Reviews Stepper Motor Arduino With Driver

3D Printer Controller Kit RepRap RAMPS 1.4 + 2560 Board + 5pcs A4988 Stepper Motor Driver with Heatsink + LCD 12864 Graphic Smart Display 3D Printer Controller Kit

  • 2560 control board: The board is a microcontroller board based on the 16AU .It has 54 digital input/output pins (of which 14 can be used as PWM....
  • RAMPS 1.4: RAMPS interfaces an for Arduino with the powerful for Arduino platform and has plenty room for expansion. The modular design includes plug....
  • LCD 12864 with Controller: This full graphic Smart Controller contains a SD-Card reader, an rotary encoder and a 128 x 64 dot matrix LCD display. You....
  • A4988 driver module: A4988 Stepper Motor Driver Board is a breakout board for Allegro?ˉs A4988 DMOS Microstepping Driver with Translator and....
  • Warning: Connecting or disconnecting a stepper motor while the driver is powered can destroy the driver. (More generally, rewiring anything while it....
Check Stock

KOOKYE 2 x 28BYJ-48 DC 5V Stepper Motor + ULN2003 Driver Test Module Board for Arduino Raspberry Pi

  • This is a stepper motor and a stepper motor driver..
  • Mainly used in air conditioner louver, small cooling and heating fan etc. Stable and all technic parameters are qualified for national electronic....
  • On-board ULN2003A chipset,On-board 4-way indicator light,On-board XH-5P socket,Compatible with Arduino..
Check Stock

MELIFE 5Pack L298N Stepper Motor Driver Controller Board Dual H Bridge Module for Arduino Smart Car Power UNO MEGA R3 Mega2560

  • Main driver chip L298N, strong driving ability, strong anti-interference, low calorific value, afterflow diode protection, more stable and reliable for Arduino projects.
  • Double H bridge design, can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors, high efficient.
  • No assembly required. This L298N board comes ready to go. Just wire up motors and power, easy to use.
  • External size 43*43*27mm / 1.69*1.69*1.06 inch, voltage 5V-35V, drive current 2A (Max single bridge).
  • Great for Arduino DIY Smart Car Robot Power UNO MEGA R3 Mega2560 Duemilanove. If driving voltage is more than 12V, please use external standard 5volt TTL outputs to switch the H-bridge circuits.
Check Stock

AOICRIE 4PCS L298N Motor Drive Controller Board Module Dual H Bridge DC Stepper for Arduino

  • L298N as Main driver chip L298N, strong driving ability, strong anti-interference, low calorific value, afterflow diode protection, more stable and reliable for Arduino projects, Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability..
  • Double H bridge design, can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors, high efficient, To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage..
  • Driving DC motor Because the module is drived by double H bridge,it can drive two motors simultaneously.Input the following driving timing from IN1-IN4 then the speed and direction of the stepper motor can be controlled..
  • Easy to Use No assembly required. This L298N board comes ready to go. Just wire up motors and power, easy to use..
  • Wide Usage Great for DIY Smart Car Robot Power MEGA R3 for Mega2560 Duemilanove, if driving voltage is more than 12V, use external standard 5volt TTL outputs to switch the H-bridge circuits..
Check Stock

3 Axis CNC Kit Nema23 Stepper Motor Dual Shaft 425oz-in 112mm 3A & Driver 40VDC 4A 128 microstep for CNC Router Milling Engraving Machine

  • ♞【Product】3 Axis nema23 stepper motor driver usbcnc controller kit.
  • ♞【Nema 23 Stepper Motor】 Nema 23 Stepper Motor / Holding Torque: 425oz-in,280Ncm / Motor Size:57x57x112mm / Phase:2 / 4pcs lead wire / 1.8 Step.
  • ♞【Stepper Motor Driver】FMD2740C Stepper Motor Driver / 4Amps / Support voltages:12 to 50V DC / 128microstep.
  • ♞【4 Axis USBCNC breakout board】 Come with Hand Control with USB Cable / Only support USBCNC software / input voltage: 15-36V DC..
  • ♞【DC Power Supply】400W 36V 11A DC Switching power supply.
Check Stock

18/4 AWG Shielded CNC Wire (50FT) — Flexible Stranded Shielded 18-Gauge 4-Conductor Cable for Stepper Motors, CNC Machines, NEMA Motors, VFD Spindles, CNC Routers, 3D Printers and more!

  • RESILIENT & FLEXIBLE: Stepper motor cable designed to bend smoothly in your CNC or 3D printer chain!.
  • SHIELDED 4 CONDUCTOR WIRE: Reduce interference for your CNC spindle motor or stepper motor driver!.
  • BEST RESULTS: Shielded wire means higher quality for your 3D Printer, CNC Machine or CNC Controller..
  • GREAT FOR All STEPPER MOTORS: Nema 17 Stepper Motor, Nema 23 Stepper Motor, Stepper Driver, & more!.
  • STEPPER MOTOR WIRE: The perfect upgrade to any CNC Kit, CNC Router Kit, or CNC Stepper Motor Kit..
Check Stock

LAFVIN 5 Sets 28BYJ-48 ULN2003 5V Stepper Motor + ULN2003 Driver Board for Arduino

  • Stepper motor with a standard interface..
  • A, B, C, D four-phase LED indicates the status of the stepper motor work..
  • Drive Module Board Size(in): 1.37*1.18*0.6.
  • 5 line 4 phase can be used for ordinary ULN2003 chip driver, connect to the 2 phase , support the development board,With convenient use, direct docking.
  • Package Content: 5 set 28BYJ-48 Stepper Motor + Uln2003 Driver Board +20pcs female to male Dupont cable (as a gift).
Check Stock

