Reviews Xlpe Power Cable

HEATIT JHSF 60-feet 120V Self Regulating Pre-assembled Pipe Heating Cable

  • JHSF doesn't work unless the ambient temperature is below 37F/3 degree C. Please test the cable in a cold environment..
  • Suitable for use on plastic and metal water pipes.( including inlet pipe,drain pipe, sewer , palm tree frost protection etc). Self regulating heating cable output will adjust automatically based on the ambient temperature at each point along the cable..
  • Pre-assembled, easy to install. Including grounded plug with light, built in thermostat(turn the cable 37F on 50F off) and instructions. 120 volt, 3 watts/ft at 50 degrees F. Protect pipes up to 2" in diameter. Can be used by straight, spiral and overlap..
  • ETL approved. 2 ft 18/3 cold lead with plug. The lowest installation temperature of this heating cable is -10 degree C. Tough XLPE as inner insulation and weather resistant PE (high-low temperature) as out jacket. Ingress Protection 65..
  • Testing the cable before the installation. Uncoil the cable, plug in the heating cable. Normally you can feel the slight warm on the heating cable in few minutes..
Check Stock

HEATIT JHSF 120-feet 120V Self Regulating Pre-assembled Pipe Heating Cable

  • JHSF doesn't work unless the ambient temperature is below 37F/3 degree C. Please test the cable in a cold environment..
  • Suitable for use on plastic and metal water pipes.( including inlet pipe,drain pipe, sewer , palm tree frost protection etc). Self regulating heating cable output will adjust automatically based on the ambient temperature at each point along the cable..
  • Pre-assembled, easy to install. Including grounded plug with light, built in thermostat(turn the cable 37F on 50F off) and instructions. 120 volt, 3 watts/ft at 50 degrees F. Protect pipes up to 2" in diameter. Can be used by straight, spiral and overlap..
  • ETL approved. 2 ft 18/3 cold lead with plug. The lowest installation temperature of this heating cable is -10 degree C. Tough XLPE as inner insulation and weather resistant PE (high-low temperature) as out jacket. Ingress Protection 65..
  • Testing the cable before the installation. Uncoil the cable, plug in the heating cable. Normally you can feel the slight warm on the heating cable in few minutes..
Check Stock

250' Nassau 4-4-4-4 Tulsa Quadruplex Aluminum Conductor Underground Direct Burial URD Cable 600V

  • Conductor: Compact stranded 8000 series aluminum alloy.
  • Insulation: Crosslinked polyethylene (XLPE). Type USE- 2.
  • Conductor Identification: Black phase conductors. Triple yellow striped neutral.
  • Construction: Multiplexed cable conductors with a left hand lay in triplex (3 conductor) assembly.
  • Industry Standards: UL Standard 854. ICEA S-66-524. REA approved.
Check Stock

HEATIT HIRD 80 feet 5 Watts Per Foot Roof & Gutter Snow De-Icing Cable

  • Tough XLPE as inner insulation and weather resistant PVC (high-low temperature) as out jacket. 100% screen rate with the Aluminum foil and tinned copper braid. More safe and more healthy..
  • Both CSA and ETL approved. 6 ft 18/3 cold lead with plug . Pre-assembled, ready to install, no maintenance required. Easy instruction manual, clips and spacers are included..
  • Designed to prevent ice build up, known as ice dams, from forming on roofs and in gutters and downspouts. Protect your roof from damage and leaking, keep the water flowing in gutter & downspouts..
  • Used for Metal or plastic gutters/downspouts, Inclined roofs Roofs with noncombustible shingles (Ex.: asphalt shingles) that meet national building codes. Different lengths are available.
  • Suitable for most roof and gutter configurations..
  • Testing the cable before the installation.Uncoil the heat cable completely so it does not touch, cross over or overlap on itself. Do not plug in the cable until it has been completely uncoiled. Plug cable in, and in approximately 5 minutes, you should feel slightly warm to the touch. Then unplug the cable..
Check Stock

HEATIT HIRD 30 feet 5 Watts Per Foot Roof & Gutter Snow De-Icing Cable

  • Tough XLPE as inner insulation and weather resistant PVC (high-low temperature) as out jacket. 100% screen rate with the Aluminum foil and tinned....
  • Both CSA and ETL approved. 6 ft 18/3 cold lead with plug . Pre-assembled, ready to install, no maintenance required. Easy instruction manual, clips....
  • Designed to prevent ice build up, known as ice dams, from forming on roofs and in gutters and downspouts. Protect your roof from damage and leaking,....
  • Used for Metal or plastic gutters/downspouts, Inclined roofs Roofs with noncombustible shingles (Ex.: asphalt shingles) that meet national building....
  • Testing the cable before the installation.Uncoil the heat cable completely so it does not touch, cross over or overlap on itself. Do not plug in the....
Check Stock

