Reviews Welding Clamp Set

ABN Butt Welding Clamps - 8 Piece Small Welding Clamps Auto Body Panel Clamps for Edge to Edge Welding

  • [Perfectly Align Panels] Use the ABN Welding Square Clamp Set to pinch sheet metal panels level to each other.
  • While these metal clamps hold panels edge to edge with a 1mm gap, you can quickly weld the sheets together.
  • [Fits your Project] Each welding square tool pipe clamp can extend the clamp block to provide a .4-inch (1cm) tall gap.
  • Fits 3/16-inch to 26 gauge sheet metal materials.
  • [Easy to Use] Loosen the winged nut from the alignment screw then wedge two panels across from each other between the square body and the clamp block.
  • Tighten the winged nut to ensure a secure hold.
  • Use all 8 clamps for larger projects, then joint weld between them.
  • [Built to Last] Panel welding clamps are constructed of zinc-plated steel to ensure maximum durability and strength while resisting rust.
  • [Contents] Welding accessories set includes 8 welding corner square welder clamps.
  • Used to make precision butt welds and edge-to-edge welds for patch repairs in floors, wings, door skins, fabricating, and re-skinning projects.
Check Stock

WeldingCity 100-ft 2-AWG USA-made Heavy Duty Welding Cable Highly Flexible Durable EPDM Rubber Jacket 600V -50C-105C Black

  • USA-made 2 AWG heavy duty welding cable (EPDM rubber jacketed black cover) for use where maximum flexibility and resistance to cuts, tears, abrasion is required. Max volt 600V, -50C to 105C. Resistant to chemicals, oils, and acids and is also weather, ozone and sunlight resistant. Available welding cable sets: welding cable only.
  • cable set with terminal lugs and cable set with Dinse connectors..
  • Welding Cable Set With Terminal Lug includes: 2-AWG USA-made welding cable at selected length, one 300-amp stick electrode holder with accessory kit, one 300-amp ground clamp and three zinc-plated copper terminal lugs (1/2" stud hole)..
  • Welding Cable Set With Dinse Plug includes: 2-AWG USA-made welding cable at selected length, one 300-amp stick electrode holder with accessory kit, one 300-amp ground clamp, one zinc-plated copper terminal lug (1/2" stud hole) and two Dinse-type 35-50mm male connectors..
  • Heavy duty 300-amp stick electrode holder with strong jaw spring.
  • both upper and lower jaws made of copper (brass) with increased operator comfort. Zinc-plated steel 300-amp work clamp with strong spring, copper plated jaw, copper braid, copper plated hex screw for secured cable connection. Dinse-type twist-lock cable connector (male) with heat and oil resis....
Check Stock

Toolly Butt Welding Clamps - Small Welding Clamps Auto Body Panel Clamps for Edge to Edge Welding, Pack of 16 (1 inch x 1 inch x 2.1inch)

  • 【Product Purpose】Butt welding clamps set includes 16 welding corner square welder clamps, which can be used to make precision butt welds and edge-to-edge welds for patch repairs in floors, wings, door skins, fabricating, and re-skinning projects. They are good accessories to help you to find the location quickly in repair work..
  • 【Perfectly Align Panels】Using the Toolly Welding Square Clamp Set to pinch sheet metal panels level to each other.
  • When these metal clamps hold panels edge-to-edge with a gap of 1mm, you can quickly weld the sheets together..
  • 【Applicable Types】Each welding square tool pipe clamp can extend the clamp block to provide a 4-inch (1cm) tall gap.
  • Fits 3/16-inch to 26 gauge sheet metal materials..
  • 【Easy To Use】Loosen the winged nut from the alignment screw and then wedge two panels across from each other between the square body and the clamp block.
  • Tighten the winged nut to make sure a firm fixation.
  • Use all 16 clamps for larger projects, then perform joint welding between them..
  • 【High Quality & Portable】These panel welding clamps are made of high quality matrial, which makes sure the durability and strength.
  • meanwhile, these clamps are in small size can be easily placed in your pocket or welding equipment tool bag..
Check Stock

