Athena Parts Water Pump Gasket Kit with Bearings for KAWASAKI KX 250 F 2004-2008, SUZUKI RMZ 250 2004-2006, black
- Includes every gasket, O-ring, bearing, and seal required to rebuild a water pump..
- Typical kit includes the following -Bearings where applicable. -Rubber Seals. -Mechanical Water pump seal where applicable. -Side cover gasket. -Water pump gasket. -Snap rings located on water pump shaft. -Copper drain washers..
Check StockFLUENTPOWER 3/4 HP Utility Pump with Full Stainless Casing, Submersible Sump Water Pump with Float Switch,Max Lift 27 Ft and Max Flow 3300 GPH, 3/4" Garden Hose Adapter and 1"&1.5" MNPT Included
- 【Float Switch Automatically Control】- The pump is automatically ON/OFF controlled by float switch according to water level. It starts at water level 30~50cm and stop at 10~15cm. It can remove water down to 1 cm by manually control..
- 【Full Stainless Casing and Long Cable Cord】Solid metal casing is resistant to rust. This pump is only works with clean water that contains small solid less than 5mm. Pump also comes with a long 26.2ft cable cord, which allows pump to go deep enough (23ft) in the water..
- 【Oil-Filled Seal Structure with Thermal Protection】- Oil-filled seal structure gives pump longer duration, which is much longer than regular mechanical seal. Thermal protector ensures that the pump will not be burned out. Even when the pump trigger thermal overload protector, pump will rework after cooling down..
- 【3/4 HP Power High Efficiency】- Maximum capacity of transferring water up to 3300 GPH with 1.5″ discharge port and hose horizontally, Maximum delivery height is 28ft vertical, 2200 gallons per hour on at 10ft discharge lift..
- 【GHT 3/4″, NPT1″ and 1.5″ male tread connectors included】- With 1.5″ discharge port will give pump maximum output flow rate. Multiple hose adapters help you to get pump starte....
Check StockGo, Flush, Wash and Dry
- Internally mounted, high speed, non-clogging, centrifugal, waste macerating pump driven by powerful 240 watt, 12 volt dc, permanent magnet motor with ball bearings and robust ceramic seal, discharges up to 5ft (1.5m) above the base of the toilet..
- Raw Water Rinse pump inlet - ¾" (19mm) hose tails. Flush pump discharge - 1½" (38mm) hose tail..
- Jabsco, self-priming rinse pump up to 3m (10ft), dry running, diaphragm water pump driven by 12 volt dc, permanent magnet, ball bearing motor..
- One Touch 'Press and Release' switch pad mounted on wall with four flush and rinse finctions, sealed for life, with 10 -feet (3m) link cable, fitted quick connector, and heat shrink seal..
Check StockFLUENTPOWER 3/4HP Utility Pump 3300GPH Stainless Steel Submersible Sump Pump, Drain Clean Water for Basement Flood Cellar Pool Pond Garden and Hot Tub
- ☘【3/4 HP HIGH EFFICIENCY】Equipped with 3/4 HP powerful motor, the capacity of transferring water can be Max. 3300 GPH with 1.25" discharge hose horizontally. Pump has the ability to lift water up to Max. 28 ft vertical, 2200 gallons per hour on at 10 ft discharge lift. This utility pump works with CLEAN water which contains small solid less than 0.2"..
- ☘【FULL STAINLESS STEEL CASING】Assembled by integrated 304 stainless steel housing and pump base with better cooling ability for long life. Pump also comes with a 26.2 ft long cable cord, which allows pump to go deep enough (23 ft) in the water. This pump can be used in Min 7"x7" pit..
- ☘【SIMPLE PLUG-IN CONTROL】The pump ON/OFF is controlled by cable plug. It can start pumping water from 2" down to 0.4". Designed for quickly draining water in hot tub, water tank, rain barrel, swimming pool, garden ponds, wells and so on..
- ☘【SAFETY ENSURE& DURABLE】Oil-Filled Seal Structure gives pump longer duration, which is much longer than regular mechanical seal. Full corrosion-resistant shell and thermal protection ensures the pump will not be burned out, even when the pump trigger thermal overload protector, pump will rework after cooling down..
- ☘【EASY TO INSTALL】Comes with three plastic ada....
Check StockUtility Pump Replacement Carbon Brushes,Impeller,Shaft Seal Part for FPOWER Water Transfer pump (1 Set)
- Utility Pump Replacement Carbon Brushes,Impeller,Shaft Seal Part for FPOWER Water Transfer pump (1 Set).
- Package Content: 2 x Carbon Brushes, 1 x Impeller, 1 x Seal.
- Carbon Brush Size (Approx) : 18 x 6 x 6 mm.
- Impeller Measures: 1-3/8" Diameter, 1/2" Width with D Shaped Drive Hub for 5/16" Diameter Shaft.
- Impeller&Seal are also fits in FPOWER DC 12-Volt Utility Water Transfer Pump.
