Reviews Stepper Motor Drive

LAFVIN 5 Sets 28BYJ-48 ULN2003 5V Stepper Motor + ULN2003 Driver Board for Arduino

  • Stepper motor with a standard interface..
  • A, B, C, D four-phase LED indicates the status of the stepper motor work..
  • Drive Module Board Size(in): 1.37*1.18*0.6.
  • 5 line 4 phase can be used for ordinary ULN2003 chip driver, connect to the 2 phase , support the development board，With convenient use, direct docking.
  • Package Content: 5 set 28BYJ-48 Stepper Motor + Uln2003 Driver Board +20pcs female to male Dupont cable (as a gift).
Check Stock

CenryKay 5pcs ULN2003 28BYJ-48 4-Phase Stepper Motor with 5V Drive Board and 10pcs Dupont Wire Male to Female Breadboard Jumper Wires Compatible with Arduino

  • A, B, C, D four-phase LED indicates the status of the stepper motor work..
  • Stepper motor with a standard interface, when used directly pluggable..
  • The motor is gear-reduced, the noise is extremely low, and it can be driven with 5V running smoothly..
  • Drive Module Board Size(in): 1.37*1.18*0.6.
  • Great packing in a box : 5 set Uln2003 Stepper Motor + Driver Board+Dupont Wire ..
Check Stock

6 PCS 28BYJ-48 ULN2003 5V Stepper Motor + ULN2003 Driver Board for Arduino

  • ❃❃ The stepping motor is a kind of mechanical and electrical device that converts electrical pulses into angular displacement. Come with a standard interface, when used directly pluggable..
  • ❃❃ Drive Module Board Size(in): 1.37 * 1.18 * 0.6(in).
  • ❃❃ A, B, C, D four-phase LED indicates the status of the stepper motor work..
  • ❃❃ 5 line 4 phase can be used for ordinary ULN2003 chip driver, Connect to the 2 phase, Support the development board, With convenient use, direct docking..
  • ❃❃ Great packing in a box : 6 PCS ULN2003 Stepper Motor + Driver Board (with a little gift)..
Check Stock

Longruner 5X Geared Stepper Motor 28byj 48 Uln2003 5v Stepper Motor Uln2003 Driver Board with ArduinoIDE (no Wire)

  • 5pcs Stepper motor and driver board compatible with 2560 1280 DSP ARM PIC AVR STM32 Raspberry Pi..
  • Stepper motor with a standard interface. A, B, C, D four-phase LED indicates the status of the stepper motor work..
  • Motor diameter: 1.1 inches.Wire length：9.05 inchs. Stepping angle: 5.625 x 1/64.Reduction ratio: 1/6.Drive Module Board Size:1.26 inchsX1.38inchs. Cable length: about 20cm /8-inch..
  • Great packing in a box : 5 set Uln2003 Stepper Motor + Driver Board..
Check Stock

Twotrees Stepper Motor Driver, TB6600 4A 9-42V Nema 17/23 CNC Controller Single Axes Hybrid - Upgraded Version

  • 【1】Package included: 1 x Stepper Motor Driver,1 x Stepper Motor, 1 x Wire..
  • 【2】Suitable for a wide range of stepper motors from NEMA size 17,23 and 24 (42 * 42mm to 60 * 60mm). It can be used in various types of machines, such as XYZ tables, labellers, laser cutters, engraving machines, pick-place devices and so on..
  • 【3】Motor driver: 9V-42V DC power supply, H-bridges bipolar constant phase current drive. The maximum 4.0A of the eight types of output current..
  • 【4】The largest 32 divisions of the 6 models are optional.
  • Suitable for 4 wires, 6 wires and 8 wires stepper motor..
  • 【5】Protect form: Overheated protection, overcurrent protection, undervoltage protection, prevention of inversion..
Check Stock

CNC Control Board, MYSWEETY GRBL 3 Axis Engraving Machine Controller Board for DIY Mini CNC Wood Router Engraver Machine

  • Software: GRBL controller, Universal Gcode Sender..
  • Support XYZ three-axis control, spindle..
  • Support stepper motor: 12V, the maximum current within 2A, recommended within 1.5A and additional heat. (Any stepper motor 42, 57)..
Check Stock

8PCS L298N Motor Drive Controller Board Dual H Bridge DC Robot Stepper Motor Compatible with Ardu-ino Electric Projects, Smart Car Robot