4 Pcs Locking C Clamp Set Locking Pliers with Fixed and Swivel Pads 6 Inch 9 Inch 11 Inch Metal Tools Welding Clamps for Home Farm

  • Locking C Clamp Set: 4 welding clamps are included, including 1 piece of 6 inch locking C clamp with fixed pad, 1 piece of 6 inch locking C clamp with swivel pad, 1 piece of 9 inch locking C clamp swivel pad and 1 piece of 11 inch locking C clamp with swivel pad, meeting your everyday needs.
  • Sturdy to Use: the jaw is forged with carbon steel as a whole, featuring with good toughness.
  • The handle of stamped steel plate, clamping object without deforming.
  • The heat treatment adjusting rod is easy to adjust the suitable size.
  • Additionally, the serrated jaw of locking C clamp has a strong clamping force.
  • Adjustable Design: the locking C clamp is easy to adjust to the appropriate clamping size because of the fine tuning knob design.
  • The quick release handle is convenient and labor saving.
  • Moreover, the spring provides good tensile force.
  • Firm Locking: welding clamps are mainly applied for clamping parts for riveting, welding, grinding and other processing.
  • Since the jaw can generate large clamping force, the clamped objects will not loosen.
  • Essential Supplies: in daily life, the lock C clamp is suitable for electricians and welders to clamp welding boards.
  • And woodworkers can use this metal tool to quickly clamp boards or frames.
Check Stock

4 Inch Heavy Duty Malleable C Clamps for Woodworking Welding Automotive Carpentry Building 4 Pack

  • 4 Inch C Clamp: Use this set of 4 c clamps for woodworking, metal work, welding, automotive, or furniture manufacturing.
  • Multi-Use: The welding face clamp has a sliding handle that will help reduce hand fatigue while ensuring a strong, secure hold on any wood and metals.
  • Clamping Range: Our c clamp set features a screw and thread design that allows you to freely control the clamping range to your needs.
  • Dimensions: Each 4 inch c clamp measures 8 x 4 x 0.6 inches in length.
  • Reliable Quality: The black c clamps for metal working are made from malleable iron that won’t easily break after long-term use.
Check Stock

300A 16㎡ Copper Clad Aluminum Cable Dinse 10-25 Connector Plug Welding Leads Assembly Set 9.8ft Welding Electrode Holder and 6.5ft Stick Plier Ground Clamp for ARC Stick MMA Mini Welding Rod Welder

  • ✨ This kind of Welding Electrode Holder is made of Copper Clad Aluminum clamp head and special insulation heat-resistant material. High temperature resistance, non-conductive, suitable for long-term use.
  • ✨ The Welding Ground Clamp is also suitable for stick,tig,mig or cut welding.Features wide grip jaws to ensure a firm connection.Grounds work can be welded to a good electrical ground earth.
  • ✨ 9.8ft long Welding Electrode Holder with cable and 6.5ft long Welding Ground Clamp with cable. 16㎡cable,Dinse 10-25 connector.*-*Please check connector size in the picture and compare with your welder´s Connector/Receptacle to make sure it fits*-*.
  • ✨ This Welding Leads Assembly Set has a strong current(300A).It is not easy to scald with copper forging.Also,the welding electrode rod in the Electrode Holder is not easy to fall off for the high strength Multi-angle occlusion.You will receive a ready to use fully assembled lead, no tools required.
  • ✨ This set of welding accessories have a common advantage: Copper guide, Copper Clad Aluminum wire, stable and durable, thick handle, high-quality upper and lower jaws, not easy to oxidize with heat, strong bite force.
Check Stock

200A Magnetic Welding Ground Clamp, 200A On/off Adjustable Magnetic Welding Ground Clamp Rare Earth Switchable Magnet Welding Holder,Grounding Magnet Connector

