Reviews Taper Reamer Bit

5/8 Drill Bridge/Construction Reamer with 1/2 Shank Chuck,HSS Taper Bridge Reamer Bit Tool for Steel Metal Wood Alloy to Align Existing Hole and Enlarge Hole

  • The heavy duty high-speed steel bridge reamer is also called construction reamers,it used for aligning an existing hole and enlarging undersized hole prior to bolt or rivet installation.Our reamer bit aligns and enlarges pre-drilled holes ready for bolting..
  • Makes reaming holes out extremely easier than using large drill bits,the reamed hole is smooth without tear-outs. But there must be a existing hole or a pilot hole that is smaller than 5/8" before using our 5/8" Bridge/Construction Reamer..
  • The tapered point design permits the reamer bit to enter into the overlapping holes of out-of-line,make the bolt holes line up.Enlarging the holes in the steering knuckles and pitman arm..
  • The 5/8" bridge reamer bit is not a drill bit,only aligning reamer to aligh holes which are pre-drilled.If you need to expand a hole to 5/8". At first there must be a 3/8" pre-drilled hole,then ream out to 5/8"..
  • Commonly used in bridge,construction,steel erection and automotive truck trailer industries,specially use in structural materials such as steel, metal, alloy aluminum,brass,plastic,iron,nickel,copper,cast iron etc.Three symmetrically placed flats on shank provide positive grip in portable electric and pneumatic tools..
Check Stock

2Pcs High Carbon Steel Straight Shank Morse Taper Reamer Rough + Fine Hand Reamer Set Replacement(MT2#)

  • HIGH QUALITY-- Morse Taper Reamer is made of high carbon steel, it is not easy to wear and has a long service life..
  • 2PCS-- Each set of two reamers, one rough and one fine, meets different work requirements..
  • APPLICATION-- Available in a variety of models to meet most daily work needs. A perfect replacement for the broken or worn one..
  • GOOD PERFORMANCE-- Morse Taper Reamer features fine workmanship, high precision, high cutting efficiency..
  • 5 OPTIONAL MADEL-- Optional Model: MT1#, MT2#, MT3#, MT4#, MT5#, meet your different requirements.
Check Stock

2/0 Taper Pin Reamer Kit

  • 1 - 2/0 Spiral Flute taper reamer (Bosnian made).
  • 5 - 300 series Stainless steel 2/0 taper pins 3/4" long.
Check Stock

5/8\ Expansion Reamer, Carbide Tipped, Tapered Shank, 56059, USA Made

  • When the diameter wears down to the low limit, it may be expanded oversize, reground to size and recleared. The expansion screw should never be loosened in an attempt to use the reamer for a size smaller than that to which the tool was originally finish ground. These reamers are inteded to be used for 1 specific diameter, not multiple diameters..
  • Morse taper shank #2, For Reaming Abrasive Material.
  • This is an expansion reamer NOT an adjustable reamer. It can be expanded only and reground..
Check Stock

29/32\ Expansion Reamer, Carbide Tipped, Tapered Shank, 56068, USA Made

  • When the diameter wears down to the low limit, it may be expanded oversize, reground to size and recleared. The expansion screw should never be loosened in an attempt to use the reamer for a size smaller than that to which the tool was originally finish ground. These reamers are inteded to be used for 1 specific diameter, not multiple diameters..
  • Morse taper shank #2, For Reaming Abrasive Material.
  • This is an expansion reamer NOT an adjustable reamer. It can be expanded only and reground..
Check Stock

7/8\ Expansion Reamer, Carbide Tipped, Tapered Shank, 56067, USA Made

  • When the diameter wears down to the low limit, it may be expanded oversize, reground to size and recleared. The expansion screw should never be loosened in an attempt to use the reamer for a size smaller than that to which the tool was originally finish ground. These reamers are inteded to be used for 1 specific diameter, not multiple diameters..
  • Morse taper shank #2, For Reaming Abrasive Material.
  • This is an expansion reamer NOT an adjustable reamer. It can be expanded only and reground..
Check Stock

