Reviews Waveform Display Meter

Dorhea DSO 150 Digital Oscilloscope Kit with Protection Box Color 2.4″ TFT LCD Full Assembled with Allicator Chip Cable Probe and Case Cover, Sensitivity for Oscilloscope DIY Kit

  • DSO 150 kit is an upgrade to the popular DSO138 scope kit. Contains a 2.4″””” color TFT LCD (320×240) display and optical encoder for navigation..
  • Auto/normal/single trigger modes, easy to capture the moment waveform. use 9V DC power charger (NOT Included)..
  • Convenient to capture the instantaneous waveform. 2.4-inch color TFT display, waveform parameter digital display include: Frequency, period, pulse width, duty ratio, MAX./MIN./AVG./Peak-Peak/virtual values and effective value. with secondary development on the basis, can be changed to voltmeter, data loggers..
  • Used for secondary development on the basis of this kit, it can be changed to millivoltmeter, data loggers with instructions, easy to install and operate..
  • waveform storage function: waveform will not lose when save/tune out the waveform/shutdown waveform, available rising or falling edge trigger, observable previous waveform before trigger (negative delay), can freeze waveform display at any time (HOLD function)..
Check Stock

DSO 138 Oscilloscope Kit Open Source with Probe 2.4

  • This kit uses ARM Cortex-M3 processor (STM32F103C8), and includes a 2.4-inch color TFT display screen, can be used as ARM test development board.Can freeze at any time waveform display (HOLD function).Comes 1Hz /3.3V square wave test signal source..
  • With automatic, regular and one-shot modes, easy to capture the moment waveform.Available rising or falling edge trigger.Observable previous trigger waveform (negative delay)..
  • With waveform parameter digital display, including frequency, period, pulse width, duty ratio, MAX./MIN./AVG./Peak-Peak/virtual values.Waveform storage function: will not lose the waveform after power off..
  • Partially open-sourced,the MCU has been programmed.The oscilloscope circuit boards components are pre-soldered, no need soldered by yourself.The case is unassembled and requires assembly..
  • Adjustable vertical displacement,and with instructions,which increase the likelihood of adding different features or developing new applications on the hardware for users..
Check Stock

WisTek DSO Shell Oscilloscope Full Assembled with BNC-Clip Cable Probe, 1MSa/s, 0-200KHz, 5mV/div Sensitivity and 2.4-inch Color TFT Display

  • DC Power and Probe are Not included. With Automatic mode, conventional mode and single trigger mode. Included 10:1 BNC probe and use 9V DC power charger (NOT Included), Convenient to capture the instantaneous waveform. With secondary development on the basis, can be changed to voltmeter, data loggers. 2.4-inch color TFT display.
  • Waveform parameter digital display include: Frequency, period, pulse width, duty ratio, MAX./MIN./AVG./Peak-Peak/virtual values and effective value.
  • Adopts ARM Cortex-M3 processor (STM32F103C8).
  • Rising or falling edge trigger are available, also the trigger level position and vertical displacement are adjustable. Short-circuit and open-circuit detection to find out the soldering error.
  • Observable the previous waveform before trigger (negative delay). Freeze waveform display at any time (HOLD function). Come with instructions, easy to install and operate.
  • Waveform storage function: Waveform will not lose when save/tune out the waveform/shutdown waveform. Test signal source with 1KHz /3.3V square wave. Pls contact us if have any quality issue and need support, will reply within 24hours, refund or replace with a new one.
Check Stock

Oscilloscope Multimeter, 2-in-1 Intelligent Digital Scope Meter Multimeter, Professional LED Handheld Oscilloscope Multimeter with 200ksps A/D Automatic Waveform Capture Function

  • DSO 138 oscilloscope circuit boards components are pre-soldered, no need soldered by yourself..
  • DSO 138 Mini Oscilloscope uses ARM Cortex-M3 processor (STM32F103C8), and includes a 2.4-inch color TFT display screen, can be used as ARM test development board.Can freeze at any time waveform display (HOLD function)..
  • DSO 138 Oscilloscope With automatic, regular and one-shot modes, easy to capture the moment waveform.Available rising or falling edge trigger.Observable previous trigger waveform (negative delay)..
  • This oscilloscope With waveform parameter digital display, including frequency, period, pulse width, duty ratio, MAX./MIN./AVG./Peak-Peak/virtual values.Waveform storage function: will not lose the waveform after power off..
  • Adjustable vertical displacement and with instructions,which increase the likelihood of adding different features or developing new applications on the hardware for users..
Check Stock

DSO138 Oscilloscope, DIY Mini Oscilloscope DSO-138, 2.4″ TFT 1MSPS Digital Oscilloscope Kit Handheld Pocket Sized 13803K (Welded Version)