Check StockHand Bilge Pump Manual Hand Water Pump for Kayaks Canoes and Boats Emergency Hand-Operated Marine Bilge Pump with Reversible Hose
- ⛵HAND BILGE PUMP FOR BOATS: Our manual bilge pump length is 17", and the maximum unfolded length is 28.3", which is easy to store and takes up minimal space. It’s the perfect boating accessory for kayaks, canoes, dinghys and small boats. Our bilge pump remove water quickly and downward strokes for maximum efficiency and less fatigue.
- ⛵MAKES WATER REMOVAL EASIER & FASTER: Our hand water pump features a 34.6" long hose with a 1.16" intake nozzle and 1.37" diameter hose that makes reaching the bottom of your boat easier and removing excess water faster. This hand suction pump works great to remove water from the bottom of a motorboat, canoe or dinghy.
- ⛵EASY TO USE: Just simply connect the hose to the end of the pump, insert the bottom of the pump into the water, and use the handle to start pumping. It sucks water when you push the handle in, and disperses the water when you pull the handle out!.
- ⛵NO CLOG FILTER & ANTI-LEAK DESIGN GASKET: Our marine bilge pump Features a filtered nozzle to prevent seaweed, leaves and debris from clogging this hand water pump. And The premium rubber sea....
Check StockJabsco Lite Flush Compact 12 Volt Marine Electric Toilet with Panel Control
- Internally mounted, high speed, non-clogging, centrifugal, waste macerating pump driven by powerful 240 watt, 12 volt dc, permanent magnet motor with ball bearings and robust ceramic seal, discharges up to 5ft (1.5m) above the base of the toilet..
- Raw Water Rinse pump inlet - ¾" (19mm) hose tails. Flush pump discharge - 1½" (38mm) hose tail..
- Jabsco, self-priming rinse pump up to 3m (10ft), dry running, diaphragm water pump driven by 12 volt dc, permanent magnet, ball bearing motor..
- One Touch 'Press and Release' switch pad mounted on wall with four flush and rinse finctions, sealed for life, with 10 -feet (3m) link cable, fitted quick connector, and heat shrink seal..
Check StockLINGVUM Bilge Pump for Kayak Canoe and Boat - 17 Inch Manual Portable Kayak Hand Water Pumps with Reversible Hose Orange
- CONVENIENT BILGE MANUAL WATER PUMP --- Our manual bilge pump length is 16.5", the maximum unfolded length is 25.5", equipped with a 23.2"long hose. At the same time, Our bilge pump has two water inlets and a long hose that attaches to either end, removing water quickly and reducing your fatigue.
- MAKES WATER REMOVAL EASIER --- The maximum displacement is 0.4L each time. The premium rubber seal creates a watertight seal that won't come loose or leak allowing for the maximum amount of suction and discharge that performs better than other hand bilge pumps. Suction spacers can allow water to flow into the manual water pump at the fastest speed.
- SCENE TO BE USED --- Perfect for emergency water removal in boats, kayaks, canoes or dinghies. With our kayak bilge pump, rest easy knowing that you’ll have a quick and easy way of removing water in those difficult times. Spending time on the water is supposed to be fun! Perfect boating and kayaking accessory.
- LIGHTWEIGHT & PORTABLE --- This kayak hand pump is light (Only 0.78 pounds), easy to carry and store. Foam padded handgrip is non-slip and provides buoyanc....
Check Stock3\ DC 48V Deep Bore Well Solar Water Pump MPPT Controller Kits Submersible Solar Well Pumps Intelligent Deep Well Jet Pump Stainless Steel Deep Well Pump for Home,Lndustrial (600W)
- ✦【MPPT TECHNOLOGY】: The Solar Water Pump controller uses the latest MPPT technology to drive a high-efficiency brushless DC water pump motor to ensure that it can provide maximum flow under all light conditions..
- ✦【DOUBLE PROTECTION】: The Water Pump can protect the submersible pump from frequent start, overheating and dry operation under low light conditions..
- ✦【INTELLIGENT WATER SHORTAGE PROTECTION】: When there is no water in the well, the pump will automatically stop working and automatically start working after 15-30 minutes..
- ✦【ALLOY MECHANICAL SEAL】: The Solar Well Pumps adopts alloy mechanical seal, which has longer service life and higher reliability..
- ✦【APPLICATION】:The Solar Well Pumps are suitable for household and industrial purposes, providing convenience for life..
Check StockPump, Grinder, 2 HP, 15a
- Price For: Each Pump Body Material: Cast Iron Cord Length: 25 ft. Off Point: 8 GPM of Water @ 100 Ft. of Head: 9 Shaft Seal: Silicon Carbide/Double Viton Lip Motor RPM: 3450 Max Head – Pumps: 108 ft. Manufacturers Warranty Length: 3 Yr. GPM of Water @ 60 Ft. of Head: 42 HP: 2 GPM of Water @ 5 Ft. of Head: 50 Hz: 60 Input Phase AC: 1.