HEATIT HIRD 200 feet 5 Watts Per Foot Roof & Gutter Snow De-Icing Cable

  • Tough XLPE as inner insulation and weather resistant PVC (high-low temperature) as out jacket. 100% screen rate with the Aluminum foil and tinned copper braid. More safe and more healthy. Three year limited warranty- If you are not completely satisfied with HEATIT heating cable, please don’t hesitate to contact us in any time..
  • Both CSA and ETL approved. 6 ft 18/3 cold lead with plug . Pre-assembled, ready to install, no maintenance required. Easy instruction manual, clips and spacers are included..
  • Designed to prevent ice build up, known as ice dams, from forming on roofs and in gutters and downspouts. Protect your roof from damage and leaking, keep the water flowing in gutter & downspouts..
  • Used for Metal or plastic gutters/downspouts, Inclined roofs Roofs with noncombustible shingles (Ex.: asphalt shingles) that meet national building codes. Different lengths are available.
  • Suitable for most roof and gutter configurations..
  • Testing the cable before the installation.Uncoil the heat cable completely so it does not touch, cross over or overlap on itself. Do not plug in the cable until it has been completely uncoiled. Plug cable in, and in approximately 5 minutes, you should feel slightly warm to the touch. Then unplug the cable..
Check Stock

Heat it HIRD 20 feet Roof Gutter De-Icing Cable

  • ... or ice (“melt water”) to drain from the roof to the ground..
  • Used for Metal or plastic gutters/downspouts, Inclined roofs Roofs with noncombustible shingles (Ex.: asphalt shingles) that meet national building codes. Different lengths are available.
  • Suitable for most roof and gutter configurations. HIRD cable cannot be used on slate, stone, metal and ceramic roofs..
  • Test the cable before installation. Uncoil the heat cable completely so it does not touch, cross over or overlap on itself. Do not plug in the cable until it has been completely uncoiled. Plug cable in, and in approximately few minutes, it should feel slightly warm to the touch. Then unplug the cable..
  • Both CSA and ETL approved. 6 ft 18/3 cold lead with plug.
  • 5 watts/ft. Pre-assembled, ready to install, no maintenance required.
  • Easy instruction manual, clips and spacers are included..
  • Tough XLPE as inner insulation and weather resistant PVC (high-low temperature) as out jacket. 100% screen rate with the Aluminum foil and tinned copper braid. More safe and more healthy. Three year limited warranty- If you are not completely satisfied with HEATIT heating cable, please don’t hesitate to contact us in any time..
Check Stock

HEATIT HISD 18-feet Pipe Heating Cable with Built-in Thermostat

  • Use for water filled plastic (including PEX) or metal pipes. Not use for anything else, like empty water pipes, fuel lines, hoses, gutters, steam lines and so on. Two year limited quality . If you are not completely satisfied with HEATIT heating cable, please don’t hesitate to contact our customer service in any time, we’ll try our best to solve your issues..
  • Pre-assembled easy to install. Including grounded plug with light, built in thermostat, and instructions. Easy to install and use. 120 volt, 7 watts/ft. Built in thermostat to turn the cable 37F on 50F off. Energy saving. 100% screen rate with the Aluminum foil and tinned copper braid..
  • Both CSA and ETL approved. Industrial grade heat shrinkage tube for connection. Tough XLPE as inner insulation and weather resistant PVC (high-low temperature) as out jacket..
  • Maximum 1/2 in fiberglass insulation was used over the heating cable for lower temperature protection. Pipes must be at least 3 feet and at least 3/8” and less than 1 1/2” in. diameter. No crossing. No spiral. No overlap itself. Only straight..
  • Testing the cable before the installation. Uncoil the cable, plug in the heating cable and then put the thermostat part of the cable into an ice bucket for few minutes. When t....
Check Stock

HEATIT HISD 15-feet Pipe Heating Cable with Built-in Thermostat

  • Use for water filled plastic (including PEX) or metal pipes. Not use for anything else, like empty water pipes, fuel lines, hoses, gutters, steam lines and so on. Two year limited quality . If you are not completely satisfied with HEATIT heating cable, please don’t hesitate to contact our customer service in any time, we’ll try our best to solve your issues..
  • Pre-assembled easy to install. Including grounded plug with light, built in thermostat, and instructions. Easy to install and use. 120 volt, 7 watts/ft. Built in thermostat to turn the cable 37F on 50F off. Energy saving. 100% screen rate with the Aluminum foil and tinned copper braid..
  • Both CSA and ETL approved. Industrial grade heat shrinkage tube for connection. Tough XLPE as inner insulation and weather resistant PVC (high-low temperature) as out jacket..
  • Maximum 1/2 in fiberglass insulation was used over the heating cable for lower temperature protection. Pipes must be at least 3 feet and at least 3/8” and less than 1 1/2” in. diameter. No crossing. No spiral. No overlap itself. Only straight..
  • Testing the cable before the installation. Uncoil the cable, plug in the heating cable and then put the thermostat part of the cable into an ice bucket for few minutes. When t....
Check Stock

