Reviews Mosfet Motor Driver

YJYGR 3D Printer Motherboard MKS Gen V1.3 Ramps1.4 & 2560 Compatible MKS GEN V1.4 Motherboard Driver Board

  • 1. Integrating 2560 and ramps1.4 on one board, which solves the problem that the Ramps1.4 combination interface is complicated and prone to failure..
  • 4. The use of high-quality MOSFET tube has better heat dissipation effect..
  • 2. Replaceable motor driver, support 4988 driver, 8825 driver, TMC2100 driver.
  • 3. The circuit board uses a high-quality 4-layer board, and has been specially optimized for heat dissipation.
  • We are a professional Amazon store. If you have any questions, you can contact us at any time. We sincerely create a good buying experience for every customer who comes to each store..
Check Stock

SoarUp 35A 4 in 1 ESC, 48mhz Frequency Throttle Response BLHeli‑32 4 in 1 ESC for FPV Traversing Machine

  • 35A ESC and Advanced SMTs: Integrate 4 high performance 35A ESCs, built in galvanometer, and purchase new advanced SMTs. After such high integration, the volume is only the same as that of the control of the traversing aircraft, so the installation.
  • Hardware PWM and Damped Light Technology: Hardware PWM drive motor, less noise, more throttle response. Damped Light technology, regenerative braking function, make motor deceleration more sensitive and effective, control more accurate.
  • BLHeli‑S Firmware and ESC Setting: Using BLHeli‑S firmware has powerful performance and rich functions.
  • it also supports setting ESC parameters in various ways, or upgrading ESC firmware (such as setting or upgrading ESC via throttle signal line, using ot.
  • Support and Input Output Line: It not only supports ordinary PWM throttle signal mode, oneshot 125, oneshot 42 and multshot ultra high speed throttle signals, but also supports the latest dshot150 / 300 / 600 digital throttle, with strong anti interferenc.
  • Main Control Chip and PCB Production: EMF8BB21F16G main control chip, operating frequency up to 48mhz. For mosfet, three in one IC driver and high quality high frequency ceramic capacitor. In high end PCB production process, pads are metallized to avoid p.
Check Stock

Aoicrie MKS Gen L V1.0 3D Printer Integrated Mainboard Controller PCB Board Compatible Ramps1.4/Mega2560 R3 with A4988 Motor Driver for 3D

  • Integrate 2560 and Ramps1.4 one PCB,which designed to avoid complicated connections, easier wiring and more stable Use high-quality 4 layer PCB&Use special power chip,support 12V-24V, also Use Run Marlin firmware,same as configuration way as Ramps1.4, it can replace Ramps1.4 directly..
  • Use high quality MOSFET tube,better cooling and more stable.Use special power chip,support 12-24V input,reduce the heated bed current to 1/4 that slove the Mosfet heat problem efficiently and power shortage..
  • Support a variety of stepper drivers: A4988,DRV8825,TMC2208 and TMC2100, and available to work with LCD2004,LCD12864,MKS TFT24/28/32/35 & Available to connect external large stepp drivers, A4988 driver board widely used in 3D printers and small CNC machines..
  • Support functions: Non-trace resumption after power off, run out filament ,and auto shut down, XTZ axis with different color terminal controls the motors and end stop,which is convenient to wire.Use high-quality 4 layer PCB&Use special power chip.Retail Servos,AUX-1 and AUX-2 interface of Ramps1.4 provide three 5V output and three 12V output interfaces..
  • Five different step resolutions: full-step, half-step, quarter-step, eighth-step, and sixteenth-step.Adjustable current control lets you set the maximum current ....
Check Stock

MKS SERVO42C NEMA17 Closed Loop Stepper Motor Driver Low Noise for CNC 3D Printer Prevent Losing Steps Compatible with Gen L SGen L SKR 2 / V1.4 Turbo BTT Octopus V1.1 Mainboard

  • ...t the computer by serial port, for parameter adjustment and query..
  • Position /speed/torque closed-loop, it can run at high speed without losing step. Easy to install and wire. The max printing speed can reach 150-180mm/S. Field-Oriented control, low noise, low vibration and low calorific. 4 Half bridge driver with 8 MOSFET, high operating efficiency. 14Bits magnetic encoder, high angle resolution..
  • Compatible with Gen L SGen L, SKR 2 / V1.4 Turbo BTT Octopus V1.1 Motherboard and other board which is seperated with drivers, that means drivers is not soldered onto the board.
  • Package: 1*MKS SERVO42C(include motor) + 1*Adapter board(MKS APT) + 1*60cm 6pin Data Cable . (User method, please check the links from the following description).
Check Stock