- GPM of Water @ 15 Ft. of Head: 50 Max. Liquid Temp.: 140 Degrees F Max. Head: 108.0 ft. Voltage: 208/230 Amps: 15 GPM of Water @ 10 Ft. of Head: 50 Item – Grinder Pumps: Grinder Pump Item: Grinder Pump GPM of Water @ 80 Ft. of Head: 27 Base Material: Cast Iron Bearing Type: Upper and Lower Ball GPM of Water @ 35 Ft. of Head: 50 Pump RPM: 3450 GPM of Water @ 40 Ft. of Head: 48.
- GPM of Water @ 30 Ft. of Head: 50 Switch Type: Tether Impeller Material: Stainless Steel On Point: 15 Handle: Yes Housing Material: Cast iron Max. Head – Pumps: 108 ft. GPM of Water @ 45 Ft. of Head: 48 GPM of Water @ 70 Ft. of Head: 35 Min. Sump Pit Dia.: 24″ GPM of Water @ 50 Ft. of Head: 46 GPM of Water @ 25 Ft. of Head: 50 Switch Type – Pumps: Tether Impeller Material – Pumps: Stainless Steel.
- Cord Length – Pumps: 25 ft. Pump HP: 2 Height: 19-1/2″ Phase: 1 Motor Type: PSC Length: 12-1/2″ FNPT GPM of Water @ 55 Ft. of Head: 45 GPM....
Check StockAmarine Made DC 12V Farm & Ranch Solar Water Pump Submersible Well booster Pump 26ft Lift (Orange)
- Model:ZQB-12,Size:10.83 x 7.1 x 7.1 inches,Voltage:DC 12V,Power:125W,Outlet Dia: 1"(25mm),Max Head:8m(26ft) ,Capacity:100L/min.
- DC water pump is made of motor and pump,the motor is consists of rotor,bearing and base.
- the pump body includes impeller,pump body,connections,bearing and mechanical seal..
- This series pumps adopt stainless steel DC elect-motor,equipped with perfect electric protective device and waterproof seal..
- 12V DC Submersible water pump is applicable to the same voltage power of ship or irrigation etc,it is very convenient..
- Simple structure, less components, easy maintenance and repair.Stable Performance.
- has less power cost, larger flow and great anti-corrosion ability..
Check StockDontmiss Automatic Submersible Small Boat Bilge Pump 12v 1100gph Auto with Float Switch bilge pump for boat(Outlet Diameter:1 1/8\) (1100GPH)
- LONG HOSE FOR EASY WATER REMOVAL: A 39" long hose lets you reach deep areas to discharge with ease. 1" intake nozzle, 14" chamber and 1.25" diameter hose to remove water quickly. 115 cubic inches per pump or 1 gallon removal in 2 to 3 pumps..
- NO CLOG FILTER & WATERTIGHT GASKET: A rubber seal creates a watertight seal that won't leak allowing for maximum suction with the manual water pump. Features a filtered nozzle to prevent seaweed, leaves and debris from clogging the hand siphon pump..
- LIGHTWEIGHT, PORTABLE & IDEAL FOR EMERGENCIES: The hand pump is light and easy tostore, making it perfect for emergency use in small boats, kayaks, canoes or dinghy. Does not require power making it ideal as an emergency bailer or in kayaking..
- EXCEPTIONAL QUALITY: Our marine-grade bilge pump is specially designed to quickly remove water from hard to reach places season after season. We use premium materials not found in other lesser quality boat, RV, car and home products..
- WHY BETTER BOAT: We are a family owned American business committed to making premium quality interior & exterior RV care and boat cleaning supplies. We stand behind your satisfaction and our hand water pump or hand held bilge pumps for boats..
Check StockJEREPET 2000GPH Pond pump,Submersible Water Pump,high lift waterfall pump,with barrier bag, used as fountain pump outdoor,for Koi Pond Statuary Aquarium 18FT Max Lift 115W
- Professional pond pump:This 2000 gallon per hour 115W submersible water pump comes with high-efficiency epoxy protected asynchronous motor,oil-free and magnetic-driven ,with 16feet certified cable with US type 3pin plug, 18feet max lift height..
- Durable seal impeller and shafts: With wear-resistant anti-corrosion ceramic shaft, silicon carbide bearings,longer life and more efficient ,use seal impeller ,high lift and quiet operation (less than 40db)and energy saving.
- Simple Installtion &Maintenance:With detachable intake screen and pump cover,3 position adjustable outlet direction,with flexible tube size clear outlet adapter,4 suction rubber feet and portable handle..
- Multiple application: This water pump are ideal used as pond pumps ,founatin pump,waterfall pump ,filter system pump,outdoor ponds submersible fountain pump,KOI circulation/return pump ,hydroponic pump, statuary pump,can be used as a submersible or inline pump.
- 17.7"Large Pond Pump Barrier Bag Included:Comes with 17.7"x 17.7" mesh bag , help to prevent debris such as leaves from blocking the pump when used as pond pumps submersible outdoor..
Check Stock