Reviews Three Phase Diode

AOICRIE 4PCS L298N Motor Drive Controller Board Module Dual H Bridge DC Stepper for Arduino

  • L298N as Main driver chip L298N, strong driving ability, strong anti-interference, low calorific value, afterflow diode protection, more stable and reliable for Arduino projects, Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability..
  • Double H bridge design, can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors, high efficient, To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage..
  • Driving DC motor Because the module is drived by double H bridge,it can drive two motors simultaneously.Input the following driving timing from IN1-IN4 then the speed and direction of the stepper motor can be controlled..
  • Easy to Use No assembly required. This L298N board comes ready to go. Just wire up motors and power, easy to use..
  • Wide Usage Great for DIY Smart Car Robot Power MEGA R3 for Mega2560 Duemilanove, if driving voltage is more than 12V, use external standard 5volt TTL outputs to switch the H-bridge circuits..
Check Stock

Garosa Voltage Monitoring Relay, Overvoltage Undervoltage Monitoring Sequence Protector with LED Lights, 480VAC

  • 【Item Main Purpose】This phase sequence protector is mainly used for various fault detection of 3-phase voltage.not easy to be damaged, can be used for a long time without worry..
  • 【5 Indicators To Indicate】Normal, phase loss (voltage three-phase unbalance), reverse phase, overvoltage and undervoltage.We fully guarantee the quality of our products.Please rest assured to buy our items..
  • 【Full-Featured】It integrates three-phase voltage display, over-voltage protection, under-voltage protection, phase-gap protection (phase-break protection), three-phase voltage unbalance protection, phase sequence protection (phase-staggered protection) and acoustooptic alarm..
  • 【Installation Method】The base of the protector adopts a rail type with two screw holes, which can be directly installed separately or mounted on the HT35 rail..
  • 【Application Scenarios】This phase sequence protector is widely used in air compressor, motor distribution box, pump, central air conditioning units, power distribution cabinet, crane, etc.Safety using. If you still have any questions, please send us emails, we're available 24 hours..
Check Stock

Siemens 3UG4631-1AW30 Monitoring Relay, Single Phase Voltage Monitoring, Screw Terminal, 1 CO Contacts, 0.1-60VAC/DC Measuring Range, 0.1-30V Hysteresis, 0-20s Delay Time, 24-240VAC/DC Auxiliary Voltage

  • 3 INDICATORS-The protector base adopts 35mm rail type or device type, and has two screw hole structures inside, which can be directly installed separately or HT35 rail. Indicated by three indicators: normal, phase loss(voltage three-phase unbalance), reverse phase.
  • PHASE LOSS PROTECTION-Phase loss protection means that when the protected line is in the running state or non-operating state, any phase failure occurs, and the delay is 2S.
  • REVERSE PHASE PROTECTION-Reverse phase protection, a protection measure to prevent L1, L2, L3 three-phase AC phase sequence from being connected incorrectly, delay 2S action.
  • VOLTAGE IMBALANCE PROTECTION-Voltage imbalance protection, which refers to a protective measure that will affect the safe operation of the line due to three-phase voltage imbalance.
  • IDEAL FOR-Widely used in air compressors, electric motors, distribution boxes, water pumps, oil pumps, central air conditioning units, etc.
Check Stock

MC14046BCP Phase Lock Loop (PLL) IC 1.9MHz 1 16-DIP (0.300\

  • The CD4046B CMOS Micropower Phase-Locked Loop (PLL) consists of a low-power, linear voltage-controlled oscillator (VCO) and two different phase comparators having a common signal-input amplifier and a common comparator input..
  • Very low power consumption: 70 µW (typ.) at VCO, VCO inhibit control for ON-OFF keying and ultra-low standby power consumption fo = 10 kHz, VDD = 5 V, Source-follower output of VCO control input (Demod. output), 100% tested for quiescent current at 20 V.
  • Operating frequency range up to 1.4 MHz (typ.) at VDD = 10 V, RI = 5 k, High VCO linearity: 003c1% (typ.) at VDD = 10 V, 5-V, 10-V, and 15-V parametric ratings.
  • Low frequency drift: 0.04%/°C (typ.) at VDD = 10 V, Choice of two phase comparators: Exclusive-OR network (I) Edge-controlled memory network with phase-pulse output for lock indication (II), Zener diode to assist supply regulation, Standardized, symmetrical output characteristics, Meets all requirements of JEDEC Tentative Standard No. 13B, "Standard Specifications for Description of 'B' Series CMOS Devices".
  • A Versatile Building Block for Micropower Digital and Analog Applications, Example Applications: FM demodulator and modulator, Frequency synthesis and multiplication, Frequency discriminator, Data synchronization....
Check Stock

