Reviews Thread Pipe Fitting

Joywayus Hex Nipple 1/2' Male x 1/2' Male Threaded Stainless Steel 304 Threaded Nipple Pipe Fittings for Brew Kit Home Piping (Pack of 5)

  • 【Size】1/2" Male x 1/2" Male Thread. Tapered thread. Pipe fittings are components used for connecting, terminating, controlling flow, and changing the direction of pipe..
  • 【High Quality Material &Threads】Made of quality stainless steel 304, durable and sturdy corrosion resistance, ductility at high temperatures, and low magnetic permeability. High quality and deep threads allow the fittings to bite better, tight threads, not easy to slip..
  • 【Hex Nipple】The hex nipple fitting is a short length of pipe with threaded ends for connecting threaded pipes, and it has a hexagonal section in the middle for an increased bearing surface when adjusting the fitting with a wrench..
  • 【Operating temperature range】Temperature rating: -65 to 250 degrees F.
  • 【Widely Applications】Male threads for connecting to female threaded pipes, this premium pipe fitting can be used to connect various pipes, such as air pipe, fuel pipe, water pipe as well as air tools.
  • it can also be used with grease, fuels, LP and natural gas, refrigeration, instrumentation and hydraulic systems in low and medium pressure pipe line connections..
Check Stock

6505-08-08 Hydraulic Fitting 1/2\ Female JIC Swivel X 1/2\ Male Pipe Carbon Steel

  • 6505-08-08 HYDRAULIC FITTING 1/2" FEMALE JIC SWIVEL X 1/2" MALE PIPE (Tube O.D. / Hose I.D. Size).
  • THREAD SIZES FOR 6505-08-08 HYDRAULIC FITTING 3/4"-16 FEMALE JIC SWIVEL X 1/2" MALE PIPE.
  • THIS PART NUMBER IS OFTEN REVERSED IN THE INDUSTY. PLEASE VERIFY THE THREAD SIZES BEFORE PURCHASING.
  • TO MEASURE THREAD SIZE, CALIPERS WORK BEST.
Check Stock

Class A Customs | T-1000-BPK| 10 Gallon Fresh Water Tank & Plumbing Kit RV Concession

  • 10 Gallon Fresh or Gray Water Holding Tank Manufactured by Class A Customs - Made from NSF Approved Materials - Fresh & Drinking Water Safe - Can be used for Fresh or Gray Water Storage.
  • WATER TANK MEASUREMENTS: 19” Longest Length (not including fittings) x 9” x 14” - Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement).
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads..
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process..
  • BASIC PLUMBING KIT INCLUDES - (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adaptor (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adaptor (TWO) 1.5” Hose Clamps (ONE) 1.5” Male Pipe Thre....
Check Stock

Class A Customs | T-2100-BPK| 21 Gallon Fresh Water Tank & Plumbing Kit RV Concession

  • 21 Gallon Fresh or Gray Water Holding Tank Manufactured by Class A Customs - Made from NSF Approved Materials - Fresh & Drinking Water Safe - Can be used for Fresh or Gray Water Storage.
  • WATER TANK MEASUREMENTS: 34” Longest Length (not including fittings) x 9” x 16” - Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement).
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads..
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process..
  • BASIC PLUMBING KIT INCLUDES - (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adaptor (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adaptor (TWO) 1.5” Hose Clamps (ONE) 1.5” Male Pipe Thre....
Check Stock

Class A Customs | T-4000-BPK| 40 Gallon Fresh Water Tank & Plumbing Kit RV Concession

  • 40 Gallon Fresh or Gray Water Holding Tank Manufactured by Class A Customs - Made from NSF Approved Materials - Fresh & Drinking Water Safe - Can be used for Fresh or Gray Water Storage.
  • WATER TANK MEASUREMENTS: 39 1/2” Longest Length (not including fittings) x 13” x 18” - Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement).
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads..
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process..
  • BASIC PLUMBING KIT INCLUDES - (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adaptor (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adaptor (TWO) 1.5” Hose Clamps (ONE) 1.5” Male Pipe....
Check Stock

Class A Customs | T-3000-BPK| 30 Gallon Fresh Water Tank & Plumbing Kit RV Concession

  • 30 Gallon Fresh or Gray Water Holding Tank Manufactured by Class A Customs - Made from NSF Approved Materials - Fresh & Drinking Water Safe - Can be used for Fresh or Gray Water Storage.
  • WATER TANK MEASUREMENTS: 34 1/2” Longest Length (not including fittings) x 12” x 17 1/2” - Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement).
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads..
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process..
  • BASIC PLUMBING KIT INCLUDES - (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adaptor (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adaptor (TWO) 1.5” Hose Clamps (ONE) 1.5” Male ....
Check Stock