  • 【WIDELY USE】DSO 138 Oscilloscope With automatic, regular and one-shot modes, easy to capture the moment waveform.Available rising or falling edge trigger.Observable previous trigger waveform (negative delay). Let you effectively observe and measure signal waveforms in many occasions such as audio, video synchronization, low-frequency switching power supply, infrared receiving and transmitting..
  • 【EXCELLENT QUALITY】This oscilloscope With waveform parameter digital display, including frequency, period, pulse width, duty ratio, MAX./MIN./AVG./Peak-Peak/virtual values.Waveform storage function: will not lose the waveform after power off..
  • 【PRODUCT FEATURE】DSO 138 Mini Oscilloscope uses ARM Cortex-M3 processor (STM32F103C8), and includes a 2.4-inch color TFT display screen, can be used as ARM test development board.Can freeze at any time waveform display (HOLD function)..
  • 【NO NEED SOLDERED】DSO 138 oscilloscope circuit boards components are pre-soldered, no need soldered by yourself..
  • 【DIY DESIGN】Adjustable vertical displacement and with instructions,which increase the likelihood of adding different features or developing new applications on the hardware for users..
Check Stock

UNI-T UT210E Pro + UTG932, Digital Clamp Meter, Function Generator Arbitrary Waveform 30MHz 200MSa/s

  • Higher waveform capture rate Up to 200,000wfms/s waveform capture rate, greatly improving the capture pole The ability of low-probability events can more intuitively observe signal jitter and glitches, 256-level grayscale and color difference fluorescent display effect, waveform changes are visible..
  • Rich data measurement functions Support 34 kinds of automatic measurement parameter functions, Support Zoom, Math, statistics and advanced calculation functions..
  • Independent time base adjustable The time base of each channel is independently adjustable, and it has 4 windows display at the same time, which is convenient for users to observe four signals with large frequency differences.
  • Possess rich triggering and decoding functions, as well as waveform recording and playback functions Support bus decoding: I²C, SPI (only four channels), USB, CAN, optional: RS232/UART. Up to 100,000 frames waveform record,Record the waveform changes, replay the waveform conveniently, and analyze the fault.
  • UPO3254E 250MHz 4 2.5 GSa/s 70 Mpts 200000 wfms/s UPO3154E 150MHz 4 2.5 GSa/s 70 Mpts 200000 wfms/s.
Check Stock

Red Lion Controls/N-Tron PAXDP000 Pax Dual Process Input Meter, Red Display, AC Powered

  • This unit measures AC/DC voltage and current, resistance, capacitance, frequency, transistor hFE and temperature.
  • True RMS meter provides accurate readings when measuring linear or nonlinear loads where the current or voltage has an undistorted or distorted waveform.
  • Large LCD, High contrast, Wide visual angle LCD display, white backlight.
  • Dual-display: Main display 80000, Vice-display 80000, analog bar 23 segments.
  • 50 kinds of measuring function, with basicly DCV, ACV, DCA, ACA, W(Omega), CAP, Hz, TEMP, diode and continuity measuring function.
  • Standard function generator: 18 kinds of frequency, 1%-99% Duty cycle, 1800 pcs wave output.
  • Single analyzed: (AC+DC) measuring synchronous, (AC+Hz) measuring synchronous, (DC+dBm) measuring synchronous, (dBm+Hz) measuring synchronous, (Hz+Duty) measuring synchronous displaying synchronous.
  • AC measuring adopt High accuracy RMS, Widely measuring and AC+DC function, can measuring the accuracy virtual value of AC by any wave.
Check Stock

DSO 138 DIY Oscilloscope Kit Opening Source 2.4″ TFT 1MSPS Pocket-Size Digital Oscilloscope Kit with DIY Parts & Probe, Handheld Pocket Electronic Learning Set, Assembled Vision (Welded)

  • This DSO 138 oscilloscope circuit boards components are pre-soldered, no need soldered by yourself..
  • This oscilloscope board uses ARM Cortex-M3 processor (STM32F103C8), and includes a 2.4-inch color TFT display screen, can be used as ARM test development board.Can freeze at any time waveform display (HOLD function).Comes 1Hz /3.3V square wave test signal source..
  • 2.4″ Oscilloscope with automatic, regular and one-shot modes, easy to capture the moment waveform.Available rising or falling edge trigger.Observable previous trigger waveform (negative delay)..
  • 2.4 inch TFT handheld pocket-size digital oscilloscope with waveform parameter digital display, including frequency, period, pulse width, duty ratio, MAX./MIN./AVG./Peak-Peak/virtual values.Waveform storage function: will not lose the waveform after power off..
  • Partially open-sourced,the MCU has been programmed, adjustable vertical displacement,and with instructions,which increase the likelihood of adding different features or developing new applications on the hardware for users..
Check Stock

CAMWAY Oscilloscope Multimeter Intelligent Oscilloscope Automatic Waveform Multimeter 4000-Count Automatic Range Analog Bar Graph 200k High-Speed A/D Sampling 5 KHz ~ 500 KHz Frequency