  • Dual-channel H-bridge driver working mode creates higher working efficiency,L298N as main chip, Can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors..
  • The L298N driver module, using L298N chip can directly drive two 3-30V DC motor, and provides a 5V output interface, you can chip circuitry to 5V power supply, support 3.3VMCU control, you can easily control the DC motor speed and direction, you can also control the 2-phase stepper motor, smart car essential..
  • Terminal driver part of the supply area VMS: +5V ~ +35V.
  • Drive part of the peak current Io: 2A / Bridge.
  • Logical part of the terminal power supply range Vss :4.5-5 .5V.
  • Logical part of the operating current range: 0 ~ 36mA.
  • The control signal input voltage range: 4.5-5.5V low 0V high.
  • To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage.
  • High working power to 46v, large current can reach 3A MAX and continue current is 2A, power to 25w..
  • Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability, large capacity filter capacitance,afterflow protection diode, more stable and reliable..
Check Stock

KOOKYE 2 x 28BYJ-48 DC 5V Stepper Motor + ULN2003 Driver Test Module Board for Arduino Raspberry Pi

  • This is a stepper motor and a stepper motor driver..
  • Mainly used in air conditioner louver, small cooling and heating fan etc. Stable and all technic parameters are qualified for national electronic....
  • On-board ULN2003A chipset,On-board 4-way indicator light,On-board XH-5P socket,Compatible with Arduino..
Check Stock

MINARIK MM23001C 0-90/0-180V-DC 1/4-2HP 5A AMP DC MOTOR DRIVE D506404

  • Motor Driver: 9V-42V DC power supply, H bridge bipolar constant phase flow drive. The maximum 4.0A of the eight kinds of output current..
  • Motor Driver: Energy-saving semi-automatic current lock function, built-in temperature protection and over current protection.The largest 32 subdivision of the 6 models are optional..
  • Package: TB6600 stepper motor driver + nema 17 stepper motor + mounting bracket + inner hexagon spanner + M3/M4 screws.
  • Strive for 100% service satisfactory, any question or problem please do not hesitate to contact us, we are always happy to help..
Check Stock

AOICRIE 4PCS L298N Motor Drive Controller Board Module Dual H Bridge DC Stepper for Arduino

  • L298N as Main driver chip L298N, strong driving ability, strong anti-interference, low calorific value, afterflow diode protection, more stable and reliable for Arduino projects, Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability..
  • Double H bridge design, can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors, high efficient, To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage..
  • Driving DC motor Because the module is drived by double H bridge,it can drive two motors simultaneously.Input the following driving timing from IN1-IN4 then the speed and direction of the stepper motor can be controlled..
  • Easy to Use No assembly required. This L298N board comes ready to go. Just wire up motors and power, easy to use..
  • Wide Usage Great for DIY Smart Car Robot Power MEGA R3 for Mega2560 Duemilanove, if driving voltage is more than 12V, use external standard 5volt TTL outputs to switch the H-bridge circuits..
Check Stock

DEVMO 5pcs DRV8825 Stepper Motor Driver Module with Mini Heat Sink for 3D Printer Accessories Compatible with RepRap 4 RAMPS 1.4 StepStick

  • ★The DRV8825 stepper motor driver carrier board TI DRV8825 micro bipolar stepper motor drive is a breakthrough..
  • ★Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step..
  • ★Simple step and direction control interface..
Check Stock

SainSmart Genmtisu CNC Router Machine Controller Board with ABS Case for CNC 1810-PRO/3018/3018-PRO

  • This controller board is designed for Genmitsu CNC Router 1810-PRO, 3018, and 3018-PRO. It can perfectly compatible with SainSmart Blue Laser Module..
  • Software: GRBL controller, UniversalGcodeSender..
  • Support XYZ three-axis control, spindle and laser module. Support 3 pin and 2 pin lasers (the 2 pin lasers: please connect the white interface " + s-")..
  • Support stepper motor: 12V, the maximum current within 2A, recommended within 1.5A and additional heat. (Any stepper motor 42, 57)..
Check Stock

MACH3 Controller USB MACH3 100Khz Motion Controller Card Breakout Board Controller Card for CNC Engraving Servo Motor Stepper Motor Servo motor

  • 【Functions】The function of this motion control card includes that it supports automatic probe tool, emergency input, limit switch, and supports....
  • 【4-axis Linkage】Usb interface board supports for 4-axis linkage, you can connect four stepper motor drives or servo drives. 4 general-purpose....
  • 【Wide Use】The maximum step-pulse frequency of motion control card is100KHz, which is very suitable for CNC Engraving, Servo Motor, Stepper Motor....
  • 【Advantage】The motion controller needs using external 24V DC power to isolate USB and external port, and to make the system more stable. And it....
  • 【Drive Output Interface】The 4 general-purpose isolated relay drive output interface can drive four relays for controlling the spindle starts,....
Check Stock