Intona 7055-C USB 3.0 SuperSpeed Isolator 1kVrms 20kV ESD Protection Supports Full Speed 12Mbps,High Speed hi-Speed 480Mbps and SuperSpeed 5Gbps
- No external power supply required, up to 500mA current on isolated side. External power can be connected to supply up to 2000mA current on isolated....
- Galvanic isolation to the USB bus, supports SuperSpeed 5Gbps, hi-speed 480Mbps, full speed 12Mbps and Low speed 12Mbps.
- 5kVrms signal and power isolation, Advanced ESD protection (20kV).
- Ultra-quiet power rail isolation for less noise in highly sensitive applications (LT3045).
Check StockReliance Controls Corporation TRC0603D Panel/Link
- Offers circuit breaker combination of 60A utility input and 30A generator input.
- Interlinked breakers keep generator isolated from utility at all times.
- TRC service entrance-rated, may be used as a main panel or a sub-panel.
- Has provisions for 12 to 20 branch circuits.
Check Stock
DaierTek 12V Bus Bar 6 x 5/16 M8 Terminal Studs 12 Volt Power Distribution Block with Cover Battery Bus Bar 12V - 48V Positive & Negative for Automotive Car Boat Solar System
- 【Product Name】- Battery bus bar terminal block, these busbars will come in pairs, include one positive bus bar (red one) and one negative bus bar (black one)..
- 【Terminals & Rating】- Each 12v power distribution block includes - 6 x M8 (5/16") terminal studs. This battery distribution block can handle voltage @ Max 300V AC, 48V DC, and continous amperage @ Max 130A AC, 150A DC..
- 【Round Corner Base】 - The 12v bus bar is unique round corner base design, which makes the battery terminal block unique and special, looks more extraordinary compared with other busbars..
- 【More Open Area Design Cover】 - The cover of this 12v power block will allow 180° wire lug installation and can meet variety kinds of installat methods of end terminals..
- 【Application】 - This marine power distribution block uses copper plates and stainless steel terminals as conductors, which enables the battery distribution block to work in extreme environment, suitable for automotive, car, marine, boat, etc..
Check StockReliance Controls Corporation TCA1006D Panel/Link 100-Amp Utility/60-Amp Generator Transfer Switch for Generators Up to 15,000 Watts
- Offers circuit breaker combinations of 60A-125A utility and 30A-125A generator.
- Interlinked breakers keep generator isolated from utility at all times.
- May be used as main panel for single load or to feed sub-panel.
- Features heavy-duty copper bus. MAX. UTILITY INPUT AMPS – 100.
Check StockHeart Horse Bus Bar Terminal Block 1/4 Power Stud Battery Junction Block Post Distribution Block Insulated with Cover DC 48V 150A for Auto Truck RV Boat 1/4 ,Red+Black
- WORKING RATING - Power stud size: 1/4".Maximum working voltage is DC 48V & up to 150 Amps.The battery bus bar is measured 1.77" x 1.69" x 1.4"..
- EASY TO USE - Each bus bar with a cover can prevent short circuits and is completely safe.The cable can be installed with a wrench without removing the cover..
- DURABLE & DEPENDABLE - The bus bar has good electrical conductivity and corrosion protection for durability.Terminal block's material is stainless steel, insulated base..
- EFFICIENTLY DISTRIBUTE POWER - With these power distribution block, you can organize your wiring cleanly and keep your environment clean and tidy..
- APPLICABILITY - Battery junction block is widely used in motorcycles, cars, trucks, RVs, etc..
Check StockHantek 1008C+ 8CH Automotive Diagnostic PC Oscilloscope 2.4MSa/s USB 2.0 bandwidth 100K Program Generator
- Free software upgrading constantly, higher cost performance.
- Standard equipped over 80 types of automotive measurement function (Ignition Action/The Sensor/Bus..
- USB 2.0 interface plug and play, and no need extra power supply..
- Support tablet PC, Support WIN10/ WIN8/WIN7..
- 4 isolated channels oscilloscope, 1GSa/s real time sampling rate, 2mV-10V/DIV high input sensitivity and large input range, 70MHz high bandwidth..
Check Stock
NESGLODUO Copper Flat Bar - Copper Bar Stock, Copper 110 Flat Bar, 0.24in x 1in x 12in
- 【Size】It is a solid bar of copper: 12''L x 1''W, 0.24'' thickness and weight is 14.11 ounces, no more no less, good size for the electrical project you're looking for..
- 【Material】Copper flat bar is made of copper, grade as C-110. It's thick enough and conducts heat well, so burn through is mitigated, if you need something to soak up heat this works well..
- 【Features】Easy to cut and drill, and work great for your intended use. My uncle easily fabd a bus bar system for his new X-S-3400s, good investment compared to custom machined pieces that are 3-4x the cost..
- 【Copper 110 Flat Bar】It would carry current with no issues and work well for your project such as make a bud bar for electrical project, or bus bar for battery connections..
