Reviews Ss302 Flange

Slotted Shim Kit 3 x 3\

• Tensile Strength (PSI): 185,000 P.S.I. (MIN) for 302SS & 75,000 P.S.I. (MIN) for 304SS.
• Application: Used For Alignment, Leveling and Spacing of Pumps, Motors, Compressors, Generators And Other Plant Machinery.

Antsky 4x4(Actual: 3.5x3.5) 4-Way Right Angle Corner Brackets with Flange Anchor Bases，Stainless Steel Pergola/Gazebo Kit Hardware(2 Pack)

• Material：304 stainless steel, black finishing；.
• Actual inner size：3.6×3.6inch（91.5mm）,This size applies to nominal standard 4"x 4" wooden post (actual 3.5"x 3.5" post on market).
• there is a slight error in the actual size, usually the error is about 1mm.
• Each angle of corner connector is 90 degrees.
• This package comes with two 4-way right angle corner brackets, 2 post flange anchors, 80 SS hex screws and 8 SS concrete anchor bolts.
• This 4-way corner brackets are multi-functional, can be used for building pergola、gazebo，playhouse、tree houses、log cabin and so on；.
• These 4-way right angle corner brackets and the flange anchors make the installation very simple and easy. It's made of stainless steel, which is very sturdy and anti-rusty. The structure designed for covering the whole end of wood beam, so that the wood won't rot by years of rain and sun..

Sterling Seal 9000IR3304GR1500x24 304 Stainless Steel Spiral Wound Gasket with 304SS Inner Ring and Flexible Graphite Filler, Pressure Class 1500#, for 3\ Pipe, Yellow with Grey Stripe (Pack of 24)

• Sterling Seal & Supply Style 9000IR - 304 Stainless Steel Spiral Wound Gaskets with 304SS Inner Ring are suitable for use with flat face and raised face flanges.
• Gasket identification markings required by ASME B16.20 clearly etched in all gaskets. These gaskets Excel in the prevention of flange Erosion, inward buckling and reduction of turbulent flow.
• Installation tip: spiral wound gaskets with internal or external guide Rings should be fully compressed to the guide ring. This will NOT damage the gasket or affect the sealing performance.
• Installation tip: check that flange faces are clean and in good condition. Ensure correct bolting material is utilized to suit the operating conditions, and the use of Bolt lubrication is employed.

Exhaust Header Manifold For Chevrolet LS1 LS6 LSX V8 Turbo+2 x Elbows T3 T4 To V Band 3.0

• Huge 1 3/4" Stainless Primary Tubes (true 1 3/4 unlike the others listing the same header by multiple companies with multiple sizes).
• 7/16" Thick Flanges 3" V-Band Collectors, CNC Mandrel Bent Pipes for Excellent Flow, 4 to 1 Header Design to Create a Compact Package for Universal.
• T3 : hole to hole 45*86mm/T4 : hole to hole 70*83mm/V band Flange 80mm ID 93mm OD.Cast Turbo Elbow Adapter T3 T4 to 3" V-Band SS304.
• 304 Stainless Steel Cast and Machined Adapter, with Tight Radius. Works for Many Turbo Applications. V band Flange Allows Rotation of the Turbo At Any Angle. Flange Is Threaded with 4 M10x1.5 Holes.
• Application : Small Block V8 LS1/LS2/LS3/LS6 LSX 4.8L, 5.3L, 5.7L, 6.0L, 6.2L.

K5AWW Replacement Wire Whip for 5 Quart Lift Bowl 6-Wire Whip Attachment

• 6-WIRE WHIP: quickly incorporates air into ingredients for fluffy whipped cream, perfect boiled frostings and cakes with whipped egg whites.
• RUSTPROOF&BURNISHED: made of high quality durable stainless steel, which is Hand wash only, stainless steel wire tines, aluminum flange.(Hand Wash....
• GOOD CAPABILITY: fits KitchenAid K4, K4SS, K5, K5A, K5SS, KG25G7X, KG25H0X, KG25H3X, KP50,KP50PS, KSM455, KSM5, KSM50, KSM500PS, KSM450, KSM50HDP,....
• MEASURES: 7.25" in total length and Wide 5in.
• GUARANTEE: 100% satisfaction customer care and money back warranty.

1/4 -20 x 1 Flanged Capacitor Discharge cd Welding Studs Aluminum Quantity 100 pieces

Remflex 3003 Exhaust Gasket for Ford V8 Engine, (Set of 2)

• 1-1/8 inch width x 1-1/2" height Stock Square Port.
• Ford V8 - 302 ('81-'95), 351 ('69-'97) Windsor, 1-1/8" x 1-1/2" Square Port, Manifold or Headers, 2/Set.
• Heating and cooling of the exhaust system causes header and manifold flanges to warp resulting in gaps between the head and header which Remflex exhaust gaskets seal completely due to the thickness and compressibility of the 100 percent flexible graphite.
• Remflex exhaust gaskets come in a standard 1/8 inch thickness and are designed to crush 50 percent allowing them to fill any pits or gaps in the flange surface up to 1/16 inch.
• The aluminum cylinder head and steel header or manifold combination are configurations that readily cause gap issues in the mating flanges due to contraction and expansion of the dissimilar materials.
• Remflex exhaust gaskets fill those gaps permanently.
• There are no rubber binders or composite materials in Remflex exhaust gaskets so they will not shrink or harden due to time or temperature eliminating the need to go back and continually retighten your flange bolts.

