Reviews Fluid Solenoid Valve

Surwit 15810-RAA-A03 VTEC Solenoid Spool Valve Assembly with Oil Pressure Switch & Gasket Compatible with Honda Accord Element CR-V 2.4L Civic Acura RSX 2.0L Part# 15810-RAA-A01 15810-PPA-A01

  • The VTEC system provides the engine with valve timing optimized for both low and high RPM operations. The VTEC solenoid actually allows oil to flow to the internal galleries of the overhead camshaft. This means that the housing of the solenoid is holding back full engine oil pressure. A spool solenoid valve can direct the flow of hydraulic fluid. The valve is made up of spools that rotate or slide to block and open channels in a hydraulic system..
  • This VTEC Solenoid Spool Valve Fits for 2003 - 2011 Honda Element 2.4L, 2002 - 2009 Honda CR-V 2.4L, 2003 - 2007 Honda Accord 2.4L, 2002 - 2006 Acura RSX 2.0L, 2002 - 2005 Honda Civic 2.0L..
  • Customers can find the product you need accurately according to the OE number. OE part number: 917-224, 15810RAAA03, 15810RAAA02, 15810-RAA-A01, 15810PPAA01, 15810PNEG01, 15810-RAA-A03, 917224, 15810-PNE-G01, 15810-RAA-A02..
  • While a VTEC solenoid rarely goes bad, problems with VTEC not engaging properly are extremely common. Most of the time incorrect wiring is to blame, but occasionally something even smaller is the culprit. When a solenoid is bad, may mean the solenoid's plunger is either mechanically stuck in a closed position and therefore always making contact which may eventually cause the starter motor to burn its w....
Check Stock

9L2Z7G391A Automatic Transmission Control Solenoid Pack Assembly Fits for Ford Explorer 2003-2010 Mustang 05-10 Thunderbird 04-05 Mercury Mountaineer 03-10 Lincoln Aviator 03-05 LS 04-06 5R55S 5R55W

  • Transmission solenoids are one of your automatic transmission’s many critical components. A transmission solenoid is an electro-mechanical component “valve” used to control the flow of transmission fluid in the transmission, and they open and close as per the electrical signals they receive from your vehicle’s engine or transmission control unit, which pulls its data from a series of speed sensors in the engine..
  • Modern automatic transmissions use pressurized hydraulic fluid to change gears. Every time a gear change is required, the car’s computer activates a transmission solenoid, which directs transmission fluid into the valve body to engage the correct gear. If one of these electro-mechanical valves fail, then all sorts of transmission problems can ensue..
  • This Automatic Transmission Control Solenoid Fits For the Following Vehicles: 2003-2010 Ford Explorer 6 Cyl 4.0L, 8 Cyl 4.6L, 8 Cyl 4.6L.
  • 2007-2010 Ford Explorer Sport Trac 6 Cyl 4.0L , 8 Cyl 4.6L.
  • 2005-2010 Ford Mustang 6 Cyl 4.0 , 8 Cyl 4.6L, 8 Cyl 5.4L.
  • 2004-2006 Lincoln LS 6 Cyl 3.0L, 8 Cyl 3.9L.
  • 2003-2010 Mercury Mountaineer 6 Cyl 4.0L, 8 Cyl 4.6L, 8 Cyl 4.6L..
  • Customers can find the product you need accurat....
Check Stock