MKS GEN L V1.0 Controller Board 3D Printer Kit Mainboard Ramps1.4 Dual Extruder Touch for 3D Printer Accessories

  • Support a Variety of Stepper Drivers -- 2560 and Ramps 1.4 are integrated in the board, which avoids the problem of complicated connectors and malfunctioning. Support a variety of stepper drivers such as A4988, DRV8825, TMC2100, available to change the stepper drivers and motors as users like..
  • Reserve External Driver Signal -- available to connect external high-current driver to drive the 57 and 86 stepper motors. Use high-quality MOSFET, better cooling effect and more stable. Use specific power chip, support 12V-24V power input, and resolve t..
  • Use CH340 Serial Port Chip -- Stable and reliable filter circuit greatly reduces interference and avoids crashes as possible in the process of printing. Use CH340 serial port chip, more easily install the drive than 16U2..
  • Support 24V Input -- The heated bed current can be reduced to 1/4 at the same system power which effectively resolves the problem that the MOSFET of heated bed heats. Run Marlin firmware, the configuration is completely same as Ramps 1.4..
  • Compatible With -- Support Ramps 1.4, 2004LCD,12864LCD, TFT28 and TFT32. X-axis, Y-axis and Z-axis with different color terminal controls the stepper motors and endstops, which is convenient to wire..
Check Stock

SVS PB-2000 Pro 12\ Ported Subwoofer (Black Ash)

  • SVS Subwoofer DSP Smartphone App Available.
Check Stock

Planet Audio P10AW Amplified Car Subwoofer - 1000 Watts Low Profile 10 Inch Subwoofer Remote Subwoofer Control Great for Vehicles That Need Bass But Have Limited Space

  • Built-in Amplifier - A built-in 1000 Max watt amplifier powers the subwoofer.
  • Mosfet Power Supply - With a MOSFET power supply you get improved switching speeds, better performance with less power from the driver, lower....
  • Variable Low-Pass Filter - A low-pass filter is an electronic circuit that removes all the notes below the filter's frequency setting. You will use....
  • High Level Inputs - Speaker level inputs are commonly referred to as high-level inputs. It will be used to connect the P10AW to your factory radio or....
  • Low Level Inputs - Line level inputs, also known as RCA inputs or low-level inputs, use RCA interconnect cables to link the P10AW with the source....
Check Stock

Electric Scooter Adult, 5 Inch 24V 180W Motor, Brushless Motor, Low Noise, with Hall Sensor, Electric Scooter Motor Replacement Parts

  • 1. HIGH SPEED MOTOR: Powerful Brushless DC Motor Kits 2500W 60V, Rated Speed No-load 4400rpm, Max can be 5800rpm, Motor Rated current 45A..
  • 2. DIY KITS, Electric Go kart Motor, small size, high speed, BLDC mid-drive motor with T8F sprocket, scooter motor with mounting bracket is easier to install and carry, with air cooling holes..
  • 3. DC motor kit reverse design, BLDC kart motor can run clockwise or counterclockwise through motor reverse line or handlebar reverse switch, and has a 3-speed function, low speed 50%, medium speed 70-80%, The high-speed speed is 100% efficient, but do not let the motor run in reverse for a long time, which is not safe for the motor life..
  • 4. 24 Mosfet 45A brushless motor controller. This speed controller uses high-quality materials. This controller has Hall, 3-speed, reverse, throttle, charging, electronic brake, power lock, light functions, etc..
  • 5. List and application of electric scooter motor kits, BLDC motor, speed controller, handlebar throttle, pedal throttle, power lock key, T8F tooth plate ring, T8F chain, 3-speed switch. Suitable for electric scooters, electric bicycles, mini motorcycles, off-road vehicles, electric karts, bicycles, four-wheel drive vehicles, other DIY projects, etc..
Check Stock

RATTMMOTOR 400W Blushless CNC Air Cooled Spindle Motor ER8 12000RPM + 600W Blushless Spindle Motor Driver LCD Panel without Hall + 55mm Clamp Mount for CNC Router Milling Machine