1pcs/lot Brand CD4HC7046AE 74HC7046 DIP-16 Phase-Locked Loop

  • The CD4046B CMOS Micropower Phase-Locked Loop (PLL) consists of a low-power, linear voltage-controlled oscillator (VCO) and two different phase comparators having a common signal-input amplifier and a common comparator input..
  • Very low power consumption: 70 µW (typ.) at VCO, VCO inhibit control for ON-OFF keying and ultra-low standby power consumption fo = 10 kHz, VDD = 5 V, Source-follower output of VCO control input (Demod. output), 100% tested for quiescent current at 20 V.
  • Operating frequency range up to 1.4 MHz (typ.) at VDD = 10 V, RI = 5 k, High VCO linearity: 003c1% (typ.) at VDD = 10 V, 5-V, 10-V, and 15-V parametric ratings.
  • Low frequency drift: 0.04%/°C (typ.) at VDD = 10 V, Choice of two phase comparators: Exclusive-OR network (I) Edge-controlled memory network with phase-pulse output for lock indication (II), Zener diode to assist supply regulation, Standardized, symmetrical output characteristics, Meets all requirements of JEDEC Tentative Standard No. 13B, "Standard Specifications for Description of 'B' Series CMOS Devices".
  • A Versatile Building Block for Micropower Digital and Analog Applications, Example Applications: FM demodulator and modulator, Frequency synthesis and multiplication, Frequency discriminator, Data synchronization....
Check Stock

Digital Phase Indicator , Akozon SP8030 Digital Phase Rotation Indicator LED Buzzer Phase Sequence Meter 200 ith Bag

  • It is durable, reliable and light-weight handheld device, which is necessary tool for those who often install, repair or maintain three-phase system or motor..
  • Without a need to link testing line, the motor rotation direction can be decided by placing this indicator above the motor and aligning it with motor drive shaft..
  • Used to test phase sequence input of three-phase voltage, to indicate phase line L1, L2 and L3..
  • PM5900 Motor and Phase Rotation Indicator is used to test magnetic field direction of three-phase system, phase rotation, motor rotation direction..
  • It also supports non-contact type magnetic field rotation direction test (motor rotation direction test)..
Check Stock

Phase Sequence Meter, 60V ~ 600V AC 3 Phase Sequence Rotation Tester, with 5 LED Lights, for General Measuring Tool

  • It is durable, reliable and light-weight handheld device, which is necessary tool for those who often install, repair or maintain three-phase system or motor..
  • Used to test phase sequence input of three-phase voltage, to indicate phase line L1, L2 and L3..
  • PM5900 Motor and Phase Rotation Indicator is used to test magnetic field direction of three-phase system, phase rotation, motor rotation direction..
  • Without a need to link testing line, the motor rotation direction can be decided by placing this indicator above the motor and aligning it with motor drive shaft..
  • It also supports non-contact type magnetic field rotation direction test (motor rotation direction test)..
Check Stock

Omron K8DS-PH1 Phase Monitoring Relay

  • The base of the protector adopts a rail type with two screw holes, which can be directly installed separately or mounted on the HT35 rail..
  • Use 5 indicators to indicate: normal, phase loss (voltage three-phase unbalance), reverse phase, overvoltage and undervoltage..
  • Phase loss protection means that when the protected line is in the running state or non-operating state, any phase failure occurs, and the delay is 2S..
  • Overvoltage protection means that the voltage of the protected line is higher than the set value, and the delay is 3~8S, and the recovery is 6~20VAC..
  • Reverse phase protection, a protection measure to prevent L1, L2, L3 three-phase AC phase sequence from being connected incorrectly, delay 2S action..
Check Stock

1Pcs Photocell Cap,TwistLock Photocell Shorting Cap,Photo Control Sensor Receptacle with Surge Protection,Dusk to Dawn 3 Prong Bypass Cap

  • ◆ Function: phase sequence detection, live line check, simple performance check, live cable identification, phase loss assessment, search for cable break position, detection of DC line break point, line maintenance.
  • ◆ Non-Contact Inspection: Non-contact inductive measurement of the terminal type without opening the cable, without touching the exposed high voltage fire cable, with the three highly insulated super inductive terminals inserted directly into the cable insulation skin 3-phase live detection for safe and quick productivity..
  • ◆ Positive and Negative Phase: With the LED display, dynamic sound and light perfectly show the positive or negative phase of the phase sequence of the three-phase power supply, which can be seen at a glance..
  • ◆ Magnetic base: The base plate of the instrument is equipped with 4 magnets that can stand a quality of 800 g. They can be attached to the metal case of the device during the test, and it is convenient and convenient to use..
  • ◆ Wide Voltage Test: This phase meter can detect three-phase voltages from 70V to 1000V and has excellent performance..
Check Stock

Juried Engineering CD4046BE CD4046B CD4046 CMOS Micropower Phase-Locked Loop Breadboard-Friendly IC DIP-16 (Pack of 5)

