5pcs M8 x 1.25 x 35mm Stainless steel Long Coupling Hex Nut Connector
- 1/4-28 X 7/8" long, fine threads, 3/8" across the flats steel coupling nut with zinc finish.
- Coupling nuts are threaded fasteners for joining two male threads, most commonly threaded rod.
- Zinc plate over steel - more rust resistant.
- Coupling Nuts are used to make up long rod assemblies from shorter lengths of rods.
Check Stock
6 Pieces 8/32 Inch M4 12 Inch Threaded Rod with Hex Nuts Set Includes 6 Pcs M4 x 300 mm 304 Stainless Steel Fully Threads Studs Rods and 6 Pcs Thread Hex Nuts for Beaded Garden Stake Rods
- What You Will Get: the package comes with 6 pieces of 8/32 inch M4 12 inch threaded rods and 6 pieces of M4 hex nuts, 12 pieces or 6 set in total, nice combinations for you to make 6 pieces of fairy garden stakes, as well as other DIY crafts.
- Detailed Size: threaded studs: thread diameter is M4, and measures approx. 300 mm/ 12 inch in fully length.
- Hex nut: the coarse thread diameter is M4, pitch: 0.7 mm/ 0.03 inches, flat across width: 7 mm/ 0.28 inch and about 2.8 mm/ 0.11 inch high.
- Threaded Rods Studs: the threaded steel rod is made of quality 304 stainless steel material, sturdy, and resistant to rust or corrosion, with strong construction, hard to deform or break, which can be applied for a long time, and ideal accessories for assembly fastening, just screw into the threaded nut or threaded hole.
- Hex Nut: the hex nut can be screwed to this threaded rod well, not easy to slip off, besides, it is also an ideal accessory for fasteners, it is also essential in daily life, just need to screw it to the thread metal rods, bolts and other tools of the same size are fine.
Check Stock
CCC, French Press 5 Part Stainless Steel 3.75 Inch Wide Plunger Assembly For Flat Top 34 oz 8-Cup 1 Liter Coffee Press Replacement Part
- ...r Chef, Utopia Kitchen & other flat lidded "8-Espresso Cup" 32|34oz French Press coffee makers.
- Not OEM Bodum, Compatibly Manufactured by CCC for flat lidded 1 Liter French Press Coffee Makers.
- [DIRECTIONS FOR USE] Take apart your old plunger & thread the rod into the hole on you flat lid.
- Carefully start the finely threaded nut with rounded opening on top – if it gets “cross threaded” it will get stripped.
- spiral plate first, mesh filter sandwiched with cross plate below & thread the stem of the cross plate over the rods end, screw the closed nut snugly down (it will rest on your spiral plate)..
- [GOOD QUALITY MATERIALS] 304 GRADE Stainless Steel (SS) PLUNGER ROD with closed nut, cross plate with threaded stem, spiral plate, one 18/8 SS wire mesh filter with a SS plunging knob.
- Try CCC's 34oz Replacement Glass - it's FIRE TOUGHENED with measures.
- Also Filter Parts, Cross, Filter and Spiral plate assemblies.
- and Pour Over options to use on your press carafe coming soon..
Check Stock
Savior For Sale: Da Vinci's Lost Masterpiece?
- ...a total 3 easy steps: 1. Push it! 2. Lock it! 3. Rock it!.
- 【Durable & Strong】-- These cymbal nuts won't fly off when you are drumming, they won't turn loose when you are drumming on stage. With push-buttons of fully engaged, they will firmly grip onto the threaded rod of your cymbal stand so that they could withstand hard hitting on heavy-weight cymbals..
- 【Perfect for Drummer】-- These cymbal nuts are the great replacement parts for drum set kit, which are perfect for drummer music performance, they help to avoid rattle & contact noise while recording drums!.
- 【Easy Set-up & Tear-down】-- When you squeeze the push-buttons, the spring system swiftly disengages its grip on the threaded rod of your cymbal stand, so you can remove your cymbal nut in a flick! When you release the push-buttons, the spring system firmly engages its grip on the threaded rod of your cymbal stand. But you'll still be able to remove your cymbal & cymbal nut effortlessly within 2 seconds!.