mistcooling 250 PSI Misting Pump

  • 250 psi pump quiet operation 35Db solenoid valve – Controls flow of water in the pump in built filter – helps protect your misting nozzles built in water by pass self-priming.
  • Nickel-plated brass button series With stainless-steel Orifice Standard 10/24-inch thread 0. 012-inch Orifice Rust-resistant fixed impeller pin 0. 014 GPM Flow per Nozzle.
  • Maximum inlet pressure: 100 psi Minimum inlet pressure: self- priming. Maximum outlet pressure: 250 psi (depends on line length and numbers of nozzles) maximum flow: 0. 9 GPM full load Amps. 110V AC: 0. 7 amps 12V DC: 4. 0 amps Voltage: 110V-220V AC/ 12V DC (refer manufacturing label on the pump) noise level: 40 dB. Maximum fluid temperature: for room temperature/ cold water applications only.
  • Max pressure 250 psi Available in 110 V, 220 V & 12 VDC Durable Rust Proof Enclosure Thermal Safety Switch Oil-less Pumps may generate heat, motor manufacturer have installed built-in thermal safety switch to improve the longevity of pumps Standard pump inlet: 3/8-inch push lock Fitting. Standard Pump outlet: ¼ inch Push-lock fitting. Max pressure 250 psi 110 V AC.
  • 1. Solenoid Valve Solenoid valve controls the flow of the water in to the pump. You may leave the inlet water source on at all the time. Water will enter th....
Check Stock

28250-P6H-024 Transmission Dual Linear Shift Solenoid Gasket For Honda Acura Accord Odyssey Prelude Pilot 1998-2003 Replace 28250P6H024

  • ✔【Ideal replacement】：A bad solenoid cannot effectively control the flow of transmission fluid, causing delays or unexpected friction between the shift gears. This solenoid is comparable in fit, form and function to the original part, exactly OEM design to replace your defective solenoid.
  • ✔【Compatible with】Fits for 1998-2002 Honda Accord 4 Cyl, 1998-2007 Accord 6 Cyl, 1998-2006 Odyssey, 2003 2004 2005 2006 2007 Pilot, 97 98 99 00 01 Prelude | 1998-1999 Acura 2.3 CL, 1998-1999 Acura 3.0 CL, 2001-2003 Acura 3.2 CL, 1999-2003 Acura 3.2 TL, 01-02 Acura MDX.Please check the part number to compare whether it suits your car before you purchase..
  • ✔【Transmission Shift Solenoid Replace OEM】 : 28250-P6H-024, 28250P6H024..
  • ✔Package include: 1 x Linear Solenoid + 1pcs gasket +3pcs O-rings.
  • It is consisting of a spring loaded plunger wrapped with a coil of wire, and design to open or close valves in the valve body to permit transmission fluid to enter..
  • ✔【Product Warranty】: 12-Month Warranty: If the torque converter solenoid fails, stops working or any other problems, you can rely on our service of carefree REPLACEMENT or REFUND..
Check Stock

KIMISS Car Transmission Solenoid Valve 28250-PRP-013 for Honda and Acura Models Transmission AT Clutch Pressure Control Linear Solenoid Valve 13 * 7cm / 5.1 * 2.8in

  • 【Main Function】This Transmission Solenoid Control Valve is consisting of a spring loaded plunger wrapped with a coil of wire, designed to open or close valves in the valve body to allow transmission fluid to enter..
  • 【Specially for for for for Honda Models】Our Transmission Linear is Specially designed to fit For Acura & for for for Honda vehicles. Please check the size and compatibility carefully before placing an order..
  • 【Professional OE Level】The prossional car transmission shift solenoid valve is an important vehicle electrical system executive control part with higher stablity and reliability, meeting or exceed OEM standards. The replaceable OE number for reference: 28250-PRP-013..
  • 【High Quality Construction】Made of high grade iron, the AT Clutch Solenoid Valve is of strong strength, high temperature and resistance for long time use..
  • 【Easy Installation】Plug and play. Easy to install without extra adjustment, perfectly match the original car. Convenient for assembly and disassemble.If you have any questions, please feel free to firstly check product description for a good solution..
Check Stock

AOMAG 3/8" Electric Solenoid Valve 12V DC, VITON Gasket, Air, Gas, Fuel Normally Closed