  • The CD4046B CMOS Micropower Phase-Locked Loop (PLL) consists of a low-power, linear voltage-controlled oscillator (VCO) and two different phase comparators having a common signal-input amplifier and a common comparator input..
  • Very low power consumption: 70 µW (typ.) at VCO, VCO inhibit control for ON-OFF keying and ultra-low standby power consumption fo = 10 kHz, VDD = 5 V, Source-follower output of VCO control input (Demod. output), 100% tested for quiescent current at 20 V.
  • Operating frequency range up to 1.4 MHz (typ.) at VDD = 10 V, RI = 5 k, High VCO linearity: 003c1% (typ.) at VDD = 10 V, 5-V, 10-V, and 15-V parametric ratings.
  • Low frequency drift: 0.04%/°C (typ.) at VDD = 10 V, Choice of two phase comparators: Exclusive-OR network (I) Edge-controlled memory network with phase-pulse output for lock indication (II), Zener diode to assist supply regulation, Standardized, symmetrical output characteristics, Meets all requirements of JEDEC Tentative Standard No. 13B, "Standard Specifications for Description of 'B' Series CMOS Devices".
  • A Versatile Building Block for Micropower Digital and Analog Applications, Example Applications: FM demodulator and modulator, Frequency synthesis and multiplication, Frequency discriminator, Data synchronization....
Check Stock

Juried Engineering CD4046BE CD4046B CD4046 CMOS Micropower Phase-Locked Loop Breadboard-Friendly IC DIP-16 (Pack of 10)

  • The CD4046B CMOS Micropower Phase-Locked Loop (PLL) consists of a low-power, linear voltage-controlled oscillator (VCO) and two different phase comparators having a common signal-input amplifier and a common comparator input..
  • Very low power consumption: 70 µW (typ.) at VCO, VCO inhibit control for ON-OFF keying and ultra-low standby power consumption fo = 10 kHz, VDD = 5 V, Source-follower output of VCO control input (Demod. output), 100% tested for quiescent current at 20 V.
  • Operating frequency range up to 1.4 MHz (typ.) at VDD = 10 V, RI = 5 k, High VCO linearity: 003c1% (typ.) at VDD = 10 V, 5-V, 10-V, and 15-V parametric ratings.
  • Low frequency drift: 0.04%/°C (typ.) at VDD = 10 V, Choice of two phase comparators: Exclusive-OR network (I) Edge-controlled memory network with phase-pulse output for lock indication (II), Zener diode to assist supply regulation, Standardized, symmetrical output characteristics, Meets all requirements of JEDEC Tentative Standard No. 13B, "Standard Specifications for Description of 'B' Series CMOS Devices".
  • A Versatile Building Block for Micropower Digital and Analog Applications, Example Applications: FM demodulator and modulator, Frequency synthesis and multiplication, Frequency discriminator, Data synchronization....
Check Stock

1-600MHz RF Power Meter，Jectse Digital LCD RF Power Meter -75~16 dBm 1-600MHz Radio Frequency Attenuation Value

  • Repetitive Peak Reverse Voltage(AC):1200V.
  • 【Material】 - The rectifier diode is made of aluminum, with large current capacity, good heat dissipation, and low voltage.
  • 【Features】 - The two-pole rectifier has low power loss, low reverse leakage current, electrically isolated metal shell, which can maximize heat dissipation.
  • 【Advantage】 - This is a high-quality two-pole rectifier used to convert AC input to DC output, which can be used in a variety of applications.
  • 【Application】 - This rectifier is used in the rectification circuit of electrochemistry, electrolysis, electrolysis, traction, switchgear operation power supply, etc.
Check Stock

KAIWEETS Multimeter, Electric Tester, Pen-Type Multimeter, Digital Multimeter 0.8-600V,Professional Multimeter Pen for AC/DC Voltage/Live Wire Test/Capacitance/Resistance/Continuity/Diode,ST120

  • 【Multi-Parameter Measurement】Enter the Smart (Auto) mode by default, the digital multimeter automatically identifies and measures AC/DC Voltage, Resistance, and Continuity. It also tests Capacitance, Diode, Frequency, and Live Wire..
  • 【Phase Sequence 】ST120 stands out with its unique phase sequence detection. When turn on the “PA” mode, the operator can detect whether the phase sequence is clockwise or anti-clockwise..
  • 【Easy to Use】Switch measurement mode with button “Func” and hold data with button “H” . Backlight LCD screen ensures reading to be clearly seen in either dark or bright areas. The flashlight below the red probe helps you to work without concerns under dim light..
  • 【Wide Application】 Industrial electrical safety measurements, household electric problems, vehicle and circuit inspection..
  • 【 Customer Service】Lifelong technical support is guaranteed. Please don’t hesitate to contact us if there are any questions with our ST120 pen-type multimeter..
Check Stock