  • 【Brussless Spindle Motor】Power: 400W.
  • Note: Please see clearly that this spindle motor output shaft is with ER8 collet,and output shaft is complete shaft, can't be exchanged to ER11, ER16....
  • 【Brussless Spindle Motor Driver】Maximum driver power: 600W.
  • Maximum driver motor running speed: 12000R/Min.
  • Brushless spindle driver（Model Name: NVBDL）is specialized for the ecomomic engraving machine,it matchs with the brushless DC motor. With the....
  • The users can take down the panel from the main driver and install it on the controller cabinet.By the panel,you can set the parameter,control motor....
Check Stock

2-Stroke Petrol Gas Motor Bicycle Engine Conversion Kit Bike Motor Modified Set Gas Motorized Bicycle Engine Kit for Motorized Bike 100cc

  • Kunray MY1020 Brushless Motor Features: Electric Brushless DC Motor, Aluminum Body, Full Copper Coil, Heat Resistant, Naturally Air Cooled, Low Noise High Quality More Long Life..
  • Motor Type: Brushless DC High Speed Motor, Voltage 48V, Power 2000W Max, Current 42A, Rated Speed 4300rpm/min, With T8F 11Teeth Sprocket Chainwheel..
  • About Controller: 48V 2000W 15 Mosfet 33A Brushless Motor Speed Controller, With Hall Sensor, E-Brake, 3Speed (Low Mid High Speed）, Reverse, Indicator Light And Power Lock Functions..
  • LCD Handlear Twist: 48V Lithium Battery LCD Screen Handlebar Throttle Twist Grips, With Battery Indicator, Ignition Lock, Twist Throttle Accelerator 3 in 1 Function Handlebar Grip, With High Quality Rubber Grips, More Comfortable..
  • Application For: Electric Scooter, Motorcycle, Ebike Bicycle, Go Karts, E-bike, Motorcycle, E Tricycle,Mid Drive Motor Kit, Complete Set,DIY Engine System, Cycling Part,And More.What You gGet: 1pcs Motor, 1pcs Controler, 1pair Throttle, And Manual..
Check Stock

HiLetgo 5pcs IRF520 MOSFET Driver Module MOSFET Button Drive for Arduino MCU ARM Raspberry PI

  • Output load current: 003c5A (1A above need to add heat sink).
  • Platform: Arduino, MCU, ARM, raspberry pie.
Check Stock

150 W 24 V 12 V DC Electric Motor zy6812 f Scooter Bike go-Kart or minibike New

  • ...ROTATION】- BLDC Go kart Motor Can Through the Motor Reversing Wire or Handlebar reverse Switch To Let The Motor Go Clockwise or Counterclockwise, And with 3 Speed Function, Low speed 50%, Mid speed 70-80%,High Speed 100% Efficiency, But Don’t let the Motor Run Reverse Long Time, is Not safe for Motor Life..
  • 【12Mosfet 30A Brushless Motor Controller】- The Motor Kit include 12MOS 30A Speed Controller, BLDC Motor Controller with high Quality Material, is enough for the Motor, with Hall 3-Speed Reverse Throttle Charging e-Braking Power lock Light Functions etc..
  • 【E-scooter Motor Kit List and Useful】- 1000W BLDC Motor, Speed Controller, Handlebar Twist Grip Throttle, Foot Throttle, Power lock key, T8F Tooth Plate Ring, T8F Chain, 3 speed Switch, is Good for Electric Scooter, E-bike, Mini Motorcycle,Dirt bike, Electric Go karts, Bicycle, Quad car，Other DIY project and more..
Check Stock

GeeekPi 5 Pack Geared Stepper Motor 28BYJ-48 5V Stepper Motor + Uln2003 Motor Driver Board + Dupont Wire Jumper Wires Ribbon Cables Compatible with Arduino

  • 5pcs Stepper motor and driver board compatible with arduinoIDE 2560 1280 DSP ARM PIC AVR STM32 Raspberry Pi..
  • Stepper motor with a standard interface could be connected with Driver Board easily.
  • A, B, C, D four-phase LED indicates the status of the stepper motor work..
  • 5 line 4 phase can be used for ordinary ULN2003 chip driver, connect to the 2 phase , support the development board, with convenient use, direct docking..
  • Package Includes:5 x Stepper Motor,5 x ULN2003AN Driver Board,30 x Female-to-female jump wire.
Check Stock