10 Pieces No Clean Soldering Flux Pen and Solder Remover Wick, 0.1 Inch Wide and 59 Inch Long, Solder Braid Wick Liquid Solder Flux Pen for Electronics Welding Repair Tabbing Wire Maintenance
- Nice combination: you will get 5 no clean soldering flux pens and 5 solder remover wick sets, 10 in total, sufficient quantity, thoughtful combination, to meet daily use and replacement needs.
- Appropriate size: the no-clean solder wick is about 1.5 m/ 59 inches long and 2.5 mm/ 0.1 inches wide, and liquid flux brush flux pen is about 15 x 1.5 cm/ 6 x 0.6 inch, convenient to hold.
- Please check the size carefully before purchasing.
- Multiple reliable materials: these no-clean braided soldering wicks are made of quality copper wire, using nice weaving technology, which can enhance surface tension and absorb excess solder.
- And flux remover pen adopts quality material, non-leakage, flux safe and prevents you from being exposed to organic solvents.
- Practical tools: soft brush tip flux pen releases a moderate stream of liquid to clean components without spoiling the PCB copper foil or IC pins.
- Solder remover has good thermal conductivity and absorption, helping to reduce the risk of thermal spoiling to the board.
- Broad utilization: these flux pens and braided solder wicks can be applied in laboratories, computers, home repairs and to correct small PCB errors and through-hole joints, electronic soldering and much more, bringing a lot of convenience and effic....
Check StockFlux Off ChemtronicsES835B Flux Remover, Brush, 5 fl.oz.
- Price for: each cleaner type: flux remover cleaner applications: electrical/ electronics/ heat sinks/ pcbs.
- Dispensing method: brush applicator series: flux off volume: 5Fl.Oz. (Us) leaded process compatible: yes rohs compliant: yes.
Check StockKwik Clean Flux Cleaner 16 Oz
- Kwik-Clean flux remover doesn't need mixing or diluting.
- Just spray on Kwik-Clean when you're done soldering, then use paper towel to clean project.
- ALSO USE WITH PATINA: use either the same paper towel or a clean one to apply the patina..
- Mixing the Kwik-Clean with Patina gives added cleaning of the flux and a finer tone on the patina..
- After Patina is applied, clean again with Kwik-Clean. Polish as you normally would..
Check Stock
VIRALLOY No Clean Flux Solder Wick Braid Length 10ft Width 2.5mm Solder Copper Static Dissipative Bobbin Desoldering Wick Solder Remover Wick Desolder Electronic Components - Pack of 1
- Are you looking for a flux wick and an effective and efficient way to remove solder from your circuit boards? Look no further than the VIRALLOY No Clean Solder Flux Desoldering Braid!.
- Made from pure copper wires woven together with a no-clean flux formula, this solder braid wick is designed to absorb and remove solder from your circuit boards quickly and easily.
- The ergonomic design of the solder flux remover desoldering wick ensures that it will leave little to no residue after use, and the residues that are left behind are non-conductive and halide-free.
- Plus, the flux for soldering copper soldering wick is easy to use - simply place it over the area where you want to remove the solder and heat it up.
- The solder tape will absorb the solder, leaving your circuit board clean and free of unwanted solder. So why wait? Get the VIRALLOY No Clean Desolder Wick today and make desoldering a breeze!.
Check StockNo Clean Soldering Flux Pen and Solder Remover Wick, 0.1 Inch Wide and 59 Inch Long, Solder Braid Wick Liquid Solder Flux Pen for Electronics Welding Repair Tabbing Wire Maintenance (6 Pieces)
- ...made of reliable materials, no leaking and safe for protecting the flux, preventing you from touching the organic solvents.
- Practical tools: 10-ml solder flux pen with soft brush tip can release the liquid flow moderately, which can clean the components without harming the PCB board copper foil or IC pin.
- The solder remover wick features good thermal conductivity and absorption, useful to reduce the risk of thermal injury to the circuit boards.
- Wide applications: these flux pens and braided solder wicks can be applied for laboratory, computer, home repairs and correcting small PCB board errors and through-hole solder joints, electronics welding, etc., bringing a lot of convenience to your work and improving efficiency.
Check StockMG Chemicals 4140A Flux Remover for PC Boards, 1 Quart Bottle
- Use when a general-purpose zero residue flux remover is required.
- Removes rosin, non-rosin, and no clean fluxes as well as ionic and non-ionic residues..
- Suitable for use in food facilities as a Non-Food Chemical Canadian and NFS recognition letters available on request.
Check StockMG Chemicals - 406B-425G 406B Superwash Electronics Cleaner, 425g (14 oz) Aerosol Can
- Suitable for Use in Food Facilities as a Non-Food ChemicalCanadian and NFS recognition letters available on request.
- Applications: Flux and contaminant remover for printed circuit boards.
Check Stock
3 Pieces No Clean Soldering Flux Pen Rosin Solder Flux Pen for Electronics Tabbing Wiring Solder, Welding Maintenance of PCB Board, No
- Quantity and size: package contains 3 pieces soldering flux pens, enough quantity for meeting your daily usage and replacement.
- Each soldering flux pen measures approx. 5.6 inches in length.
- Safe to use: these flux pens are made of quality material, no leak and safe to use.
- Low solids content and quality of the activator system results in practically no residue left on the assembly after soldering.
- No residue will interfere with electrical testing.