- 【Application】Copper flat stock is suitable for various milling, craft, lathe, knife project, battery terminal L brackets, home solar battery bank, or others electrical engineering..
Check StockVictron Energy Lynx Power in Battery Connector
- The lynx power in module is used to connect batteries via an external fuse, It can be useful if you have multiple parallel strings.
- The Power In contains a negative and positive DC bus-bar with M8 bolts in which to connect batteries cables.
- It can take cables up to 22 mm in diameter through the bottom entry guides, and no limit via the two side connections.
- A modular DC bus bar, the Victron Lynx Power In is used to connect batteries to the Lynx DC distribution system.
- Incorrect installation can be hazardous, Please consult a licensed professional and follow all applicable electrical codes during installation.
Check Stock
Bopaodao Copper Bus Bar 3mm x 25mm x 5.91 inch / 150mm, 1Pcs C110 Pure Cu Copper Flat Buss Bar Stock
- 1Pcs c110 copper flat bus bar, 3mm x 25mm x 5.91 inch / 150mm, about T 1/8" x W 1".
- Copper flat bars are widely used for electrical applications for the high electrical and thermal conductivity. Due to its exceptional strength, ductility and corrosion resistance, copper flat bar is also typically used in architectural applications. Uses of copper flat bar include automotive, construction, machined components, roofing, industrial, electrical, fabrication, engineering, manufacturing, marine equipment, architecture industries.
- As a factory seller, we would like to accept any customization about the copper bar, including the length, drilling and bending or any other special needs, please contact us.
- The copper bar is made of 0.999 copper, which is the C110 Cu, we also provide tinned copper bar and Nickel-plated copper bar.
- Copper bars are also called copper bus bars or copper buss bars. They are made of copper and have rectangular or chamfered (rounded) rectangular cross-sections. (Nowadays, rounded copper bars are generally used to avoid tip discharge). The circuit plays the role of conveying current and connecting electrical equipment. Sometimes it can also be made as crafts or decorations.
Check Stock8 Terminal Bus Bar Terminal Block 10 Pack Brass Wire Screw Terminal for Car Boat Marine Ground Power Distribution Terminal Block
- Brass terminal grounding strip bus bar block with 8 screws & 2 Stud.
- High quality plastics base ensures great mechanical strength and durability.
- Use M4 screws to fix it in place through the two screw holes on both ends of the terminal.
- Widely used in power distribution cabinets, distribution boxes,mechanical equipment factories,electrical equipment factories,etc.
Check Stock12 Terminal Power Distribution Block Bus Bar - Made in USA (Original Cover)
- INCLUDES BOTH RED AND BLACK: With this 2 pack of 12 point bus bars, you will have plenty of connection points for both positive and negative wiring terminals..
- IDEAL FOR AUTO AND MARINE WIRING: Wire up to a dozen accessories with this 2 pack of bus bars. Each bus bar includes a cover and a terminal boot to insulate and protect connections for damage and corrosion..
- MADE IN THE USA: You can be sure you're getting high quality parts that are made right here in the USA. We are USA based, firefighter owned, and we stand behind our products..
- ORGANIZING MADE SIMPLE: With these bus bars you can finally organize your wiring so it doesn't look like a rats nest under the hood any more..
- 100% SATISFACTION GUARANTEED: If you have any issues with your order, contact us and we will make it right..
Check StockRecoil S2P-516 Busbar Dual 5/16” Studs and #8 Screw Terminal Power Distribution Block with Ring Terminals Pair Red & Black
- Product features: brass plate and stainless steel terminals as conductors have low resistance, conductivity and corrosion resistance..
- Parameters: maximum voltage: 300 V AC, 48 V DC, maximum continuous current: 130 A AC, 150 A DC..
- Scope of application: suitable for automobiles, trucks, ships, boats, yachts, etc..
- Material: The base is made of hard plastic, durable, and the protective cover is made of PC to prevent accidental electrical short circuit..
- Package: A red battery bus bar and a black battery bus bar..
Check StockSquare D - PK4GTACP 4 Terminal Ground Bar Kit, Silver
- High Quality Material -- The 4 position terminal bus bar is made of brass, polycarbonate shell, durable, with high strength, high hardness, wear resistance..
- Easy to Use -- Without protective cover, the 4 terminal bus bar can be used directly, easy to wire, convenient and fast..
- Product Dimension -- Total Size: 71 x 15 x 21mm / 2.79" x 0.6" x 0.83".
- Widely Usage -- The terminal block widely used in distribution boxes, distribution cabinets, other high pressure equipment and electrical equipment factories. Also can be used for trucks, cars, yachts, ship wiring, etc..
- Satisfactory After-Sales Service -- Uenhoy is devoted to providing high quality service. Please feel free to contact us if the item has any quality problem. Your satisfaction is our biggest power..
Check Stock
