Reviews Motor Driver Board

BIQU LCD 12864 Version Graphic Smart Display Controller Module with Adapter and Cable for RAMPS 1.4 Reprap 3D Printer Kit

  • 2560 control board: The board is a microcontroller board based on the 16AU .It has 54 digital input/output pins (of which 14 can be used as PWM....
  • RAMPS 1.4: RAMPS interfaces an for Arduino with the powerful for Arduino platform and has plenty room for expansion. The modular design includes plug....
  • LCD 12864 with Controller: This full graphic Smart Controller contains a SD-Card reader, an rotary encoder and a 128 x 64 dot matrix LCD display. You....
  • A4988 driver module: A4988 Stepper Motor Driver Board is a breakout board for Allegro?ˉs A4988 DMOS Microstepping Driver with Translator and....
  • Warning: Connecting or disconnecting a stepper motor while the driver is powered can destroy the driver. (More generally, rewiring anything while it....
Check Stock

LAFVIN 5 Sets 28BYJ-48 ULN2003 5V Stepper Motor + ULN2003 Driver Board for Arduino

  • Stepper motor with a standard interface..
  • A, B, C, D four-phase LED indicates the status of the stepper motor work..
  • Drive Module Board Size(in): 1.37*1.18*0.6.
  • 5 line 4 phase can be used for ordinary ULN2003 chip driver, connect to the 2 phase , support the development board，With convenient use, direct docking.
  • Package Content: 5 set 28BYJ-48 Stepper Motor + Uln2003 Driver Board +20pcs female to male Dupont cable (as a gift).
Check Stock

3D Printer Controller Kit RepRap RAMPS 1.4 + 2560 Board + 5pcs A4988 Stepper Motor Driver with Heatsink + LCD 12864 Graphic Smart Display 3D Printer Controller Kit

  • 2560 control board: The board is a microcontroller board based on the 16AU .It has 54 digital input/output pins (of which 14 can be used as PWM....
  • RAMPS 1.4: RAMPS interfaces an for Arduino with the powerful for Arduino platform and has plenty room for expansion. The modular design includes plug....
  • LCD 12864 with Controller: This full graphic Smart Controller contains a SD-Card reader, an rotary encoder and a 128 x 64 dot matrix LCD display. You....
  • A4988 driver module: A4988 Stepper Motor Driver Board is a breakout board for Allegro?ˉs A4988 DMOS Microstepping Driver with Translator and....
  • Warning: Connecting or disconnecting a stepper motor while the driver is powered can destroy the driver. (More generally, rewiring anything while it....
Check Stock

6 PCS 28BYJ-48 ULN2003 5V Stepper Motor + ULN2003 Driver Board for Arduino

  • ❃❃ The stepping motor is a kind of mechanical and electrical device that converts electrical pulses into angular displacement. Come with a standard interface, when used directly pluggable..
  • ❃❃ Drive Module Board Size(in): 1.37 * 1.18 * 0.6(in).
  • ❃❃ A, B, C, D four-phase LED indicates the status of the stepper motor work..
  • ❃❃ 5 line 4 phase can be used for ordinary ULN2003 chip driver, Connect to the 2 phase, Support the development board, With convenient use, direct docking..
  • ❃❃ Great packing in a box : 6 PCS ULN2003 Stepper Motor + Driver Board (with a little gift)..
Check Stock

Longruner 5X Geared Stepper Motor 28byj 48 Uln2003 5v Stepper Motor Uln2003 Driver Board with ArduinoIDE (no Wire)

  • 5pcs Stepper motor and driver board compatible with 2560 1280 DSP ARM PIC AVR STM32 Raspberry Pi..
  • Stepper motor with a standard interface. A, B, C, D four-phase LED indicates the status of the stepper motor work..
  • Motor diameter: 1.1 inches.Wire length：9.05 inchs. Stepping angle: 5.625 x 1/64.Reduction ratio: 1/6.Drive Module Board Size:1.26 inchsX1.38inchs. Cable length: about 20cm /8-inch..
  • Great packing in a box : 5 set Uln2003 Stepper Motor + Driver Board..
Check Stock

DGZZI 2Set 28BYJ-48 DC 5V Geared Stepper Motor + ULN2003 Driver Test Module Board for Arduino

  • A, B, C, D four-phase LED indicates the status of the stepper motor work..
  • Stepper motor with a standard interface, when used directly pluggable..
  • 5 line 4 phase can be used for ordinary..
  • ULN2003 chip driver, connect to the 2 phase, support the development board, With convenient use, direct docking..
  • Package includes: 2* 28BYJ-48 Stepper Motor + 2* Uln2003 Driver Board.
Check Stock

BIGTREETECH SKR V1.4 Turbo Control Board 32bit for 3D Printer Compatible with TFT35 E3 V3.0.1/TFT70 Touch Screen Support TMC2209/TMC2208/TMC5160/TMC2130 for Most FDM 3D Printer (with 5*TMC2209)