  • 【 Multi- Function Industrial Home Tool】Fast Sampling Speed+ Auto Waveform Capture+Waveforms Data Display Hold+ Save / Read Up to 10 Waveforms & 100 Sets of Readings+Auto Shut-Off(after 15 minutes )+ LED Backlight & Screen+ 5 Colors Test Leads Alligator Leads+Complete Signal Input+ Data Processing+ Auto Search+ Waveform Storage Call+High Contrast+ High Resolution..
  • 【 Automatic Waveform Capture】 Display Hold , Save / Read Up to 10 Waveforms & 100 Sets of Readings, With Panel Calibration Technology, More Reliable, Since The Calibration Factor is Set inside, No Need to Adjust Potentiometers. Intelligent Oscilloscope Multimeter..
  • 【 Oscilloscope Test & Display】 DC voltage 1000V, AC voltage 750V, DC / AC Current 40A, Resistance 40MW, Capacity 10mF, Frequency 5Hz ~ 5MHz, Diode / Continuity Test. HFE and Remote Test , Accurate Display of DC-AD waveforms. Can Display The Waveforms of Signal Strength, Shape, Instantaneous Values..
  • 【 Fast Sampling Speed 】 A / D sample at 200 ksps with a Built-in 4000count Double A / D combination . Oscilloscope's Silent Mode And Waveform Transform Just by One-key During Measure..
  • 【 5 Colors Test Leads 】 Alligator leads Collocate With Oscilloscope Automatic Waveform Multimeter Can Quickly Solve Complex Problems in....
Check Stock

UNI-T Waveform Generators 120 MHz MAX. Output Frequency 320 MSa/s Sample Rate 16 bits Vertical Resolution 2 Channels 16 Mpts Arbitrary Wave Length (UTG2082B 80MHz 2CH)

  • Higher waveform capture rate Up to 200,000wfms/s waveform capture rate, greatly improving the capture pole The ability of low-probability events can more intuitively observe signal jitter and glitches, 256-level grayscale and color difference fluorescent display effect, waveform changes are visible..
  • Rich data measurement functions Support 34 kinds of automatic measurement parameter functions, Support Zoom, Math, statistics and advanced calculation functions..
  • Independent time base adjustable The time base of each channel is independently adjustable, and it has 4 windows display at the same time, which is convenient for users to observe four signals with large frequency differences.
  • Possess rich triggering and decoding functions, as well as waveform recording and playback functions Support bus decoding: I²C, SPI (only four channels), USB, CAN, optional: RS232/UART. Up to 100,000 frames waveform record,Record the waveform changes, replay the waveform conveniently, and analyze the fault.
  • UPO3254E 250MHz 4 2.5 GSa/s 70 Mpts 200000 wfms/s UPO3154E 150MHz 4 2.5 GSa/s 70 Mpts 200000 wfms/s.
Check Stock

ALMOCN for Digital Oscilloscope Kit Open-sourced 2.4″ TFT 1MSPS for Digital Oscilloscope DIY Kit Handheld Pocket Sized 13803K, SMD pre-soldered

  • Digital DIY Oscilloscope Kit uses ARM Cortex-M3 processor (STM32F103C8), 2.4-inch color TFT display screen can be used as ARM test development board. Can freeze at any time waveform display (HOLD function).Comes 1Hz /3.3V square wave test signal source..
  • Can be secondary development on the basis of this kit, for example, it can be changed to Millivoltmeter, data loggers.Adjustable vertical displacement, and with instructions..
  • With automatic, regular and one-shot modes, easy to capture the moment waveform.Available rising or falling edge trigger.Observable..
  • With waveform parameter digital display, including frequency, period, pulse width, duty ratio, MAX./MIN./AVG./Peak-Peak/virtual values.Waveform storage function: will not lose the waveform after power off..
  • The oscilloscope kit is a kit specially designed for professional teaching and training in electronics. Please note that this kit need to be assembled and soldered by yourself..
Check Stock

Megger MIT310-EN Insulation Tester, 1000 Megaohms Resistance, 250V, 500V, 1000V Test Voltage

  • Insulation tester for testing insulation resistance, voltage, and continuity in electrical installations.
  • Average-sensing meter provides accurate readings when measuring linear loads, where the current or voltage has a sinusoidal waveform.
  • Dual digital display with analog arc function to replicate response of analog meters.
  • Measures insulation resistance from 0 to 1,000 megohms, voltage from 0 to 600V, and continuity from 0.01 to 100 ohms.
  • Safety rated to European Standard EN61010-1 Category III, 600V and IP54 rated for protection against dust and splashing water.
Check Stock

Amprobe DGC-1000A Clamp Ground Resistance Tester

  • Ground resistance tester for measuring ground resistance, current, and continuity in multi-grounded systems.
  • True RMS meter provides accurate readings when measuring linear or non-linear loads where the current or voltage has a sinusoidal or nonsinusoidal waveform.
  • Clamp-on head to measure resistance on a ground rod without the use of additional ground rods and without disconnecting the grounds under test.
  • Measures ground resistance from 0.025 to 1,500 ohms and AC current up to 10A.
  • Safety rated to European Standard 61010-2-32 Category III 300V, Category II 600V.
  • Continuity beep if the resistance is lower than 40.00 Ohms.
Check Stock