Reviews Servo To Multiplexer Board

6pcs CD74HC4067 CMOS 16 Channel 16 CH Digital Analog Multiplexer Breakout Module for Arduino

  • This is a breakout board for the very handy 16-Channel Analog/Digital Multiplexer/Demultiplexer CD74HC4067..
  • Use the CD74HC4067 16-channel analog signal switch.
  • Analog signal input: C0-C15 16 channels..
  • IT can be used the very handy 16-Channel Analog/Digital Multiplexer/Demultiplexer CD74HC4067..
  • Wide operating temperature range: -55C to 125C.
Check Stock

15 Pieces Servo Extension Cables Servo Extension Male to Female RC Servo Extension Cord Wire Cable Compatible with RC JR Futaba RC Car Airplanes (3.9 Inch,5.9 Inch,11.8 Inch,19.7 Inch,23.6 Inch)

  • Wide application: these servo extension s are compatible with Futaba and JR servo, plane and helicopter servo connection or receiver connection, also nice for remote control car, RC car and more.
  • Appropriate sizes: the servo extension cord measures approx. 3.9 Inch, 5.9 Inch, 11.8 Inch, 19.7 Inch, 23.6 Inch in length, different size for your use, the color is black and red.
  • Package includes: this package includes 15 pieces of male to female servo extension cables, enough quantity for you to use and replacement, providing more convenience for you.
  • Feature: this male to female servo extension cord featured with female connector on one side, and male connector on the other side, can be connected to the receiving set and steering engine.
  • Useful function: the servo extension wire is suitable for jumping from board to board, or can be applied to control panel cable remote control, which is male to female.
Check Stock

Treedix TCA9548A I2C Multiplexer Breakout Board 8 Channel Expansion Board with pi Header for Arduino

  • The TCA9548A Breakout board supports communicating with multiple I2C devices with the same address, making it easy to interface with them..
  • TCA9548A multiplexer features: bidirectional eight-channel I2C multiplexer, active low reset input.
  • The default address of this expander is 0x70, the address can be changed, and can be set within 0x70~0x77..
  • In the address of 0x70~0x77, 8 expanders can be cascaded, and each expander can be connected to 8 devices with the same address, so that the same I2C port can be connected to 64 devices with the same address and can be used normally..
  • The chip is compatible with 3V and 5V and can be used with any logic level.
Check Stock

BotBrain Robotics Control Board

  • Basic Stamp microprocessor, the board uses sensor inputs, a program, and servo outputs to operate a robot using the Parallax pBasic language.
  • Features include 8 sensor inputs and 5 servo outputs, all with polarized connectors as well as a built-in piezo "speaker".
  • Holes on side on the side of the board bolt to Merkur parts.
Check Stock

9 Pieces JST Y Connector 3 Pin JST Plug Splitters Servo Extension JST Male to Female RC Servo Extension Cord Wire Cable Compatible with RC JR Futaba RC Car or Airplanes (Mixed Style)

  • Package includes: you will 9 pieces of servo extension cord, 3 pieces of male JST to female JR (Futaba) cable, 3 pieces of male to 2 female Y harness, 3 pieces of male to 3 female Y harness.
  • Abundant quantity and diverse styles that can meet your various needs.
  • Appropriate sizes: the servo extension cord measures approx. 15 cm/ 5.9 inches in length, universal size for your use, the color is white, black and red.
  • Extensive usages: these JST male to female are compatible with Futaba and JR servo, plane and helicopter servo connection or receiver connection, also nice for remote control car, RC car and more.
  • Well made: JST connector is made of quality PVC material, with good insulation and flame retardant.
  • The interior is made of tinned copper, which has a good transmission and low resistance.
  • Useful function: the servo extension wire is suitable for jumping from board to board, or can be applied to control panel cable remote control unit, which is male to female.
Check Stock

10 pcs 3.93inch JR Style Servo Extension Cable Lead Wire - 3-Pin JR Plug Male to Male RC Servo Wire Extension Cord

  • 3-Pin JR plug male to male connector servo extension lead wire cable..
  • There is a 3 pin JST RE connector on each end. This is a simple 3 wire cable. Ideal for jumping from board to board, or something else..
  • Practical range: For Airplane, Helicopter, Quad co-pterter , Multi-coater RC car servo connection or receiver connection..
  • Packaging quantity ：10 Pcs * 10cm JR 3pin male to male plug servo extension cables wires cords leads..
Check Stock

15 Pcs Servo Extension Cable JST Y Connector 3 Pin JST Plug Splitters Male to Female Servo Adapter JST Extension Servo Wire Connector Compatible with RC JR Futaba RC Car or Airplanes, 3 Styles