- 【Pack & Size】-- Include 6PCS cymbal nuts. Size dimensions for each one: Th....
Check Stock
26 Pack 8/32 Inch Threaded Rods with Hex Nuts M4 12 Inch 304 Stainless Steel Fully Rod Threaded, 13 Pcs M4 300mm Right Hand Threads, 13 Pcs Hex Nuts for Hangers, U-Bolts and Beaded Garden Stake Rods
- 【THREADED RODS PARAMETERS】Thread Diameter M4: 2.8mm/0.11 ''.
- 【MATERIAL】304 stainless steel material, corrosion resistance, high temperature resistance, rust resistance and good processing performance.
- 【FULL THREAD & HEX NUT】For assembly and fastening, threaded rod is a fastener reinforced in threaded nut or threaded hole, right-hand threaded rod stud. Hexagonal nuts are an ideal replacement for industrial and construction fasteners, Simply screw on to a bolt of the same thread size, quick and easy..
- 【APPLICABLE SCENARIOS】Perfect for auto parts, standoffs, bolts and more metal items that need to be fastened.
- 13 Pcs full threaded rods, 13 Pcs full threaded hex nuts, 26 Pcs in total, perfect for garden stakes decorative beaded garden stakes etc for outdoor decoration..
- 【PACKAGE LIST】13Pcs M4×300mm threaded rods, 13 Pcs M4 Stainless Steel Fully Threaded Hex Nuts, which can be cut, heated, drilled and used in multiple dimensions..
Check StockScrew Post Fit for 5/16 inch 8mm Hole Dia Fully Threaded Rod M6x40mm Nut 15mm Hex Drive Binding Bolts for Leather Wood Furniture Carbon Steel Galvanized 4 Sets
- Size - Applicable Hole Dia: 5/16 inch(8mm).
- Nut Head Diameter: 13mm, Thread Pitch: 1mm..
- Materials - Made of carbon steel material, galvanized, the screws are strong and durable for use..
- Easily use: Easily applied with standard tool. Threaded post lets you open and re-attach piece where needed..
- Notice - The thickness of the object which is locked, at least 3mm less than the length of the screw rod + nut rod, otherwise, it will not be able to tighten..
- Application - Widely used in DIY projects, clothing making, leather crafts and furniture installation. Can be use for leather belts, leather bags, helmets, etc.They are ideal replacement parts for your bed frames, tables, chairs, cabinets, workbench, wood boards, wardrobes and so on..
Check StockM8-1.25 x 200mm/7.87\ Stainless Steel Fully Threaded Rod Right Hand Threads with Hex Nut Silver Tone (2 Set)
- Materia: Stainless Steel, provides great corrosion resistance and antirust ability for a long service life..
- Package Contents: 2 x Fully Threaded Rod with Hex Nut.
- Applications : Perfect for anchor bolts, clamps, hangers and U-bolts and many more projects where a metal rod with continuous threading or no head or fashioned tip is required..
Check Stock
LS1 Harmonic Balancer Installer Crank Pulley Installer Crankshaft Installation Tool For GM LS1/LS Engines 1997~Current
- Great Compatibility — Works on all GM LS & LT series engines 1997-current (Gen 3, 4, & 5)..
- Upgrade Design — Simply thread the tool into the crankshaft until it seats, then tighten the nut down until the pulley is seated. This is a must have for engine swaps or upgrading the balancer..
- Special Features — Includes 1×Threaded Rod, 1×Flange Nut and 2×Washers. Threaded rod is hardened 94 Rockwell and hardware is grade 10.9..
- Superior Quality — Premium grade heat-treat heavy duty steel, galvanized steel nuts and aluminum washers, durability, anti-corrosion and anti-rust. High precision and hardness to provide a much longer service life..
- 100% Satisfaction Guarantee — If you're not 100% satisfied with our tools, simply return it for a full refund in 30 days. Support 12 months’ Warranty. Professional & Sincere Service allows you to take no risks to purchase in E-cowlboy!.
