Reviews Servo To Pwm Board

Servo Driver HAT 16-Channel 12-bit I2C Interface PWM Outputs for Jetson Nano Raspberry Pi Zero/Zero W/Zero WH/2B/3B/3B+/4B Supports SG90 MG90S MG996R etc @XYGStudy

  • Servo Driver HAT for Raspberry Pi, 16-Channel, 12-bit, I2C Interface.
  • Needless to say, the Raspberry Pi is powerful enough in most cases, yet it's not that good at providing precise PWM output. You may have tried to....
  • Standard Raspberry Pi 40PIN GPIO extension header, compatible with Raspberry Pi Zero/Zero W/Zero WH/2B/3B/3B+/4B and later version, Jetson Nano.
  • I2C controlled, using only 2 pins Standard servo interface, supports common used servo such as SG90, MG90S, MG996R, etc..
  • Up to 16-Channel servo/PWM outputs, 12-bit resolution for each channel (4096 scales).
Check Stock

KEYESTUDIO Plus Board for Arduino UNO R3 with Type-C USB Cable, 3.3V 5V 1.5A Output Current, More Powerful Controller Board

  • The KEYESTUDIO Plus board can work like the Arduino Board but it is more powerful and has more pins.
  • The USB to Serial chip of this board is stable and compatible CP2102.
  • extend serial communication and I2C interface, 6 PWM and 6 analog ports.
  • special DC-DC design provides up to 5V 1.5A, can drive high-current devices like servo and motor.
  • The yellow text on black board makes identifying pinsets a breeze. FCC and CE is available.
  • How to use: Search for "keyestudio wiki KS0486" in Google Chrome to get the wiki online tutorial for this product. Technical supports are available at any time!.
Check Stock

Aoicrie 5pcs PCA9685 16 Channel PWM Servo Motor Driver PCA9685 IIC Module 12-Bit, for Robot or for Raspberry pi Shield Module servo Shield

  • It is 5V compliant, which means you can control it from a 3.3V microcontroller and still safely drive up to 6V outputs (this is good for when you want to control white or blue LEDs with 3.4+ forward voltages)..
  • Communication Interface: IIC, PCA9685 contain an I2C-controlled PWM driver with a built-in clock..
  • 6 address select pins so you can wire up to 62 of these on a single i2c bus, a total of 992 outputs..
  • 12-bit resolution for each output - for servos, that means about 4us resolution at 60Hz update rate..
  • 16 Channel PWM/Servo Driver IIC interface-PCA9685 for arduino or for Raspberry pi shield module servo shield..
Check Stock

ALAMSCN 5PCS SG90 9g Servo Motor + 16 Channel PWM Servo Motor Driver PCA9685 IIC Module 12-Bit DIY Kit for RC Robot Arm Helicopter Airplane Car Boat Remote Control for Arduino for Raspberry pi

  • These SG90 9G micro servo motors have a completely new redesigned PCB and control system to provide more accuracy..
  • Its internal gearing and motor are also upgraded to improve dead bandwidth and centering..
  • For SG90 9G micro servo motor is far more accurate and safe to use in aircraft which require precise servo movements and perfect centering..
  • Apply to remote control helicopters, micro robot, robot arm and boats. Fit for ALL kind of R/C Toys and also make electronics DIY based on Arduino ,Raspberry Pi..
  • Package includes: 5PCS SG90 9g Micro Servo + 1PC PWM Servo Motor Driver. Cost-effective kit to meet your DIY needs..
Check Stock

ZOSKAY 1X DS3218 Update servo 20KG Full Metal Gear Digital servo Baja servo Waterproof servo for Baja Cars(Control Angle 180)

  • DS3218 20KG Large Torque Digital Servo with precision potentiometers,stable,low noise,waterproof: IP66.
  • High-precision metal gears with hard anodizing, CNC aluminium middle Shell, Dual ball bearings.
  • Large Torque&speed – 18.5kg.cm (0.16S/ 60°)@5V,maximum 21.5 kg.cm (0.14S/60°)@6.8V Operating travel:180°（PWM 500-2500μs）.
  • High performance digital standard servo for any crawler.
  • and for robot joint activities,TRX 4 Traxxas， SMT10 Mega Truck， SCX10 II，ARRMA Nero 1/8…..
  • Package Included: 1 x Digital Servo 1.58x0.79x1.60inch (40x20x40.5mm).
  • Weight: 60g (2.12oz) 1 x 25T Adjustable metal servo arm.
Check Stock

HiLetgo 5pcs Nano I/O Expansion Sensor Shield for Arduino UNO R1 Nano 3.0 Duemilanove 2009

  • 14 I/O Pin (servo type with GND, power and signal).
Check Stock

AEDIKO MG996R Servo Motor Control 180 Angle Metal Gear Servo Digital High Speed Torque Servo Motor for Smart Car Robot Boat RC Helicopter 2-Pack (MG996)

  • Positioning Speed Without Load: 0.17s / 60 degrees 4.8V.
  • Compliant with Futaba, Hitec, Sanwa, GWS, etc ..
  • Latest Version: MG996R Servo Motor Which Updated from SG90 and MG90S Micro Servo Motor,Made of High Precision Potentiometer and High Resolution Digital Chip to Ensure Stable Performance and Solve Problems:Unsuitable R / C and Slow Response Time.
  • Gear Type: All Metal Gear RC Servo Can Control the Angle Range from 0 to 180, with Precise Control and Gears are Consistent,Which Can Rotate 360 Degrees When Power Off.
  • Application: Analog Servo Motor Great for RC Helicopters, Micro Robots,Robotic Arms and RC Rock Crawler, RC Boat Motor,Truck, Boat, Racing Car,Various Remote Control Toys and Arduino Experiments.
Check Stock