3/4\ Expansion Reamer, Carbide Tipped, Tapered Shank, 56063, USA Made

  • When the diameter wears down to the low limit, it may be expanded oversize, reground to size and recleared. The expansion screw should never be loosened in an attempt to use the reamer for a size smaller than that to which the tool was originally finish ground. These reamers are inteded to be used for 1 specific diameter, not multiple diameters..
  • Morse taper shank #2, For Reaming Abrasive Material.
  • This is an expansion reamer NOT an adjustable reamer. It can be expanded only and reground..
Check Stock

7/8\ Expansion Reamer, Carbide Tipped, Straight Shank, 56017, USA Made

  • When the diameter wears down to the low limit, it may be expanded oversize, reground to size and recleared. The expansion screw should never be loosened in an attempt to use the reamer for a size smaller than that to which the tool was originally finish ground. These reamers are inteded to be used for 1 specific diameter, not multiple diameters..
  • Morse taper shank #2, For Reaming Abrasive Material.
  • This is an expansion reamer NOT an adjustable reamer. It can be expanded only and reground..
Check Stock

15/16\ Expansion Reamer, Carbide Tipped, Tapered Shank, Partial Flute Carbide 56069P, USA Made

  • When the diameter wears down to the low limit, it may be expanded oversize, reground to size and recleared. The expansion screw should never be loosened in an attempt to use the reamer for a size smaller than that to which the tool was originally finish ground. These reamers are inteded to be used for 1 specific diameter, not multiple diameters..
  • 1 1/2 " flute length, Partial Flute Length Carbide.
  • Morse taper shank #3, For Reaming Abrasive Material.
  • This is an expansion reamer NOT an adjustable reamer. It can be expanded only and reground..
Check Stock

29/32\ Expansion Reamer, Carbide Tipped, Tapered Shank, Partial Flute Carbide 56068P, USA Made

  • When the diameter wears down to the low limit, it may be expanded oversize, reground to size and recleared. The expansion screw should never be loosened in an attempt to use the reamer for a size smaller than that to which the tool was originally finish ground. These reamers are inteded to be used for 1 specific diameter, not multiple diameters..
  • 1 1/2 " flute length, Partial Flute Length Carbide.
  • Morse taper shank #2, For Reaming Abrasive Material.
  • This is an expansion reamer NOT an adjustable reamer. It can be expanded only and reground..
Check Stock

13/16\ Expansion Reamer, Carbide Tipped, Tapered Shank, Partial Flute Carbide 56065P, USA Made

  • When the diameter wears down to the low limit, it may be expanded oversize, reground to size and recleared. The expansion screw should never be loosened in an attempt to use the reamer for a size smaller than that to which the tool was originally finish ground. These reamers are inteded to be used for 1 specific diameter, not multiple diameters..
  • 1 3/8 " flute length, Partial Flute Length Carbide.
  • Morse taper shank #2, For Reaming Abrasive Material.
  • This is an expansion reamer NOT an adjustable reamer. It can be expanded only and reground..
Check Stock

1 7/16\ Expansion Reamer, Carbide Tipped, Tapered Shank, Partial Flute Carbide 56080P, USA Made

  • When the diameter wears down to the low limit, it may be expanded oversize, reground to size and recleared. The expansion screw should never be loosened in an attempt to use the reamer for a size smaller than that to which the tool was originally finish ground. These reamers are inteded to be used for 1 specific diameter, not multiple diameters..
  • 2" flute length, Partial Flute Length Carbide.
  • Morse taper shank #4, For Reaming Abrasive Material.
  • This is an expansion reamer NOT an adjustable reamer. It can be expanded only and reground..
Check Stock

1 5/16\ Expansion Reamer, Carbide Tipped, Tapered Shank, Partial Flute Carbide 56078P, USA Made

  • When the diameter wears down to the low limit, it may be expanded oversize, reground to size and recleared. The expansion screw should never be loosened in an attempt to use the reamer for a size smaller than that to which the tool was originally finish ground. These reamers are inteded to be used for 1 specific diameter, not multiple diameters..
  • 1 7/8 " flute length, Partial Flute Length Carbide.
  • Morse taper shank #4, For Reaming Abrasive Material.
  • This is an expansion reamer NOT an adjustable reamer. It can be expanded only and reground..
Check Stock