  • You Will Get: the package comes with 15 pieces of servo extension cables, including 5 pieces of male JST to female JR (Futaba) cable, 5 pieces of male to 2 female Y harness, 5 pieces of male to 3 female Y harness, sufficient quantities and multiple styles can satisfy your different using needs.
  • Proper Size: the servo connector is about 15 cm/ 5.9 inches in length, suitable size for your to use, with colors of white, black and red.
  • Wide Application: these JST plug splitters are compatible with Futaba and JR servo, plane and helicopter servo connection or receiver connection, also suitable for remote control car, RC car and so on, providing a lot of usages for you.
  • Nice Craftmanship: the JST plug connector is made of quality PVC material, which has good insulation and flame retardant, and the interior is made of tinned copper, featured a good transmission and low resistance performance, you can rest assured to use it.
  • Practical Function: the servo wire connector can be applied for jumping from board to board, or nice to control panel cable remote control part that is male to female.
Check Stock

MakerFocus PWM Servo Motor Driver IIC Module 16 Channel PWM Outputs 12 Bit Resolution I2C Compatible with Raspberry Pi 4 3B+ 3B Zero/Zero W/Zero WH and Jetson Nano

  • Note: The Raspberry Pi and Servo in the photo are not included. User Manual: Please get the link from the operation guide below.
  • Note: 1.If you only connect 5V power supply to USB interface, servo cannot be driven.
  • 2.You should connect higher power supply for higher-power servo.
  • 3.Make sure servo are connected properly, otherwise they will not move..
  • Servo Motor Driver: You may have tried to control a robotic arm or a hexapod walker by using the Raspberry Pi, but finally get frustrated due to the limited number of PWM outputs and the jittering servo. Now you get a new option to bring your ideas to life, we prepare this useful Servo Driver Board for you..
  • Raspberry Pi connectivity, compatible with Raspberry Pi 4 3B+ 3B 2B+ 2B Zero/Zero W/Zero WH and Jetson Nano..
  • Up to 16-Channel servo/PWM outputs, 12-bit resolution for each channel (4096 scales).
  • Integrates 5V regulator, up to 3A output current, can be powered from battery through VIN terminal..
Check Stock

(5PCS) SN7447AN IC BCD-TO-7SEG DECODR/DVR 16-DIP 7447 SN7447

  • 74HC4051 8-Channel-Mux Multiplexer Selector Module Distributor Resolver CJMCU-4051 Development Board.
Check Stock

NOYITO CD74HC4067 CMOS 16-Channel Digital Analog Multiplexer Breakout Module

  • Function: Use 16 ADCs to collect 16 analog signals.003cbr003e.
  • Use the CD74HC4067 16-channel analog signal switch.
  • Analog signal input: C0-C15 16 channels.003cbr003e.
  • This is a breakout board for the very handy 16-Channel Analog / Digital Multiplexer / Demultiplexer CD74HC4067.003cbr003e.
  • This chip is like a rotary switch - it internally routes the common pin (COM in the schematic, SIG on the board) to one of 16 channel pins (CHANxx). It works with both digital and analog signals (the voltage can't be higher than VCC), and the connections function in either direction.003cbr003e.
Check Stock

HiLetgo CD74HC4067 CMOS 16 Channel 16 CH Digital Analog Multiplexer Breakout Module for Arduino

  • Function: Use 16 ADCs to collect 16 analog signals..
  • Use the CD74HC4067 16-channel analog signal switch.
  • Analog signal input: C0-C15 16 channels..
  • This is a breakout board for the very handy 16-Channel Analog/Digital Multiplexer/Demultiplexer CD74HC4067..
  • This chip is like a rotary switch - it internally routes the common pin (COM in the schematic, SIG on the board) to one of 16 channel pins (CHANxx). It works with both digital and analog signals (the voltage can't be higher than VCC), and the connections function in either direction..
Check Stock

Premium Mini CCTV Video Recorder with Split-Screen Views + IR Remote

  • The 4Ch Video Color Quad Multiplexer allows several video signals from CCTV security cameras or other analog video devices to be combined and displayed on one monitor. The video processors are also commonly referred to as video mux, CCTV multiplexer, or color quad processor..
  • 4 Channel Color Quad Multiplexer, Loopout Function, Build-In Buzzer.
  • Multiple Display Modes: 4 pictures, 2 pictures, 1 picture.
  • Video Input: 1.0Vp-p75 ohm, Tape Input/Output: 1.0Vp-p75 ohm.
  • Working Voltage: DC12V/1A, Environmental Temperature: -30°C-60°C.
Check Stock

DIYmall 10pcs 10cm 3.93inch Male to Male JR Plug Servo Extension Lead Wire Cable 3Pin 100mm for RC Plane

  • 10CM Male to Male JR Plug Servo Extension Lead Wire Cable.
  • Great for jumping from board to board or just about anything else..
  • There is a 3-pin JST RE connector on both ends. These are simple jumper wires used on standard 0.1" breakaway headers..
  • Length:100mm Type:JR Plug Servo Extension wire (Male to Male).
Check Stock