MEGA 2560 Starter Kit Ultra (100% Arduino IDE Compatible) w/ Battery Holder, Sensors, Modules, Resistor kit and Components (no Supply)

  • ...RC-522 RFID Module with white RFID Card and RFID Keychain -High-precision RTC Real-Time Clock Module DS3231 and EEPROM AT24C32 -PIR Presence Sensor HC-SR501 -Distance measurement module HCSR04 -Sound sensor detector module with programmable threshold -LM35 temperature sensor -Tilt detector module -Servo SG90 motor -Stepper motor (5V) -Motor driver module for stepper motor ULN2003.
  • 5V Active Buzzer -5V Passive Buzzer -LCD 1602 16 characters * 2 lines -LED Display Driver MAX7219 -LED Matrix Display of 8*8 -7 Segments Display 1 digit -7 Segments Display 4 digits -Simple Relay Module - Infrared Remote Control 38kHz - 38kHz Infrared decoder receiver (type 1838) - Infrared phototransistor (Flame sensor) - Infrared LED - Light sensor (Photoresistor).
  • -10 * LEDs 5mm Diffused RED -10 * LEDs 5mm Diffused GREEN -10 * LEDs 5mm Diffused YELLOW -5 * LEDs 5mm Ultrabright WHITE diffused -3 * LEDs 5mm Red / Green / Blue Diffused RGB -Shift Register (Series to Parallel IC) 74HC595 - NPN Transistor BC547 - PNP Transistor BC557 - Adjustable Knob Resistor 1kOhm (Potentiometer) - Adjustable Knob Resistor 10kOhm (Potentiometer).
  • - Resistor Pack 1/4W 1% accuracy, with 10pz of each value: 100, 220, 330, 470, 1K, 2K2, 4k7, 10K, 22K, 47K, 100K, 220K, 1M - 40-pin header 2.54 mm -4....
Check Stock

GeeekPi 5 Pack Geared Stepper Motor 28BYJ-48 5V Stepper Motor + Uln2003 Motor Driver Board + Dupont Wire Jumper Wires Ribbon Cables Compatible with Arduino

  • 5pcs Stepper motor and driver board compatible with arduinoIDE 2560 1280 DSP ARM PIC AVR STM32 Raspberry Pi..
  • Stepper motor with a standard interface could be connected with Driver Board easily.
  • A, B, C, D four-phase LED indicates the status of the stepper motor work..
  • 5 line 4 phase can be used for ordinary ULN2003 chip driver, connect to the 2 phase , support the development board, with convenient use, direct docking..
  • Package Includes:5 x Stepper Motor,5 x ULN2003AN Driver Board,30 x Female-to-female jump wire.
Check Stock

6 PCS 28BYJ-48 ULN2003 5V Stepper Motor + ULN2003 Driver Board for Arduino

  • ❃❃ The stepping motor is a kind of mechanical and electrical device that converts electrical pulses into angular displacement. Come with a standard interface, when used directly pluggable..
  • ❃❃ Drive Module Board Size(in): 1.37 * 1.18 * 0.6(in).
  • ❃❃ A, B, C, D four-phase LED indicates the status of the stepper motor work..
  • ❃❃ 5 line 4 phase can be used for ordinary ULN2003 chip driver, Connect to the 2 phase, Support the development board, With convenient use, direct docking..
  • ❃❃ Great packing in a box : 6 PCS ULN2003 Stepper Motor + Driver Board (with a little gift)..
Check Stock

Longruner 5X Geared Stepper Motor 28byj 48 Uln2003 5v Stepper Motor Uln2003 Driver Board with ArduinoIDE (no Wire)

  • 5pcs Stepper motor and driver board compatible with 2560 1280 DSP ARM PIC AVR STM32 Raspberry Pi..
  • Stepper motor with a standard interface. A, B, C, D four-phase LED indicates the status of the stepper motor work..
  • Motor diameter: 1.1 inches.Wire length:9.05 inchs. Stepping angle: 5.625 x 1/64.Reduction ratio: 1/6.Drive Module Board Size:1.26 inchsX1.38inchs. Cable length: about 20cm /8-inch..
  • Great packing in a box : 5 set Uln2003 Stepper Motor + Driver Board..
Check Stock

Eiechip® CNC 3D Printer Kit for Arduino Mega 2560 R3 + RAMPS 1.4 Controller + LCD 2004 + 6X Limit Switch Endstop + 5 A4988 Stepper Driver 3D Printer Interface & Driver Modules

  • 3D Printer Accessories Set meets most needs. Including CNC Shield V3.0, UNO R3 Board, A4988 StepStick Stepper Motor Module..
  • The 3D printer stepper motor shield V3 can be used as driver expansion board for engraving machines and 3D printers..
  • It has in total 4 channel slots for A4988 stepper motor driver modules for driving 4 channel of stepper motors..
  • Each channel of stepper motor only needs 2 IO ports, which means 8 IO ports is sufficient to manage 3 stepper motors..
  • This shield can make quick work for managing stepper motors in your project..
Check Stock

Zrong 3D Printer Parts DRV 8825 DRV8825 Stepper Motor Driver Module 4 PCB Board Replace A4988

  • The DRV8825 stepper motor driver is a breakout board for TI’s DRV8825 microstepping bipolar stepper motor driver..
  • The module has a pinout and interface that are nearly identical to those of our A4988 stepper motor driver carriers, so it can be used as a....
  • The DRV8825 features adjustable current limiting, overcurrent and overtemperature protection, and six microstep resolutions (down to 1/32-step). It....
Check Stock