  • VITON GASKET- Viton is a space age material that is very chemically inert. As such, it is commonly used with gasoline, kerosine and other organic solvents. Some companies sell solenoid valves with NBR gasket and advertise gasoline use. DO NOT USE NBR gasket for gasoline (it will corrode the gasket and can cause serious gasoline leak and accident or fire). If you intend on using a valve for gasoline, use only VITON gasket..
  • ISO/OEM/ODM/CE and1 year warranty. DIRECT ACTING and Normally Closed Valve (N.C.) - The solenoid’s magnetic field with directly moves the plunger and close the orifice for any fluid or gas flow. Only opens while energized..
  • -NEW- Re-engineered low power coil with up to 50% less heat generation. The valve starts as 19W and as it heat up to operating temperature power reduces to approx. 10-13W..
  • 1/4" NPT (USA National Pipe Thread). Commonly used standard pipe thread in US...
  • PLEASE NOTE: This valve is NOT a continuous duty valve and should NOT be in continuous use for more than 6 hours in a single cycle.
  • to do so will shorten the life of the valve and may ca....
Check Stock

3/4\ Brass Electric Solenoid Valve,  110V Air Valve Normally Colsed for Water Air Gas Fuel Oil 2W-200-20

  • High quality 3/4inch Brass Electric Solenoid Valve： Constructed of industrial grade brass, this valve is corrosion resistant, more conducive for welding, optimal for higher temperature projects, and can be used with gasoline, diesel fuel, kerosene oil, natural gas, air etc.  .
  • Normally closed electric solenoid valve: 2 way solenoid valve,Model: 2W-200-20.
  •   3/4" NPT port,   Working temperature range: -5 ℃~80 ℃.
  •  Operating  Pressure: MIN.0kg/cm - MAX.10kg/com  .
  • This solenoid valve 110v was manufactured with a VITON seal,two-way inlet and outlet ports with standard female thread NPT connectionsm and heat and oil resistant Viton gasket.   .
  • Applicable Irrigation Controls (garden, Farm,etc.), Liquid Controls ( Pipeline, Artificial River Etc. and Air Controls ( Lab, Factory, Etc.) -3/4 inch Brass Electric Solenoid Valve Also known as110v solenoid valve,electric solenoid water valve,brass liquid solenoid valve. .
  • This valve comes with a ONE YEAR WARRANTY. If the valve does become defective within the first year of purchase, We will gladly replace it..
Check Stock

1/4\ NPT Brass Electric Solenoid Valve 12V DC Normally Closed VITON (Standard USA Pipe Thread). Solid Brass, Direct Acting, Viton Gasket Solenoid Valve by AOMAG

  • VITON GASKET- Viton is a space age material that is very chemically inert. As such, it is commonly used with gasoline, kerosine and other organic solvents. Some companies sell solenoid valves with NBR gasket and advertise gasoline use. DO NOT USE NBR gasket for gasoline (it will corrode the gasket and can cause serious gasoline leak and accident or fire). If you intend on using a valve for gasoline, use only VITON gasket..
  • ISO/OEM/ODM/CE and1 year warranty. DIRECT ACTING and Normally Closed Valve (N.C.) - The solenoid’s magnetic field with directly moves the plunger and close the orifice for any fluid or gas flow. Only opens while energized..
  • -NEW- Re-engineered low power coil with up to 50% less heat generation. The valve starts as 19W and as it heat up to operating temperature power reduces to approx. 10-13W..
  • 1/4" NPT (USA National Pipe Thread). Commonly used standard pipe thread in US...
  • PLEASE NOTE: This valve is NOT a continuous duty valve and should NOT be in continuous use for more than 6 hours in a single cycle.
  • to do so will shorten the life of the valve and may cause the core of the valve to burn out. If you need a continuous duty valve for your project please search for our AOMAG Motorized Ball Valves..
Check Stock

uxcell Pulse Solenoid Valve G1/2 DC3.6V Copper Male Thread Valves with Filter

  • This solenoid valve is basic automated components that electromagnetically control fluids..
  • Flow Direction: Unidirectional (Follow the Arrow on Valve Body).
  • Solenoid type magnetic field makes the valve reach higher pressure, which greatly improves the flow of the passed medium..
  • Replacement solenoid valve for induction fittings. Replace the bad work solenoid valve for machine..
Check Stock

DJ TRANS PARTS – 45RFE 545RFE 68RFE Solenoid Pack – Quality and Tested OEM product – Compatible with Dodge, Chrysler, & Jeep – Years 2004 and Up | Warranty Included with Purchase (RENEWED)