Check Stock
55 Pack Miaozhun .223/5.56.300 Blackout Wool Star Chamber Cleaning Pads with Rod Fitting Adapter
- These pads are designed to clean the .223Cal/5.56mm/.300blk star chamber,the locking lugs recess on the barrel extension (bolt locking area) and the face of the chamber..
- Comes with a male adapter(including a nut to keep the pad on the rod adapter), which can be threaded onto any standard 8-32 gun cleaning rod..
- How to use: thread a star pad onto the cleaning rod adapter,use the nut to keep the pad tight fit on the rod adapter and insert into the chamber. The pad is cut to fit the locking lugs of the .223/5.56/.300 blk star chamber. You can then twist the rod/pad clockwise to wipe behind the lugs..
- It's better to apply some oil/solvent to soften the gunk/carbon on the chamber, then use the pads to clean,the pads absorb and holds cleaning solvent well..
- Made of high density compressed wool felt,pretty stiff. Much easier and efficient to cleaning the star chamber than using cleaning patches..
Check StockPrime-Line 9118861 K-Lock Nuts With External Tooth Washer, 1/4 inch-20, Zinc Plated Steel
- Hex nut with a built in free spinning external tooth lock washer.
- Teeth on lock washer help to lock nut into place.
- Screws onto a bolt, cap screw or threaded rod of the same thread size.
- Thread Type: Coarse, Thread Class: UNC-2B.
Check Stock
Angle Grinder Extension 5/8-11, 2 pcs 4-1/2 Inch Angle Grinder Lengthen Connecting Rod , 45# Black Steel Material, Seamless Docking, Easy Installation 80 mm *1 And 120 mm * 1
- Angle Grinder Extension Connecting Rod Size: 【Important】Before buying, please check the size, Fit for a spindle size of 5/8" - 11" and FIT FOR MOST 4-1/2"-5" Grinding Wheels, Inner thread 5/8" - 11", Outer thread 5/8" - 11",Overall length 80 mm * 1 + 120 mm * 1.
- Great for Deep Areas: The rotating extension shaft to use conveniently with 5/8" 11 threaded power tools. Can be used for grinding and polishing deep stones such as inside corners and special shapes..
- Easy To Install: ①Install the extension rod ②install the Grinder Inner Flange Nut ③install the Grinding Wheels ④install the Grinder Outer Flange Nut ⑤use the Spanner to fix the Grinder Outer Flange Nut..
- Material: Made of high quality carbon steel, more strength and resistance to deformation.The 2022 upgrade model improves the shortcomings of the previous product's shaking..
- Package Includes and Transportation : Angle Grinder Extension Connecting Rod *2 , Packaging: special plastic box packaging,We use the fastest express, usually 10-15 days to complete the delivery..
Check StockMroMax 10pcs M5x25mm Chicago Binding Screw Button Screw Nickel Plated Carbon Steel Phillips Head Binding Barrels and Screws Post Screw for DIY Leather Decoration Scrapbook Photo Albums Bookbinding
- Dimension: Nut's rod outer diameter: 5mm/0.2".
- Good Quality: Made of quality carbon steel material, nickel plated surface, sturdy and anti-rust, easy to bind, install and remove, can use repeatedly, good tightness..
- Easy to Use: Easily applied with standard screwdriver. Threaded post lets you open and re-attach piece where needed..
- Instructions: Make a hole larger than 0.5mm than the diameter of the nut rod, put screws and nuts on both sides of the locked object, and select the appropriate tool to lock it..
- Wide Application: Especially suit for leather handicrafts decoration, bookbinding, document, book, album, DIY crafts, etc..
Check StockPOWERTEC 71165 Aluminum Cam Clamp for Woodworking, 5/16”-18 Threaded Insert - 2PK
- This is for a set of hold down clamp for use with T-slot track.
- These clamps are useful in many woodworking & metalworking applications for work holding, positioning, and fixturing.
- Puts clamping pressure anywhere along the flush-mounted T-slot T-track.
- Slides into T-track & quickly secures with the turn of the hand knob nut.
- Both T-screw and threaded rod are of 8mm threaded.
Check Stock
