Reviews Titanium Nitride Coated End Mill

Niagara Cutter C430R-0.375-D3-R030.0-Z4 C430R Carbide Radius End Mill TiAlN Finish 4 Flutes 3/8 Cutting Diameter 3/8 Shank Diameter 2-1/2 Overall Length 1

  • Corner radius end mills have cutting edges with rounded corners to reduce chipping and provide longer tool life.
  • Four flutes produce a better finish than fewer flutes.
  • Carbide can run at higher speeds than high-speed steel, resisting abrasion and high cutting temperatures.
  • Titanium aluminum nitride (TiAlN) coating lubricates the end mill for high-temperature stability and abrasion resistance at high cutting speeds.
  • Center-cutting design allows the end mill to plunge into material like a drill bit while also performing conventional surface milling.
Check Stock

IRWIN Drill Bit Set, Titanium Nitride Coated, 29-Piece (3018003)

  • Titanium Nitride Coated-coated nitride drill bits last longer and feature a cutting edge that stays sharp.
  • 135° split-point tip starts drilling immediately and helps eliminate walking.
  • IRWIN drill bits are great for repetitive metal drilling with portable drills and for use in stationary drill presses.
  • Includes 1/16" through 1/2" drill bit sizes in 1/64" increments.
  • Titanium Nitride drill bits last longer and feature a cutting edge that stays sharp.
Check Stock

YG-1 EH970 Carbide Square Nose End Mill, Long Reach, TIALN Multilayer Finish, Roughing Cut, 45 Deg Helix, 4 Flutes, 2.5\ Overall Length, 0.25\ Cutting Diameter, 0.25\ Shank Diameter

  • Roughing end mills have chip-breaking cutting edges that remove material in less time than conventional end mills.
  • Fine-pitch tooth design and tool geometry are suitable for machining steel up to Rockwell hardness C45, stainless steel, titanium alloys, and nickel-based alloys.
  • Long-reach end mills have an extended shank for access to recessed areas of the workpiece.
  • Titanium aluminum nitride (TiAlN) coating lubricates the end mill for high-temperature stability and abrasion resistance at high cutting speeds, offering better heat resistance than TiN and TiCN coatings.
  • Carbide can run at higher speeds than high-speed or cobalt steel, resisting wear and high cutting temperatures.
Check Stock

5PCS R0.5-3mm Ball Nose Carbide End Mill Set CNC Cutter Router Bits 2 Flute Spiral Milling Tool End Mill Set Includes 5 Radius Sizes Of 0.5mm 1mm 1.5mm 2mm 3mm

  • Applicable Materials: ball mill bit usually used for steel（Carbon steel/Alloy steel/Hardened steel/Cast lron, etc.）.
  • Ball End Mill Specification -- Cutting Diameter: 1 - 6MM（1mm 2mm 3mm 4mm 6mm），Shank Diameter:4 - 6MM（4mm 4mm 4mm 4mm 6mm），Cutting Length:2 - 12MM（2mm 4mm 6mm 8mm 12mm），Overall Length:50MM.
  • Wide Compatibility: ball nose end mill set are compatible with most desktop CNC machines, as well as other industrial CNC machines. Just make sure you select the correct-sized collet for your device..
  • High Quality:made from solid tungsten carbide (TC)，have a Titanium Nitride (TiN) surface to improve heat resistance and reduce wear..
  • Used it strictly for steel, it worked great for that, eats metal fast ，beautiful surface finish!Watch your stick out and travel speeds..
Check Stock

YG-1 E5021 Carbide Square Nose End Mill, TIALN Multilayer Finish, 30 Deg Helix, 4 Flutes, 2.5\ Overall Length, 0.25\ Cutting Diameter, 0.25\ Shank Diameter

  • Suitable for general-purpose machining on steel, chromium-nickel steel, and cast iron.
  • Four flutes produce a better finish than fewer flutes.
  • Titanium aluminum nitride (TiAlN) coating lubricates the end mill for high-temperature stability and abrasion resistance at high cutting speeds, offering better heat resistance than uncoated finish, TiN coating, and TiCN coating.
  • Carbide can run at higher speeds than high-speed or cobalt steel, resisting wear and high cutting temperatures.
  • Square nose end mills (also called square end) create sharp, unrounded cuts.
Check Stock

SPEED TIGER ICSM Chamfer End Mill- CNC Carving Bits V Groove 90 Degree 3/8 Diameter 3 OVL for Wood/Alloy Steels/Hardened Steels-Made in Taiwan 1 Piece 3/8 90°

  • GENERAL APPLICATION CUTTER - Speed Tiger carbide tools excel at working wood, aluminum, copper, MDF, carbon steels (~HB225), alloy steels (HB225~325), pre-hardened steels (up to HRC45), hardened Steels (HRC40~45), cast iron.
  • Ideal for Chamfering, Carving V Groove, Centering.
  • 90 Degree, Shank Diameter: 3/8", Full Length: 3”.
  • HIGH PERFORMANCE FOR HARD MATERIALS - Cutter is made of Micro Grain Carbide that is very tough, resists wear and offers high cutting performance.
  • ZrN-A COATING - Zirconium nitride (ZrN) +Titanium aluminum boron nitride (AlTiBN) coating lubricates the end mill for stability at high temperature and superior wear resistance at high cutting speeds, offering better heat resistance than TiAlN, TiN or TiCN coatings.
Check Stock

SpeTool 5PCS Ball Nose End Mill Cutter CNC Router Bits Double Flute HRC55 Spiral Milling Tool 1/4 Inch Shank 2-1/2 Inch Length OVL