HEATIT HISD 12-feet Pipe Heating with Built-in Thermostat, Black

  • Use for water filled plastic (including PEX) or metal pipes. Not use for anything else, like empty water pipes, fuel lines, hoses, gutters, steam lines and so on. Two year limited quality . If you are not completely satisfied with HEATIT heating cable, please don’t hesitate to contact our customer service in any time, we’ll try our best to solve your issues..
  • Pre-assembled easy to install. Including grounded plug with light, built in thermostat, and instructions. Easy to install and use. 120 volt, 7 watts/ft. Built in thermostat to turn the cable 37F on 50F off. Only use 5 amps or less of electricity. Energy saving. 100% screen rate with the Aluminum foil and tinned copper braid..
  • Both CSA and ETL approved. Industrial grade heat shrinkage tube for connection. Tough XLPE as inner insulation and weather resistant PVC (high-low temperature) as out jacket..
  • Maximum 1/2 in fiberglass insulation was used over the heating cable for lower temperature protection. Pipes must be at least 3 feet and at least 3/8” and less than 1 1/2” in. diameter. No crossing. No spiral. No overlap itself. Only straight..
  • Testing the cable before the installation. Uncoil the cable, plug in the heating cable and then put the thermostat part of the cable in....
Check Stock

HEATIT HISD 3-feet Pipe Heating with Built-in Thermostat, Black

  • Use for water filled plastic (including PEX) or metal pipes. Not use for anything else, like empty water pipes, fuel lines, hoses, gutters, steam lines and so on. Two year limited quality . If you are not completely satisfied with HEATIT heating cable, please don’t hesitate to contact our customer service in any time, we’ll try our best to solve your issues..
  • Pre-assembled easy to install. Including grounded plug with light, built in thermostat, and instructions. Easy to install and use. 120 volt, 7 watts/ft. Built in thermostat to turn the cable 37F on 50F off. Only use 5 amps or less of electricity. Energy saving. 100% screen rate with the Aluminum foil and tinned copper braid..
  • Both CSA and ETL approved. Industrial grade heat shrinkage tube for connection. Tough XLPE as inner insulation and weather resistant PVC (high-low temperature) as out jacket..
  • Maximum 1/2 in fiberglass insulation was used over the heating cable for lower temperature protection. Pipes must be at least 3 feet and at least 3/8” and less than 1 1/2” in. diameter. No crossing. No spiral. No overlap itself. Only straight..
  • Testing the cable before the installation. Uncoil the cable, plug in the heating cable and then put the thermostat part of the cable in....
Check Stock

HEATIT JHSF 12-feet 120V Self Regulating Pre-assembled Pipe Heating Cable

  • JHSF doesn’t work unless the ambient temperature is below 37F/3 degree C. Please test the cable in a cold environment. HEATIT is registered Trademark by zhukeshi(We didn’t authorize other sellers in Amazon.com)..
  • Suitable for use on plastic and metal water pipes.( including inlet pipe,drain pipe, sewer , palm tree frost protection etc). Self regulating heating cable output will adjust automatically based on the ambient temperature at each point along the cable. No worry about the overheat risk. More Safe. Can be used by straight, spiral and overlap. More functional..
  • Pre-assembled, easy to install. Including grounded plug with light, built in thermostat(turn the cable 37F on 50F off), and instructions. 120 volt, 3 watts/ft at 50 degrees F. Energy-efficient. Protect pipes up to 2″ in diameter. For a better freeze protection, at least 1/2 inch thick insulation material is recommended, especially for extremely cold weather..
  • ETL approved. 2 ft 18/3 cold lead with plug. Industrial grade heat shrinkage tube for connection.The lowest installation temperature of this heating cable is -10 degree C. Tough XLPE as inner insulation and weather resistant PE (high-low temperature) as out jacket. Ingress Protection 65. Durable.
Check Stock

HEATIT JHSF 6-feet 120V Self Regulating Pre-assembled Pipe Heating Cable

  • JHSF doesn’t work unless the ambient temperature is below 37F/3 degree C. Please test the cable in a cold environment. HEATIT is registered Trademark by zhukeshi(We didn’t authorize other sellers in Amazon.com)..
  • Suitable for use on plastic and metal water pipes.( including inlet pipe,drain pipe, sewer , palm tree frost protection etc). Self regulating heating cable output will adjust automatically based on the ambient temperature at each point along the cable. No worry about the overheat risk. More Safe. Can be used by straight, spiral and overlap. More functional..
  • Pre-assembled, easy to install. Including grounded plug with light, built in thermostat(turn the cable 37F on 50F off), and instructions. 120 volt, 3 watts/ft at 50 degrees F. Energy-efficient. Protect pipes up to 2″ in diameter. For a better freeze protection, at least 1/2 inch thick insulation material is recommended, especially for extremely cold weather..
  • ETL approved. 2 ft 18/3 cold lead with plug. Industrial grade heat shrinkage tube for connection.The lowest installation temperature of this heating cable is -10 degree C. Tough XLPE as inner insulation and weather resistant PE (high-low temperature) as out jacket. Ingress Protection 65. Durable.
Check Stock