Drill America DWTPT1/4-1-1/4SET 6 Piece NPT Pipe Tap Set in Wooden Case (1/4\

  • Carbon steel pipe taps are designed to clean and or re-thread damaged or jam pipe threads.
  • Also called 'pipe taps', National Pipe Taper (NPT) taps are appropriate for threading a wide variety of materials both ferrous and non-ferrous..
  • The nominal size of a Pipe Tap is that of the pipe fitting to be tapped, not the actual size of the tap..
  • The thread tapers 3/4 of an inch per foot. All Pipe Taps furnished with a 2-1/2 to 3-1/2 thread chamfer..
  • 6 Piece Set of Carbon Steel NPT Pipe Taps, Sizes /4.
Check Stock

Drill America - DWTPT1/8-1SET 6 Piece NPT Pipe Tap, Carbon Steel, DWTPT Series Set, 1/8\

  • Carbon steel pipe taps are designed to clean and or re-thread damaged or jam pipe threads.
  • Also called 'pipe taps', National Pipe Taper (NPT) taps are appropriate for threading a wide variety of materials both ferrous and non-ferrous..
  • The nominal size of a Pipe Tap is that of the pipe fitting to be tapped, not the actual size of the tap..
  • The thread tapers 3/4 of an inch per foot. All Pipe Taps furnished with a 2-1/2 to 3-1/2 thread chamfer..
Check Stock

Class A Customs | Under Mount 20 Gallon RV Concession Fresh and Gray Water Holding Tank & Plumbing Kit UM-2000-BPK

  • 20 Gallon Fresh or Gray Water Holding Tank Manufactured by Class A Customs - Made from NSF Approved Materials - Fresh & Drinking Water Safe - Can be used for Fresh or Gray Water Storage.
  • WATER TANK MEASUREMENTS: 48” Longest Length (not including fittings) x 8.5” x 13” - Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement).
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads..
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process..
  • BASIC PLUMBING KIT INCLUDES - (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adaptor (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adaptor (TWO) 1.5” Hose Clamps (ONE) 1.5” Male Pipe Th....
Check Stock

Class A Customs | Under Mount 30 Gallon RV Concession Fresh and Gray Water Holding Tank & Plumbing Kit | UM-3000-BPK

  • 30 Gallon Fresh or Gray Water Holding Tank Manufactured by Class A Customs - Made from NSF Approved Materials - Fresh & Drinking Water Safe - Can be used for Fresh or Gray Water Storage.
  • WATER TANK MEASUREMENTS: 48” Longest Length (not including fittings) x 8.5” x 20.5” - Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement).
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and water-tight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT Over-tighten fitting damage will occur – Use plastic threaded fittings, metal threads may damage tank fittings.
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process..
  • BASIC PLUMBING KIT INCLUDES: (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adaptor (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adaptor (TWO) 1.5” Hose Clamps (ONE) 1.5”....
Check Stock

uxcell PVC Barb Hose Fitting Connector Adapter 16mm or 5/8

  • APPLICATION.The adapter’s barbed fitting creates a tight seal on flexible PE pipe when used with a hose clamp (sold separately)..
  • ADVANTAGE.An O-ring is delivered to the end of each joint thread, eliminating the need for a sealant or raw tape.
  • HIGH QUALITY MATERIAL. made of PVC ,have Alkali resistance, high temperature resistance, corrosion resistance, strong anti-aging, high strength, no break..
  • -30 degree to 100 degree F temperature range..
  • BARB HOSE FITTING.has a male National Pipe Thread (G) thread on one end and a barbed insert on the other.
  • Size: 16mm or 5/8″ Barb x 3/4″ G Male.
Check Stock

SUPPLY GIANT OQCM2025-5 Nipple pipe, 2 in. x 2-1/2 in, Black, 5 Pack

  • PIPE NIPPLE TYPE: pipe nipple fitting male NPT (National Pipe Thread) thread made of superior coating steel for commercial use residential application and all your DIY projects. Black coated schedule 40, 150 PSI.
  • PIPE FUNCTION: nipple joins two pipes or extending length.
  • HIGH QUALITY: durable pipe steel material manufactured using advanced technology.
  • RATING APPROVAL: meets ASTM and ANSI standards.
  • DECORATIVE USES: pipes can be used for decorative purposes for industrial feel in room décor, furniture shelves and accessories.
Check Stock

Class A Customs | 25 Gallon RV Concession Fresh Water Tank with Plumbing Kit & 12 Volt Water Pump | T-2500-BPK-PUMP

  • 25 Gallon Fresh Water Holding Tank Manufactured by Class A Customs - Made from NSF Approved Materials - Fresh & Drinking Water Safe WATER TANK MEASUREMENTS 33.5” Longest Length (not including fittings) x 10” x 17”- Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement).
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads..
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process..
  • BASIC PLUMBING KIT INCLUDES - (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adaptor (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adaptor (TWO) 1.5” Hose Clamps (ONE) 1.5” Male Pipe Thread PVC Male Adaptor (ONE) 5ft. Section of 0.5” ID V....
Check Stock