Reviews Avr Pic Programmer

Weewooday 15 Pieces 5V Relay Module 1- Channel Relay Control Boards with Optocoupler Isolation High and Low Level Trigger Expansion Board

  • Relay module: this relay board supports high and low level trigger and can be controlled by any 5V digital output of the microcontroller.
  • Parameter details: maximum load of normally open interface: AC 250v/ 10A, DC 30v/ 10A, trigger current is 5mA.
  • The 5v relay control board adopts SMD optocoupler isolation, which has strong driving ability and stable performance.
  • Practical design: with fault-tolerant design, the relay module will not operate even if the control line is disconnected.
  • All interfaces can be provided through directly connected terminal s since the humanized interface design, it is very convenient to use.
  • High compatibility: the relay module can be directly controlled by the 5V logic signal provided by the microcontroller, suitable for 8051, Raspberry Pi, PIC, DSP, ARM, AVR, MSP430, TTL logic, etc..
  • Wide application: this 5V relay board can be applied with Raspberry/ CNC machine/ ARM/ PIC/ AVR/ MCU/ PS4 and more.
Check Stock

SainSmart 8-Channel Relay Module

  • 5V 8-Channel Relay interface board, and each one needs 15-20mA Driver Current.
  • Equipped with high-current relay, AC250V 10A.
  • Standard interface that can be controlled directly by microcontroller (Arduino , 8051, AVR, PIC, DSP, ARM, ARM, MSP432, TTL logic).
  • Indication LED's for Relay output status.
Check Stock

SainSmart 16-Channel 12V Relay Module Board for Arduino DSP AVR PIC ARM

  • 12V 16-Channel Relay interface board, and each one needs 15-20mA Driver Current.
  • Equipped with high-current relay, AC250V 10A.
  • Standard interface that can be controlled directly by microcontroller (Arduino , 8051, AVR, PIC, DSP, ARM, ARM, MSP433, TTL logic).
  • Indication LED's for Relay output status.
Check Stock

Tegg 2PCS Flat Ribbon Cable 2.54mm Pitch 2 Row 10 Pin Female to Female Wires IDC Ribbon Connector 1m/ 3.3Ft

  • Product name: Flat Ribbon Cable. Type: 2 Row 10 Pin..
  • Cable long: 1m/ 39.4 Inches.Cable width: 12.5mm / 0.49 Inches..
  • Withstand voltage: 300 V.Temperature: 105 Degree Centigrade..
  • Used for most Atmel AVR JTAG debugger, system programmer, Isp download, etc..
Check Stock

Xiuxin 2pcs 5V 8 Channel Relay Module Board for Arduino PIC AVR DSP ARM

  • 2pcs/lot 8 Channel relay module board, Working voltage: 5V.
  • This board is for Arduino PIC AVR DSP ARM.
  • Support all single-chip microcomputer control,Industrial circle,PLC controller,Household intelligent control.
  • Relay output maximum contact is AC250V 10A and DC30V 10A.
  • Widely used for all MCU control, industrial sector, PLC control, smart home control..
Check Stock

WINGONEER Universal IC Adapter Socket LQFP TQFP QFP32 to DIP28 and TQFP32 to DIP32 IC Adapters for ATMEL AVR Chips

  • Applicable for all ATMEL AVR series QFP32 chips.
  • Applicable for all programmer: TL866CS/A/SP300U/ALL-100GANG/ALL-11 series/LT-48 series/SuperPRO series/TOP series .......
  • Support chips: Atmega48 Atmega8 Atmega88 Atmega168....
  • Package Include: 1 x QFP32 to DIP28 Adapter.
Check Stock

MybotOnline 5 Sets Stepper Motor 28BYJ-48 ULN2003 5V Stepper Motor + ULN2003 Driver Board

