valve & Outlet Tube.
  • This pump mounts vertical and is a rear facing (water inlets/outlets come out of the rear of the engine). Pump needs at least 5.5HP to handle PSI.....
  • This pump may require 1/2" spacers when installed, depending on motor configuration. Spacers are used in the case that the pump arm(s) hits the engine....
Check Stock

Martin SDS 2 Quick Disconnect Bushing, Ductile Iron, Inch, 2\ Bore, 2.187\ OD, 1.37\ Length

  • Quick disconnect bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
  • Split through flange and taper to provide strong clamping on the shaft.
  • Ductile iron for greater strength than gray cast iron and resistance to wear, galling, and corrosion.
  • Keyed to the shaft to prevent the shaft from rotating in the bushing.
  • Set screw over keyway to help keep key in place on vertical shafts and with vibrating loads.
Check Stock

Martin JA 7/16 Quick Disconnect Bushing, Sintered Steel, Inch, 0.43\ Bore, 1.375\ OD, 1.06\ Length

  • Quick disconnect bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
  • Split through flange and taper to provide strong clamping on the shaft.
  • Sintered steel for greater strength and resistance to wear than steel.
  • Keyed to the shaft to prevent the shaft from rotating in the bushing.
  • Set screw over keyway to help keep key in place on vertical shafts and with vibrating loads.
Check Stock

Martin SK 7/8 Quick Disconnect Bushing, Sintered Steel, Inch, 0.87\ Bore, 2.812\ OD, 1.93\ Length

  • Quick disconnect bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
  • Split through flange and taper to provide strong clamping on the shaft.
  • Sintered steel for greater strength and resistance to wear than steel.
  • Keyed to the shaft to prevent the shaft from rotating in the bushing.
  • Set screw over keyway to help keep key in place on vertical shafts and with vibrating loads.
Check Stock

Martin SDS 1 1/8 Quick Disconnect Bushing, Sintered Steel, Inch, 1.13\ Bore, 2.187\ OD, 1.37\ Length

  • Quick disconnect bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
  • Split through flange and taper to provide strong clamping on the shaft.
  • Sintered steel for greater strength and resistance to wear than steel.
  • Keyed to the shaft to prevent the shaft from rotating in the bushing.
  • Set screw over keyway to help keep key in place on vertical shafts and with vibrating loads.
Check Stock

Martin SF 1 7/16 Quick Disconnect Bushing, Sintered Steel, Inch, 1.44\ Bore, 3.125\ OD, 2.06\ Length

  • Quick disconnect bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
  • Split through flange and taper to provide strong clamping on the shaft.
  • Sintered steel for greater strength and resistance to wear than steel.
  • Keyed to the shaft to prevent the shaft from rotating in the bushing.
  • Set screw over keyway to help keep key in place on vertical shafts and with vibrating loads.
Check Stock

Martin SK 2 1/2 Quick Disconnect Bushing, Ductile Iron, Inch, 2.5\ Bore, 2.812\ OD, 1.93\ Length

  • Quick disconnect bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
  • Split through flange and taper to provide strong clamping on the shaft.
  • Ductile iron for greater strength than gray cast iron and resistance to wear, galling, and corrosion.
  • Keyed to the shaft to prevent the shaft from rotating in the bushing.
  • Set screw over keyway to help keep key in place on vertical shafts and with vibrating loads.
Check Stock

Martin SDS 1 Quick Disconnect Bushing, Class 30 Gray Cast Iron, Inch, 1\ Bore, 2.187\ OD, 1.37\ Length

  • Quick disconnect bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
  • Split through flange and taper to provide strong clamping on the shaft.
  • Class 30 gray cast iron for resistance to wear, galling, and corrosion.
  • Keyed to the shaft to prevent the shaft from rotating in the bushing.
  • Set screw over keyway to help keep key in place on vertical shafts and with vibrating loads.
Check Stock

Martin E 1 Quick Disconnect Bushing, Class 30 Gray Cast Iron, Inch, 1\ Bore, 3.834\ OD, 2.62\ Length

  • Quick disconnect bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
  • Split through flange and taper to provide strong clamping on the shaft.
  • Class 30 gray cast iron for resistance to wear, galling, and corrosion.
  • Keyed to the shaft to prevent the shaft from rotating in the bushing.
  • Set screw over keyway to help keep key in place on vertical shafts and with vibrating loads.
Check Stock

YAMATIC 7/8\ Shaft Vertical Pressure Washer Pump - Max 3100 PSI @ 2.5 GPM OEM & Replacement Pump for Power Washer Compatible with Honda, Ryobi, Simpson, Craftsman Homelite and More

  • OEM replacement pump for your pressure washer: Fit most 7/8" shaft vertical gas pressure washer engines. Compatible for Craftsman, Subaru, Homelite, Ryobi, Honda, Husky and more. This easy-to-install kit is great for power washers that can support up to 3000 PSI at 2.5 GPM to wash cars, sidewalks, fences, vehicles, and more..
  • Easy start & maintenance-free: This pump pre-fill oil for lifetime, so you never have to change the oil. It is also manufactured from fully die-cast aluminum for good against corrosion. If the pressure washer is not used for a long time, we recommend that you uses a anti-freeze and lubricant formula, for use before extended storage and prior to startup the following season to keep your pump running on full blast..
  • Easy installation: This replacement pump features a threaded M22 connection pressure washer hose outlet, 3/4'' NH garden hose inlet. The standard bolt pattern fits most 7/8'' vertical shaft gas-powered pressure washers. Packet includes a chemical hose with filter, mounting bolts, shaft key, and instruction booklet to get your pressure washer back in life within 10 minutes. (*Fit 7/8'' vertical shaft engines ONLY).
  • A high-quality thermal relief valve is matters: It protects the pump from overheating while in bypa....
Check Stock