  • Magnetic Welding Ground Clamp: Made of high quality iron, durable in use. High strength and hardness. Fast set up and grounds instantly. Applicable to clamp both flat and round workpieces..
  • 200A Magnetic Ground Clamp: Magnet Strength Pull Force 30 kg, Simple to connect, ground wire of welding machine. Simply place on clean surface and turn on then start welding. Stays clean because magnetic field turns completely off..
  • Easy to Use: Strong grip on flat or round iron surfaces. The on/off control makes the metal dust fall off without cleaning, which is convenient and simple to use..
  • Package Included:1 x Welding Ground Clamp.
  • Warm Tips: Make sure that the grounding device is in the off state when it is not in contactwith the ferromagnetic material. It can be freely controlled to open and close. When the ferromagnetic material is opened and connected, it will produce sudden and powerful suction. Do not use welding grounding to lift or transport materials..
Check Stock

Toolly 16 Pack Butt Welding Clamps - Small Welding Clamps Auto Body Panel Clamps for Edge to Edge Welding

  • Butt Welding Clamps includes 16 welding corner square welder clamps.
  • Used to make precision butt welds and edge-to-edge welds for patch repairs in floors, wings, door skins, fabricating, and re-skinning projects.
  • Use the Toolly Welding Square Clamp Set to pinch sheet metal panels level to each other.
  • While these metal clamps hold panels edge to edge with a 1mm gap, you can quickly weld the sheets together.
  • Each welding square tool pipe clamp can extend the clamp block to provide a .4-inch (1cm) tall gap.
  • Fits 3/16-inch to 26 gauge sheet metal materials.
  • Loosen the winged nut from the alignment screw then wedge two panels across from each other between the square body and the clamp block.
  • Tighten the winged nut to ensure a secure hold.
  • Use all 16 clamps for larger projects, then joint weld between them.
Check Stock

Butt Welding Clamps, Sturdy Durable 16pcs Butt Welding Clamps ,for Sheet Metal Auto Car Truck Door Skin Panel, for Precision Butt Welding and Edge to Edge Welding(16pcs)

  • High-quality and durable:This set of clips has excellent performance in precision butt welding and edge-to-edge welding. The butt welding tongs are made of galvanized steel, rust-proof, heat-resistant and durable. The smooth metal surface prevents rust, is not easy to deform, and has a long service life..
  • Professional welding clamp tools:Each welding square tool tube clamp can extend the clamp block, leaving a 0.040 inch (1cm) gap between the panel and the edge welding. Suitable for straight or curved plates. The minimum gap of the welding plate is about 1 mm, which can be adjusted to a farther position as needed..
  • Good performance: These clips can be completely fixed before butt welding, leaving only a small gap to make the weld completely penetrate. This is an ideal choice for professionals engaged in sheet metal body repair..
  • Professional use:Sheet metal welding tongs are designed for welding operations. Very suitable for welding cracked metal floors, automotive sheet metal surfaces, door skins or prefabricated panels assembled in re-skinning projects. These clips can fix panels of any shape anywhere..
  • Easy to use:After spot welding the two panels together, remove the wing nut release device and toggle, just remove the fixture from the work befor....
Check Stock

ATPEAM Butt Welding Clamp | Pack of 16 Small Welding Clamps Auto Body Panel Clamps for Edge to Edge Welding

  • Premium Material: Panel welding clamps are constructed of zinc-plated steel to ensure maximum durability and strength while resisting rust.
  • Fits your Project: Each welding square tool pipe clamp can extend the clamp block to provide a .4-inch (1cm) tall gap.
  • Fits 3/16-inch to 26 gauge sheet metal materials.
  • Good performance: These small welding clips can be completely fixed before butt welding, leaving only a small gap to make the weld completely penetrate. This is an ideal choice for professionals engaged in sheet metal body repair..
  • Easy to Use: Loosen the winged nut from the alignment screw then wedge two panels across from each other between the square body and the clamp block.
  • Tighten the winged nut to ensure a secure hold.
  • Use all 16 clamps for larger projects, then joint weld between them.
  • Package Included: Welding accessories set includes 16 welding corner square welder clamps.
  • Used to make precision butt welds and edge-to-edge welds for patch repairs in floors, wings, door skins, fabricating, and re-skinning projects.
Check Stock