  • Stepper motor with a standard interface, motor diameter: 1.1", wire length: 9.05".
  • A, B, C, D four-phase LED indicates the status of stepper motor work.
  • Compatible with ArduinoIDE UNOR3 MEGA 2560 1280 DSP ARM PIC AVR STM32 Raspberry Pi.
  • Gift: 1x 10-pin male to female multicolor breadboard jumper wires，each cable length: 7.87"(20 cm).
  • Packing in a box: 5 sets Uln2003 stepper motor + driver board + 10 pin jumper wire.
Check Stock

WinnerEco 5pcs 1 Channel DC 5V Relay Switch Module for Raspberry Pi ARM AVR

  • 1-channel relay interface board which can be controlled directly by a wide range of microcontrollers. Controllers includes AVR, PIC, ARM, PLC, etc..
  • Relay output maximum contact is AC110V ~ AC250V 10A and DC30V 10A..
  • Standard interface can be directly connected with microcontrollers..
  • Red working status indicator for power on indication.Green working status indicator for relay the switch..
  • It can control various appliances and other equipments with large current.Widely used for all MCU control, industrial sector, PLC control, smart home control..
Check Stock

1.8 inch SPI TFT LCD Display Module for ST7735 128x160 51/AVR/STM32/ARM 8/16 bit

  • This is a new 1.8 inch serial SPI color display module.
  • Support analog SPI and hardware SPI. SPI serial, less I/O port need.
  • Designed with one socket for sd card and PCB adapter for LCD.
  • The LCD display module can be driven by 8051 / AVR / PIC /ARM/STM32.
  • The 4D systems lcd display can be driven with at least four IO.
Check Stock

sb components Air Monitoring Breakout, Air Monitor Module for Raspberry Pi, Beaglebone, Arduino, STM32, PIC, AVR, ARM, etc.

  • Air Monitoring breakout, air monitoring module by SB Components.
  • It provide the level of quantity of the suspended particulates with their mass.
  • It has a powerful and hi-tech PMSA003 sensor that provides the information of suspended particulate matter.
  • It communicates via UART(serial) with the standby current ≤200 Microampere(μA) of the sensor.
  • Compatible with Raspberry Pi, Beaglebone, Arduino, STM32, PIC, AVR, ARM, etc..
Check Stock

ALMOCN 6Pcs DC 5V 1 Channel Relay Module With Optocoupler Isolation Support High or Low Level Trigger

  • The Relay Board Maximum load: AC 250V/10A, DC 30V/10A.
  • Using SMD optocoupler isolation, strong driving capability, stable performance..
  • Can be set high or low level trigger with jumper cap, to meet the demand of more trigger applications..
  • Fault-tolerant design, even if the control line is broken, the relay will not move..
  • Wide Application,The relay board works well with ARM /PIC /AVR /MCU/Raspberry/CNC machine/ PS4 etc..
Check Stock

LED LCD Universal TV Backlight Constant Current Backlight Lamp Driver Board Boost Step Up Module 10.8-24V to 15-80V 14-37 Inch

  • This is a new 1.8 inch serial SPI color display module.
  • Support analog SPI and hardware SPI. SPI serial, less I/O port need.
  • Designed with one socket for sd card and PCB adapter for LCD.
  • It can be driven by 8051 / AVR / PIC /ARM/STM32.
Check Stock

5v Relay Board Relay Module 1 Channel Opto-Isolated High or Low Level Trigger

  • 【1 Channel Relay Module】- This Relay Board provides a single relay that can be controlled by any 5V digital output from your microcontroller..
  • 【Main Specification】- Peak Load of NO Connector: AC125~250V/10A, DC28~30V/10A.
  • 【Adopted SMD Optocoupler Isolation】- The isolation circuit prevent damages to I / O port by relay switch current..
  • 【Wide Application】- These 5v relay board works well with ARM /PIC /AVR /MCU/Raspberry/CNC machine/ PS4 etc..
  • 【Humanization Design On Interfaces】- All interfaces can be directly wired out through the terminals..
Check Stock