Reviews Rear Bearing- BestItemr.com

OTC 6540 Rear Axle Bearing Puller Set - 8 Piece

Set contains slide hammer and popular attachments needed for servicing flange type floating rear axle bearing and seals in most late model rear wheel drive cars and light trucks.
Includes 3 sizes of rear axle bearing pullers.
Slide hammer tee bar and Slide hammer 5 LB head weight.
Pulling hook rear axle pulling plate and bearing cup remover.

NO SHOP PRESS NEEDED: Remove the need for a shop press with our wheel hub bearing press tool.
Save time removing even seized-up wheel hub and bearing....
FOR PRO AND DIY MECHANICS: This wheel bearing puller/installer is one of the only tools for servicing front and rear wheel hubs and bearing on German....
TIME-SAVING BEARING TOOL: No need to remove the strut assembly or knuckle to remove/install the hub and bearing.
VARIETY OF ADAPTERS: Service your vehicles easily with our rear and front wheel bearing removal kit.
This wheel bearing removal tool features all the....
DURABLE STEEL CONSTRUCTION: Our rear and front wheel drive bearing adapter kit's steel design holds up to the torque required to remove hubs and....

EASY TO USE: Slide flat end of puller through center of bearing and flat against backside of bearing, then slide washer down the center of the shaft against front side of bearing and tighten the nut on smaller end of puller, then thread a slide hammer (not included) to the puller and slide hammer back and forth until the bearing comes out.
The washer captures the bearing firmly to distribute the applied force over the entire bearing and prevent damage.
Use the VCT Pneumatic SAE Standard Rear Axle Bearing Puller 3-Piece Service Set – Domestic Car Vehicle Bearings Removal Tool Kit to service semi-floating rear axle bearings on your vehicle.
These tools make the job simple and prevent damage to your bearings when pulling.
Much easier than claw-type axle bearing pullers that slip off and chew up the old bearings.
For removal only, not intended for installation.
FITS YOUR CAR: Standard SAE sizes work for most American domestic makes and models.
Set includes the following sizes to fit main bearing tube – 1 inch to 1-7/8 inches, 1-5/16 inches to 2-3/8 inches, and 1-3/8 inches to 2-7/8 inches.
Sizes permanently laser-etched on tool for easy identification.
Each tool fits a basic slide hammer with a 5/8-inch x 18 thread pitch.

Application: Suitable for 1999-2008 Honda TRX 400 EX and 2009-2014 Honda TRX 400 X..
Function: The rear axle bearing frame is an aftermarket replacement manufactured according to OEM bearing frame specifications..
Advantage: Compared with tapered bearings, the double-row bearing in the rear row can realize more flexible chain adjustment and less maintenance..
Material: Made of sturdy and light 6061-T6 billet to ensure corrosion resistance and rust resistance to improve durability..
Design：Designed with high temperature, tensile spring radial lip grease seals, which can protect the components from external components. The rear double-row bearing frame is equipped with a central grease plug, which can be quickly and easily lubricated without disassembly..

Direct Fit, OE Replacement Wheel Bearing Assembly Kit.
Kit Includes: (1) Rear Passenger Side Wheel Bearing & Hub Assembly.
(1) Rear Driver Side Wheel Bearing & Hub Assembly.
Vehicle Specific: Check fitment information in the listing for compatibility.
Aftermarket Reference Number(s): 0516330,432024BA0B,43202EN100,43202JG200,512373,712373,HA590235.

Specs: Differential Bearing and Seal Kit Rear, Contains: 3 Ball Bearings, 1 Needle Bearing, 3 Seals, 2 Snap Rings.
Kits contain all of the bearings and seals required trepair your differential.
Compatible With/Replacement For: Honda TRX500FA 2005 - 2014, TRX500FE 2005 - 2011, TRX500FGA 2005 - 2008, TRX500FM 2005 - 2011, TRX500FPA 2009 - 2014, TRX500FPE 2007 - 2011, TRX500FPM 2008 - 2011, TRX500TM 2005 - 2006.
100% New aftermarket Differential Bearing and Seal Kit Rear built to meet OEM specifications.

Fully milled gearbox housing made of 6061-T6 aluminum for the rear axle of ATOPRC.
Due to its dimensional stability results in a higher load capacity and service life of bevel gear and ball bearings. The problem of the torn fastening thread has an end with this case.
The bearing adapters are included in the set.
We recommend gluing the bearings with threadlocker y0113. For mounting the bearing adapters in the housing we recommend Bindulin silicone y19015. To use HD differential shafts y1477, the Atoprc bearing adapters must be machined.

Please verify your year, make and model in the product details before purchasing..
OEM Replacement. Brand New Complete Rear Wheel Axle and Bearing Carrier.
Stock Length rear wheel axle & bearing carrier.
This axle is an OEM replacement for the following OEM # 5LP-25381-10-00 / This bearing carrier is an OEM replacement for the following OEM # 5LP-25311-10-00.

☛Strong Compatibility — For 1987-2007 Honda TRX300EX 300EX, Fits 1987-2007 Honda TRX300EX 300EX DUAL ROW Rear Axle Carrier Bearing..
☛Superior Material — Our Rear Axle Bearing Carrier body is CAD engineered and CNC machined from billet 6061-T6 aluminum and steel, light weight,....
☛Upgrade Design — Our Rear Axle Bearing Carrier are special designed with a high-temperature, tension spring radial lip grease seals to ensure....
☛High Performance — Come complete with heavy duty double row bearings, seals, and a steel center tube. They feature sealed bearings that are....
☛Satisfaction Guarantee — If you're not 100% satisfied with our products, simply return it in 30 days for a full refund, with unconditional refund....

✦ride fixed gear or freewheel with a flip-flop hub, including front and rear brakes, suitable for commuters.
▲Practice hands flexibly, the rear hub still uses the bearing 4 bearing rear hub,.
▲Stable performance, nowadays the popular upper cover raises the short stem,.
▲2-layer aluminum alloy rims, aluminum alloy chainrings, and other accessories are also of good quality,.

this item i a PTC BRAND NEW OEM tyle replacement REAR Bearing for the rear of your Truck TO PROVIDE PROPER BEARING CLEARANCE 3 OEM APPROVED DEIGN 4....

19" front and 16" rear wheel assembly for pit pro trail dirt bike.
Front wheel comes with the 1.6 x 19 rim, 70/100-19 knobby tire, inner tube, wheel bearing.
Rear wheel comes with the 1.85 x 16 rim, 90/100-16 knobby tire, inner tube, wheel bearing.
Package include: 1 x front wheel + 1 x rear wheel.