  • 5PCS Solid Carbide Ball Nose Router Bit with 1/4 inch Shank and 1/8 inch Cutting Radius, 3/4 inch Cutting Length, 2-1/2 inch for Total Length.
  • The End Mill Round Top with 2-Flute, Material: HRC55 Carbide with TiAlN Coated.
  • For CNC,Engraving Machine.Carbon Steel, Mould Steel, Inconel, Stainless Steel, Titanium Alloy etc.
  • The Ball Nose End Mill Suit for CNC Machine, Router and Makita, Bosch, and Any Brand Plunge Router with 1/4" Collet.
  • End Mill Bits are Suitable for Side Milling, End Milling, Finish Machining, etc..
Check Stock

YG-1 E5023 Carbide Square Nose End Mill, Double End, TIALN Multilayer Finish, 30 Deg Helix, 4 Flutes, 2\ Overall Length, 0.140625\ Cutting Diameter, 0.1875\ Shank Diameter

  • Double-end square end mills create sharp, unrounded cuts and have cutting edges on both ends for longer tool life.
  • Suitable for general-purpose machining on steel, chromium-nickel steel, and malleable cast iron.
  • Stub length increases the strength of the tool, making it less likely to break in the workpiece.
  • Four flutes produce a better finish than fewer flutes.
  • Titanium aluminum nitride (TiAlN) coating lubricates the end mill for high-temperature stability and abrasion resistance at high cutting speeds, offering better heat resistance than uncoated finish, TiN coating, and TiCN coating.
Check Stock

Riedell UPTOWN 120 BR Mens Rhythm Skates 2009 - Size 5

  • TOP QUALITY CRAFTSMANSHIP - These precision bearings come equipped with hardened Swiss chromium steel alloy balls that can endure long-lasting use..
  • OPTIMIZED DURABILITY - The KwiK Swiss Nitride bearings use a Titanium Nitride coating. This coating does not chip, flake, or degrade during prolonged rough use..
  • CORROSION RESISTANT DESIGN - The KwiK bearings' Titanium Nitride-coated races resist corrosion. They also provide strength and smoothness to create a performance with the greatest roll..
  • FRICTION RESISTANT RETAINERS - These bearings come equipped with friction resistant Delrin retainers that are pre-spun with high-performance oil..
  • SLEEK & LUXURIOUS DESIGN - The 8mm skate bearings come with a metallic gold finish, a design that is worthy of its performance. This product is not a children's product and is not designed or intended for use by children 12 years of age or younger..
Check Stock

Niagara Cutter - C430-0.188-D7-S.0-Z4 N85729 Carbide Square Nose End Mill, Inch, TiAlN Finish, Roughing and Finishing Cut, 30 Degree Helix, 4 Flutes, 3\ Overall Length, 0.188\ Cutting Diameter, 0.188\ Shank Diameter

  • 4 flute design for creating finer finishes and a highter metal removal rate General purpose end mill for working all types of materials Made of extra-fine grade carbide for ultra high transverse rupture strength Titanium Aluminum Nitride (TiAlN) combines high thermal stability with excellent hardness for abrasion resistance and a low coefficient of friction, for lubricity Center Cutting End Mills are designed with "End Teeth" making these ideal for Slotting and Cavity applications.
Check Stock

SpeTool 5PCS 12401 4 Flutes Carbide CNC End Mill, Square Nose 1/4 inch Shank, 2-1/2 inch Long Overall, Titian Coated for Metal Mill

  • Solid Carbide Spiral Router Bit with 1/4 inch Shank and 1/4 inch Cutting Diameter, 3/4 inch Cutting Length, 2-1/2 inch for Total Length.
  • The End Mill With Flat Top, 4-Flute, For Finishing, Material: HRC55 Carbide with TiAlN Coated.
  • For CNC,Engraving Machine.Carbon Steel, Mould Steel, Inconel, Stainless Steel, Titanium Alloy etc.
  • The Route Bit Suit for CNC Router and Makita, Bosch, and Any Brand Plunge Router with 1/4" Collet.
  • End Mill Bits are Suitable for Side Milling, End Milling, Finish Machining, etc..
Check Stock

SpeTool 12411 4 Flutes Carbide CNC Square Nose End Mill, 1/4 inch Shank Diameter, 3 inch Long, Upcut CNC Router Bit with Coated

  • Solid Carbide Spiral Router Bit with 1/4 inch Shank and 1/4 inch Cutting Diameter, 1-1/8 inch Cutting Length, 3 inch for Total Length.
  • The Square CNC End Mill With Flat Top 4-Flute, Carbide with TiAlN Coated Gives outstanding cutting performance and wear resistance.
  • For CNC, Excellent performance to cut Carbon Steel, Mould Steel, Inconel, Stainless Steel, Titanium Alloy etc, Up to HRC 55..
  • The Route Bit Suit for CNC, Router and Makita, Bosch, and Any Brand Plunge Router with 1/4" Collet.
  • End Mill Bits are Suitable for Side Milling, End Milling, Finish Machining, etc. For better.
Check Stock

SpeTool CNC Router Bits Carving 8 Pcs Set for Wood Detail Profile V Groove Engraving Solid Carbide 1/4 Inch Shank

  • The Carving bits kits of Tapered Ball Nose, Spiral, Cone End Mill Cutter.
  • For CNC,Engraving machine.Carving Wood, plywood, MDF, plastics, acrylic, stainless steel, titanium alloy etc.
  • Long service life, Decreasing the times of changing cutters,Saving production time.
  • Include 3*carbide end mills ( 2 pc v-groove end mill, 1pcs tapered end mill ), 4*Spiral End Mill (3 pc up cut, 1 pc down cut), 1*ball end mill.
  • The Carbide End Mill Suit for CNC Router and Makita, Bosch, and Any Brand Plunge Router with 1/4" Collet.
Check Stock