Bodeman - 2 Front CV Axle Assembly and 2 Front Wheel Hub Bearing Assembly for Models w/AUTO-TRANS. ONLY - 05-10 Chevy Cobalt (NO-SS)/ 06-11 Chevy HHR (NO-SS)/ 09-10 Pontiac G5

• Front CV axle and Wheel Hub Bearing Assembly for Chevy Cobalt, Chevy HHR Models w/A.T. Only - EXCLUDING SS.
• SAME DAY SHIPPING! STOCK IN NEW YORK, USA! Located in Jamaica, NY, USA, Bodeman Is a Company Servicing Auto-shops and Dealerships with OE Quality Replacement Parts.
• Lifetime Warranty on all internal parts!.

DERNORD Stainless Steel 304 Single Pin Heavy Duty Tri Clamp with Wing Nut for Ferrule TC 1.5 Pack of 10

• Tube OD: 1 Inch to 1-1/2 Inch, Flange Size: 50.5MM, Fits 1.5 Inch Tri-clamp.
• Made of stainless steel 304,Higher corrosion resistance than the 302 grade stainless steel.
• Preventing rust processes and for the whole body.
• Fit for all other homebrew stuff sanitary fittings.

Remflex 2004 Exhaust Gasket for Chevy V8 Engine, (Set of 2)

• Chevy V8 - SB 262, 265, 267, 283, 302, 305, 307, 327, 350, 400, ('55 - '00), Round Port, Headers, 2/Set.
• Port configuration comparable to Fel-Pro 1426.
• There are no rubber binders or composite materials in Remflex exhaust gaskets so they will not shrink or harden due to time or temperature eliminating the need to go back and continually retighten your flange bolts.
• Heating and cooling of the exhaust system causes header and manifold flanges to warp resulting in gaps between the head and header which Remflex exhaust gaskets seal completely due to the thickness and compressibility of the 100 percent flexible graphite.

Remflex 2006 Exhaust Gasket for Chevy V8 Engine, (Set of 2)

• 1-3/8 inch width x 1-1/2 inch width Square Port - Matches the Stock cast iron Head Port.
• Chevy V8 - SB 262, 265, 267, 283, 302, 305, 307, 327, 350, 400, Stock Port, Manifold or Headers, 2/Set.
• Port configuration comparable to Fel-Pro 1404.
• There are no rubber binders or composite materials in Remflex exhaust gaskets so they will not shrink or harden due to time or temperature eliminating the need to go back and continually retighten your flange bolts.
• Heating and cooling of the exhaust system causes header and manifold flanges to warp resulting in gaps between the head and header which Remflex exhaust gaskets seal completely due to the thickness and compressibility of the 100 percent flexible graphite.

Golden Flame 25' Round Drop-in Fire Pit Pan w/18 Round Fire Ring Burner Installed (304 Series SS)

• 25" Round x 2.5" Deep SS Drop-In pan (with 1-1/4" support Flange) Includes installed 18" Fire Ring Burner.
• Extra Thick 304-Series Stainless Steel (42% Thicker than most major Brands).
• Holes are Machine Drilled and not punched. (Punched holes can cause a loud whistle).
• 1/2" welded male fitting in bottom center of pan for easy Installation (Recommended Cutout Dimensions: 25 1/2" Diameter).
• 10 Year Warranty (Twice as long as other major Brands).

Z Whip LS Oil Pump Pickup Tube Girdle Pipe Hold Down Brace Support Billet Bracket MADE IN THE USA Compatible with GM Chevy LS Series Engines LSX LS1 LS3 LS2 LQ4 LS6 LQ9 5.3L 6.0L 6.2L

• Compatible with all LS Series Engines 1997-2014 (GEN. III/IV small block chevy).
• The factory oil pickup tube on LS engines is only secured by one bolt. This can potentially lead to a poor seal on the oil pump. Our Billet aluminum Oil pump girdle solves the issue by placing a clamp on both sides of the tube, securely holding it in place..
• DOES NOT fit any LS oil pickup tube with welded flanges (GM # 12608593, Holley 302-1 and similar tubes). DOES NOT fit pickup tubes with two screw holes on their flange (Holley 302-2 tube and similar tubes)..
• Proudly made in the USA from Aerospace Grade Billet Aluminum.
• We are an AS9100D and ISO 9001:2015 Certified Manufacturer. Parts we produce fly at 30,000 feet where failure is not an option..