DCT C Clamps for Woodworking Welding Clamps Locking Pliers Set 3-Piece Wood Clamp Set 11in and 6in Swivel Tip

  • ...R PROJECT: Use the DCT | 3-Piece Hand Tools C Clamp Set to grip your project without slippage.
  • This locking C clamp set includes 1 clamp with regular pads and 2 clamps with swivel pads for damage-free automotive work with auto body panels, most home improvement and repair, woodworking wood joints projects, and some welding applications.
  • 3 CLAMPS, 2 SIZES: 11-inch clamp with swivel pad tips for securing medium to large work, approximate 1-inch (2.5cm) maximum opening, 0.9-inch x 1.1-inch (2.3cm x 2.8cm) flat clamp face size.
  • 6-inch clamp with swivel pad tips for small to medium pieces, approximate 0.7-inch (1.7cm) maximum opening, 0.7-inch x 0.8-inch (1.8cm x 2cm) flat clamp face size.
  • 6-inch clamp with regular tips, approximate 1.3-inch (3.2cm) maximum opening, 0.4-inch x 0.3-inch (0.9cm x 0.7cm) rounded clamp face size.
  • BUILT TO LAST: Constructed from nickel-plated carbon steel for maximum strength and longevity.
  • Hex key adjustment screw for adjusting to the correct pressure.
  • Classic guarded trigger release for maximum locking force and keeps pliers locked securely.
  • Unlike other C-type clamps, these C clamp locking pliers are designed with the handle opposite the clamp to allow access to tight spaces.
  • Each wood working clamp comes lightly pre-oiled fo....
Check Stock

Oumefar Welding Electrode Clamp, 400 Amp Twist Type Holder Welding Electrode Rod Holder Welding Electrode Twist Type Full Copper (Black)

  • COMPACT DESIGN ---- Welding electrode holders have strict quality control and quality assurance, compact design, small size, and the handle conforms to ergonomic design, and the work experience is more labor-saving..
  • FAST AND CONVENIENT ---- Type Holder Welding Tool has excellent workmanship and practicality, 400~500A universal, welding electrode clamp is more convenient to choose welding rod, which will help you to weld materials quickly and conveniently..
  • USED FOR ---- The welding Twist Type Full Copper holder adopts advanced technology and exquisite craftsmanship, and welding electrode clamp is not hot for long-term welding. Welding electrode clamp is used as a welding electrode holder for various rod electrodes..
  • WELDING ELECTRODE CLAMP ---- Type Holder Welding Tool have 1 x electrode holder, 1 x hex wrench, 1 x spacer and 1 x spacer post in the package. You can choose from black and yellow to meet your needs..
  • SERVICE ---- We launch products that meet your needs, and you will get our 100% problem-free guarantee. Customer's smile is our first goal,if you have any question,....
Check Stock

WYNNsky Magnetic Welding Support Ground Clamp, 2pcs Set, Single and Double Welding Head, Copper Tail

  • Design: This magnetic clamp attaches easily to any smooth metal surface, flat or curved. It holds on tightly, without budging easily. Super suction magnet at the bottom, large suction power, long-lasting magnetism..
  • Application: This device serves as the ground point, which you can take with you anywhere. Simply tack this onto a convenient spot, hook up your safety wire and you're ready to weld..
  • Material: The welding magnet head adopts high quality material, durable and solid. Has brass tail has good welding stability, durable, anti-rust, has good performance and long service life..
  • Advantage: This magnetic clamp is handy to have in such situations. You can stick in on a car body and not have to damage the paint. The clamp can also be attached to metal poles, struts, railings or the welding table..
  • Including 1pc Single Head Magnetic Welding Ground Clamp.
  • 1pc Double Head Magnetic Welding Ground Clamp.
  • 1pc Copper Tail Welding Stability Clamps..
Check Stock