  • ...ard TMC-driven SPI working mode and UART working mode, and the on-board DIAG function pins are convenient for customers to use, eliminating the complicated wiring process, which can be used by simply removing and inserting the jumper cap..
  • ✨Compare to other stepper motor driver in the market, our TMC2209 silent stepper driver generate lower heat and it has a large-area cooling position to lower the temperature. It driver can lower 30% heat than others stepper motor drivers even working last for a long time. With Passive cooling on a 10 hours print, they only hit 37℃..
  • ✨BIGTREETECH TMC2209 V1.2 is an ultra-silent motor driver IC for two-phase stepper motors, which adopts stealthChop2 Mute technology which reduces motor noise to the point of silence at low velocities to ensures noiseless operation, maximum efficiency and best motor torque. spreadCycle allow for highly dynamic motion. Drive current 2A, peak current 2.8A, voltage range 4.75V-29V, 256 subdivision..
Check Stock

YJYGR 3D Printer Motherboard MKS Gen V1.3 Ramps1.4 & 2560 Compatible MKS GEN V1.4 Motherboard Driver Board

  • 1. Integrating 2560 and ramps1.4 on one board, which solves the problem that the Ramps1.4 combination interface is complicated and prone to failure..
  • 4. The use of high-quality MOSFET tube has better heat dissipation effect..
  • 2. Replaceable motor driver, support 4988 driver, 8825 driver, TMC2100 driver.
  • 3. The circuit board uses a high-quality 4-layer board, and has been specially optimized for heat dissipation.
  • We are a professional Amazon store. If you have any questions, you can contact us at any time. We sincerely create a good buying experience for every customer who comes to each store..
Check Stock

3 Axis Stepper Motor CNC Router Kit Nema23 425oz-in 112mm Dual Shaft+CW5045 Driver 4.5A 256 microstep+400W 36V Power Supply CNC Controller Kit for Engraving Lathe Plasma Milling Drilling Machine

  • ♞【Product】3 Axis nema23 stepper motor driver controller kit.
  • ♞【Application】This cnc kit are widely used in engraving machine, printer,....
  • ♞【Stepper Motor】23HS2430B Nema23 57 stepper motor.
  • ♞【Driver】CW5045 driver Voltage: DC 24-50V.
  • Current: rated maximum output reaches: ±4.5A.
  • ♞【5 Axis Breakout Board】5 Axis breakout boad with cables,this breakout board needs to be connected to the parallel port and USB port of the....
  • ♞【Power supply】400W,36V/9.7A switching power supply.
Check Stock

sb components Raspberry Pi Pico Board with Pico Motor Driver HAT Connects 2 DC and 1 Stepper Motor DC Motor Control Module for Raspberry Pi Pico, Raspberry Pi Pico Kit

  • Raspberry Pi Pico is Raspberry Pi's first microcontroller board, designed especially for physical computing.
  • It can be easily reprogrammed over USB from a Raspberry Pi or other computer using the C/C++ SDK or the official MicroPython port.
  • Pico Driver Motor HAT is a DC motor control module that is powered by one H-bridge IC L293D with the motor input supply range 6 V-24 V.
  • Pico Driver Motor HAT is specifically made to work with the Raspberry Pi Pico Board.
Check Stock

Zrong 3D Printer Parts DRV 8825 DRV8825 Stepper Motor Driver Module 4 PCB Board Replace A4988

  • The DRV8825 stepper motor driver is a breakout board for TI’s DRV8825 microstepping bipolar stepper motor driver..
  • The module has a pinout and interface that are nearly identical to those of our A4988 stepper motor driver carriers, so it can be used as a....
  • The DRV8825 features adjustable current limiting, overcurrent and overtemperature protection, and six microstep resolutions (down to 1/32-step). It....
Check Stock

Eiechip® CNC 3D Printer Kit for Arduino Mega 2560 R3 + RAMPS 1.4 Controller + LCD 2004 + 6X Limit Switch Endstop + 5 A4988 Stepper Driver 3D Printer Interface & Driver Modules

  • 3D Printer Accessories Set meets most needs. Including CNC Shield V3.0, UNO R3 Board, A4988 StepStick Stepper Motor Module..
  • The 3D printer stepper motor shield V3 can be used as driver expansion board for engraving machines and 3D printers..
  • It has in total 4 channel slots for A4988 stepper motor driver modules for driving 4 channel of stepper motors..
  • Each channel of stepper motor only needs 2 IO ports, which means 8 IO ports is sufficient to manage 3 stepper motors..
  • This shield can make quick work for managing stepper motors in your project..
Check Stock

KOOKYE 2 x 28BYJ-48 DC 5V Stepper Motor + ULN2003 Driver Test Module Board for Arduino Raspberry Pi

  • This is a stepper motor and a stepper motor driver..
  • Mainly used in air conditioner louver, small cooling and heating fan etc. Stable and all technic parameters are qualified for national electronic....
  • On-board ULN2003A chipset,On-board 4-way indicator light,On-board XH-5P socket,Compatible with Arduino..
Check Stock