- Useful and practical: no clean soldering flux pen is a novel tool for rework and repair welding.
- It allows controlled application of flux, thereby removing dirt in the flux bottle.
- Pen tip of 10 ml with practical designed felt tip.
- The solid content is low and there is almost no residue.
- Wide application: rosin solder flux pen is suitable for automotive, computer, work for rework, and through hole solder joints.
- It is lightweight and would not occupy too much space, suitable pocket size to carry.
- How to use: before the first time use, you should press the pen tip 1 - 2 times for releasing air, then use no clean solder flux pen to remove the oxidizing wax.
- After that, you can use the alcohol to clean the pen.
Check StockSolder Smoker Absorber Remover Fume Extractor Smoke Prevention Absorber DIY Working Fan Soldering with spare Carbon filter
- Solder Smoke Absorber/Fume Remover/Smoke Extractor Prevention Absorber DIY Working Fan for Soldering Station..
- It adopt the high performance fan with low noise, and the suction is strongThe structure is simple. The replacement of the activated carbon filter....
- Optimized 3000 RPM high suction fan is low noise and allows you to remove fumes 5-6 inches away. Long-lasting working time for over 50,000 hours..
- Comes with 5 Active carbon filters. The filter is made of special foam with refined activated carbon, which has high suction and flux absorption....
- It's a good helper for mobile phone maintenance, great for electronics, arts and crafts, stained glass work, soldering station work..
Check Stock
BEEYUIHF Rosin Soldering Paste Flux, Solder Paste Flux, Flux for Soldering, For SMD PCB Soldering & Repair, Electrical Soldering Rosin Flux (1.76oz/50g)
- BEEYUIHF #7150 Soldering Paste Net weight: (1.76oz/50g) Rosin Solder Paste Flux, made of no acid, Lead-Free, No-Clean, soldering flux paste which is not easy to dump. Rosin Soldering Paste,High Purity,Good helper for repairing and welding..
- Soldering Flux Paste Feature: No corrosion, high intensity joint, good immersion, good insulation, good soldering properties, smooth welding surface..
- Flux for soldering application: Maintenance drag soldering, BGA planting tin, maintenance desoldering, electronic components soldering, mobile phone maintenance, mobile phone chip maintenance, LED lighting, home appliance maintenance.Have strong oxide removal effect to gold-copper alloy substrate and wire..
- #7150 paste flux features: Lead-free, halogen-free, acid-free, no cleaning, less residue, easy to tin, less smoke, help soldering firm, make soldering fluidity better, slightly yellow paste..
- Solder Flux also a good helper for maintenance enginee. Rosin soldering flux paste metal can packaging, High-quality aluminum box packaging, not easy to break..
Check StockKOTTO Solder Smoke Absorber Remover Fume Extractor Smoke Prevention Absorber DIY Working Fan for Soldering Station with 5 Pack Carbon Filter
- Solder Smoke Absorber/Fume Remover/Smoke Extractor Prevention Absorber DIY Working Fan for Soldering Station.
- 0.4 inch thick activated carbon filter absorbs and captures fumes from solder, flux, chemicals, gases and helps to prevent dissipation into the room..
- Optimized 3000 RPM high suction fan is low noise and allows you to remove fumes 5-6 inches away. 4 non-slip heavy duty rubber feet anchors the unit to....
- Easy to replace filter, Includes one replacement filter. Working temperature: -20℃～60℃, Power consumption: 120V, 30W (50 / 60Hz)..
- US based customer support, 30 days full satisfaction no question asked return period..
Check StockSolder Flux (56.6 grms)| flux paste | rosin solder | electrical flux paste | solder paste no clean | flux paste for soldering | rosen flux paste | solder flux electrical | flux paste for electronics
- [Enought Quantity] : This rosin solder flux comes in 1 jar of 56 grams of soldering flux..
- [Non Corrosive]: This non acid flux is not conductive in dry conditions and has good insulation. Is not corrosive to metal substances such as circuit boards..
- [Oxidation Resistance] : This solder flux for electronics Anti-oxidation effect on soldering iron head of gold-copper alloy substrate. Solder flux for semi-solid, not easy to dump or waste..
- [Strong Capability]: This rosin paste flux is suitable for welding instruments, gold, copper, tin, iron and other metals. Ideal for electronic welding, repair and rework..
Check Stock100PCS-Flux Core Welding Wire for Aluminum,Low Temperature Flux Cored Welding Rod Make Repair Aluminum Radiator,Ideal for Both Beginners And Professionals Alike,752°F(400°C) Melting Point.(13"/1.6mm)
- Simplified welding process: Flux-cored rods have a low melting point and do not require solder powder, making them easy to use even for beginners..
- High-quality aluminum brazing: The aluminum brazing rods come with flux already included, ensuring a durable and long-lasting bond..
- Only for Welding Aluminum - 100Pcs(13"/1.6mm)Flux Core Welding Wire are Suitable for Welding or Surfacing Welding Aluminum, Aluminum Alloy, Aluminum-Magnesium Alloy and Other White Metals,752°F(400°C )Melting Point..
- Flux Cored Aluminum Welding Rod Make Repair Aluminum Radiator Easily： Flux Core Welding Wire is Commonly Used for Repairing Aluminum Radiators in Automobiles, Motorcycles, Air Conditioners, and Refrigerators, Making it A Versatile Tool to Have In Your Toolbox..
Check Stock