  • COMPATIBLE WITH – Here is a list of products that is compatible with this item. Feel free to google the part numbers as well to ensure it fits your vehicle. Compatible with Chrysler 300 2010-11 Valve Body Solenoid, Chrysler 300C 2010-11 Valve Body, Chrysler Aspen 2007-09 Valve Body Solenoid, Dodge Avenger 2010-11 Valve Body, Dodge Challenger 2010-11 Valve Body, Fit for Dodge Charger 2010-11 Valve Body Solenoid, Dodge Dakota 2004-11 Valve Body Solenoid, Dodge, Durango 2012 Valve Body Solenoid..
  • PRODUCT IS REMANUFACTURED OEM PART– All of DJ Trans Parts items are original OEM products. That being said, they are not brand new but refurbished. They are remanufactured and tested to ensure they work. This means you are getting the actual transmission, valve body, solenoid kit, etc. that your car needs. You can ensure our products will work with OEM parts..
  • PART NUMBERS - Here are the related part numbers of this item - 5RFE 545RFE 68RFE Transmission Solenoid Block Pack.
  • INSTALLATION VIDEOS ONLINE - Searching related installation video on the internet will be recommended. You can find these videos on Google and searching the part numbers online. We recommend to always wear eye protection and start with installation tools..
Check Stock

1/4inch DC 12V 2 Way Normally Closed Electric Solenoid Air Valve

  • .WIC Valve is compatible with SMC valves. Has two holes in the bottom and can be mounted in any position..
  • .2ACK Series valve is a Zero differential solenoid valve which can be operated at 0 PSI (Vacuum)..
  • .Comes with a ED 100% encapsulated coil which suitable to operate in continuous service and constant energized..
  • .This solenoid valve has one G1/4" inch DN8 inlet and one G1/4" inch DN8 outlet port. Valve stays close when the coil is de-energized- and it opens when energized..
  • .1/4inch DC 12V 2 Way Normally Closed Pneumatic Aluminum Electric Solenoid Air Valve WIC Valve 2ACK series 2-way normally closed solenoid valve is to control On/Off of air and inert gas..
Check Stock

Power Speed Steering Valve Related Solenoid A2214600184 Fit for Benz C‑Class (W204) 2008‑2014

  • ...ce the OEM number as a reference: A2214600184, which is made strictly according to the original materials and specifications, and is completely suitable..
  • ☀☀ Applicable to: Fit for Benz C-Class (W204) 2008-2014, direct replacement, (see detailed description below)..
  • ☀☀ Professional Manufacturing: The steering solenoid valve is professionally manufactured with high precision and high reliability. The solenoid valve is durable and stable in quality, and can be used with confidence..
  • ☀☀ Easy to Install: This speed sensing steering solenoid valve is easy to install, remove and replace the old valve. No need for complicated tools, professional manufacturing ensures that we can provide you with higher quality products, which you can buy easily..
  • ☀☀ Standard Specifications: It meets strict quality control standards and is reliable in use. Manufactured according to original specifications. Manufacture in strict accordance with factory quality control standards..
  • ☀☀ Professional Manufacturing: The steering solenoid valve is professionally manufactured with high precision and high reliability. The solenoid valve is durable and stabl....
Check Stock

1 Brass Electric Solenoid Valve 110V AC NPT Normally Open Air Gas Water Viton

  • 1" NPT THREAD- Commonly used standard pipe thread in U.S...
  • SOLID BRASS -This valve's body is made of solid brass (very corrosion resistant material)..
  • NORMALLY OPEN- The solenoid's magnetic field will directly move the plunger and close the orifice for any fluid or gas flow, while energized..
  • FLOW DIRECTION- The arrow indicates the flow direction (horizontal mounting please)..
  • VITON GASKET- Viton is space age material that is very chemically inert. As such it is commonly used with gasoline, kerosine and other organic solvents. Some companies sell solenoid valves with NBR gasket and advertise gasoline use. DO NOT USE NBR gasket for gasoline (it will corrode the gasket and can cause serious gasoline leak and accident)..
Check Stock