15 Pieces Servo Extension Cables Servo Extension Male to Female RC Servo Extension Cord Wire Cable Compatible with RC JR Futaba RC Car Airplanes (3.9 Inch,5.9 Inch,11.8 Inch,19.7 Inch,23.6 Inch)

  • Wide application: these servo extension s are compatible with Futaba and JR servo, plane and helicopter servo connection or receiver connection, also nice for remote control car, RC car and more.
  • Appropriate sizes: the servo extension cord measures approx. 3.9 Inch, 5.9 Inch, 11.8 Inch, 19.7 Inch, 23.6 Inch in length, different size for your use, the color is black and red.
  • Package includes: this package includes 15 pieces of male to female servo extension cables, enough quantity for you to use and replacement, providing more convenience for you.
  • Feature: this male to female servo extension cord featured with female connector on one side, and male connector on the other side, can be connected to the receiving set and steering engine.
  • Useful function: the servo extension wire is suitable for jumping from board to board, or can be applied to control panel cable remote control, which is male to female.
Check Stock

PC Interface Controller

  • 【One-year after-sale warranty】The PWM to voltage module converts PWM digital signals to 0 to 10V analog signals. It can be used to switch the signal interface of PLC or other industrial control board. Adjust the output voltage by adjusting the PWM duty cycle. The module is small in size and easy to apply in different places.003cbr003e.
  • Using MCU embedded technology. Easy to operate, can be fine-tuned by potentiometer.003cbr003e.
  • Select the PWM signal input level range by short circuit. The module is small, easy to carry and easy to use.003cbr003e.
  • (current greater than 100mA)，PWM signal receiving frequency range: 1KHZ-3KHZ.
  • When power on for the first time, it is best to do a calibration and debugging: find a signal with a 50% duty cycle and connect it to PWM and GND. Jumper caps set the corresponding voltage range. When the frequency is 1KHZ-3KHZ, use a multimeter to measure the two ports of VOUT and GND. At this time, the meter displays about 5V. Adjust the potentiometer on the board so that the multimeter displays 5.00v.003cbr003e.
Check Stock

AEDIKO MG995 Servo Motor Control 180 Angle Metal Gear Servo 20KG Digital High Speed Torque Servo Motor for Smart Car Robot Boat RC Helicopter 2-Pack (MG995)

  • Positioning Speed Without Load: 0.17s / 60 degrees 4.8V.
  • Compliant with Futaba, Hitec, Sanwa, GWS, etc ..
  • Latest Version: Micro Servo Made of High Precision Potentiometer and High Resolution Digital Chip to Ensure Stable Performance and Solve Problems:Unsuitable R / C and Slow Response Time.
  • Gear Type: All Metal Gear RC Servo Can Control the Angle Range from 0 to 180, with Precise Control and Gears are Consistent,Which Can Rotate 360 Degrees When Power Off.
  • Application: Analog Servo Motor Great for RC Helicopters, Micro Robots,Robotic Arms and RC Rock Crawler, RC Boat Motor,Truck, Boat, Racing Car,Various Remote Control Toys.
Check Stock

Yahboom RC Servo Tester 1 8 16 Channels Servo Motors Controller Centering Tool with Over-Current Protection, 2 Control Modes (Servo Tester 8 chan)

  • 8-channel independent servo interface and 8 high-precision potentiometers..
  • Support manual mode,centering mode,which can be switched by function keys.
  • Terminal block （5-8.4V）power supply port,with Over-Current Protection. Compatible with any 5V-8.4V servos..
  • Control accuracy: 0.09 degrees(PWM limit small change value 1us).
  • Wide range of applications.No need any codes, servo can be controlled by buttons or the adjustable knobs..
Check Stock

LRONG 1PC PC Chassis Fan Hub CPU Cooling HUB Fan PWM Hub SATA Controller Speed Controller

  • 12V 10-way 4pin SATA fan hub, to solve the problem of insufficient motherboard fan ports. The hub has 10 fan ports, can support 10 fans, can meet various host requirements, and supports 3pin/4pin fans..
  • Installation steps: The PWM port is connected to the CPU fan port on the motherboard. The red port is dedicated to the CPU fan. Connect 1 fan to the red portand then connect the rest of the fans. Then you need to connect the fan hub’s PWM cable to the motherboard. Connect the SATA cable to the fan hub..
  • Equipped with PWM cable: The hub is equipped with a PWM cable with a length of 40CM, which can support the back line. After the PWM cable is connected to the main board, the temperature control and speed can be controlled by the main board..
  • Convenient installation: the hub is fixed with 3M glue, and the back of each hub is equipped with an American 3M glue, which can make the hub work well.
  • Package content: 1 X 12V 10-channel 4pin fan hub, 1X PWM connection cable..
Check Stock

6 Axis 125KHz NVCM USB Mach3 Stepper Motor Motion Control Card Breakout Board USB interface CNC Controller Board 12-32VDC for Servo Motor

  • ♞【Support software】This NVCM card support Mach3 software, through USB port to communicate with computer..
  • ♞【DC power supply input】main device is 12V-32V DC power supply input,current should higher than 1A.
  • ♞【Max 6 Axis Control】Can support 6 axis stepper systems maxisim,125KHz pulse output for every axis.
  • ♞【PWM output】1 port 0-10V spindle speed analog output interface(can change to PWM output).
  • ♞【Multifunction】 Power supply interface, USB connection interface, Stepper/Servo control output interface, spindle control output interface,....
Check Stock