Reviews Spring Inside Installed

Valve Spring Shim - 1.500\ OD.645\ ID .060\ Thickness

  • Must-Have for Your Next Engine Build or Spring Upgrade - Production tolerances in cylinder heads, valve lengths, valve springs, retainers and locks can impact the valve spring installed height from valve to valve, greatly impacting spring seat and open pressures. COMP Cams spring shims are a must-have to ensure precise installed height on intake and exhaust valves..
  • Guaranteed Precision - COMP Cams shims are crafted from the finest shim stock steel to precise dimensions, ensuring consistent installed height adjustments from the first valve to the last..
  • Race Tough - COMP Cams valve spring shims are not only made from the highest quality shim stock available, they are also heat treated to withstand the most radical camshaft profiles..
  • 1.500" Outside Diameter, 0.645" Inside Diameter. Includes 1 0.060" Thick Shim..
  • Recommended for use with our 916, 26056, 917, 928, 929, 924, 925, 911, 954, 936, 938, 930, 953, 999, 26094, 943, 26055, 939, 927, 919, 933, 935, 944, 26095, 26097, 932, 26089,955, 26115, 26099 and 26547 springs..
  • Available in an assortment pack under part number 4757..
Check Stock

Draft Blocker 4 Inch - Backdraft Damper - Draft Stopper - Backflow Preventer - Vent Deflector (4'' Inch)

  • Back draft damper is made for insertion into inch ventilation ducts. The backflow damper RKI opens and closes automatically. It has a strong spring and can be installed either horizontally or vertically. The flap is suitable for retrofitting, since it is completely inside the duct.
  • Damper has 2 valves, designed for use in air conditioners (AC), dryers, exhaust, extractor or range hoods, heating ducts, vents and other HVAC applications.
  • INSTALLATION: The backflow flap is installed by inserting it into the ventilation pipe until it stops. The position of the spring should be horizontal for horizontal installations so that it can open and close optimally. The Backdraft shutter is installed so that the damper blades open only in the outflowing air direction..
  • The backflow flap opens and closes automatically at low air volumes. It has a smooth-running spring and an internal foam strip to keep the blades from rattling and can be installed horizontally or vertically.
  • Back draught valves can be inserted into ventilation ducts which are flexible or non flexible. Cannot be used with plastic ....
Check Stock

COMP Cams 4705-16 ID Spring Locator Set of 16-1.300\ OD.570\ ID.060\ Thickness

  • ... shims will not hold up to extreme spring pressures and high RPM's found in today's street and racing engines. COMP's hardened steel alloy seat ensures spring stability, durability and high RPM performance..
  • Fewer Shims, More Stability - Stacking shims is not the best way to set up valve springs to their appropriate installed height. Since they are available in multiple locator thicknesses, these locators eliminate the need to stack shims, while also adding to valvetrain stability and durability..
  • Protect Your Head - Valve springs should never be installed directly on aluminum heads. Protect your expensive cylinder heads by installing springs on our hardened steel spring locators..
  • Made to Measure - Made for both factory and aftermarket cylinder head dimensions, these spring seats are available for nearly any engine. With options in multiple O.D.'s (outside diameters), I.D.'s (inside diameters) and thicknesses, COMP has a locator to fit your valvetrain project..
  • Precision Machined for Consistency - Crafted in-house, using the best machining equipment, COMP Cams seats and locators are precision machined to ensure consistent thickness and inside/outside diameters for a perfect fit everytime..
  • Quality Guaranteed - COMP Cams' valve spring locators are made fr....
Check Stock

Draft Blocker - 4'' Inch Backdraft Damper Duct - Draft Stopper - Backflow Preventer - Inline Fan Vent - Vent Deflector (4'' Inch)

  • Back draft damper is made for insertion into inch ventilation ducts. The backflow damper RKI opens and closes automatically. It has a strong spring and can be installed either horizontally or vertically. The flap is suitable for retrofitting, since it is completely inside the duct.
  • Damper has 2 valves, designed for use in air conditioners (AC), dryers, exhaust, extractor or range hoods, heating ducts, vents and other HVAC applications.
  • INSTALLATION: The backflow flap is installed by inserting it into the ventilation pipe until it stops. The position of the spring should be horizontal for horizontal installations so that it can open and close optimally. The Backdraft shutter is installed so that the damper blades open only in the outflowing air direction..
  • The backflow flap opens and closes automatically at low air volumes. It has a smooth-running spring and an internal foam strip to keep the blades from rattling and can be installed horizontally or vertically.
  • Back draught valves can be inserted into ventilation ducts which are flexible or non flexible. Cannot be used with plastic ....
Check Stock

RKI 4" - Professional Backdraft Damper Inline Spring Loaded for Dryer Duct

  • Back draft damper for insertion into 4 inch ventilation ducts. The backflow damper RKI opens and closes automatically. It has a strong spring and can be installed either horizontally or vertically. The flap is suitable for retrofitting, since it is completely inside the duct.
  • A tight sealing and fastening of the duct is achieved by the rubber strip attached to the outside of the draft blocker damper. The rubber seal prevents loud rattling when the flap blades open and close. The housing of the flap is made of galvanized steel, the flap blades are made of aluminum, the axle and spring are made of stainless steel.
  • Designed for use in AC, dryers, exhaust, extractor or range hoods, heating systems, vents and other residential, commercial and industrial HVAC applications.
  • FUNCTIONALITY: Duct draft stopper prevent cold air or wind from entering the ventilation pipe. In this case, the flap is installed in such a way that the flap leaves only open into the outgoing air direction. This means that no (cold) air / wind can penetrate the ventilation pipe from the outside..
Check Stock

Southco Flush Pull Latch Non Locking Black - M1-64

  • Installs easily from front of panel through single round-hole, and attaches from rear with mounting bracket and hardware.
  • Fits flush to panel when installed, with minimal protrusion inside of cabinet..
  • Min. Outer Panel Thickness - 17 mm (0.67 in) - Max Outer Panel Thickness - 22 mm (0.87 in) &.
  • Spring-loaded handle helps prevent rattle and Inside actuation allows opening latch from interior of compartment.
Check Stock

Vent Systems 8 Inch Backdraft Damper - Backflow Shutter - Heavy-Duty Inline Springs Loaded - One-Way Airflow Ducting Insert - Inline Fan Vent Deflector

  • Back draft damper for insertion into 8 inch ventilation ducts. The backflow damper opens and closes automatically. It has a strong spring and can be....
  • A tight sealing and fastening of the duct is achieved by the rubber strip attached to the inside of the draft blocker damper. The rubber seal prevents....
  • Designed for use in AC, dryer vent, exhaust, extractor or range hoods, heating systems, fans, vents and other residential, commercial and industrial....
  • Duct draft stopper prevent cold air or wind from entering the ventilation pipe. In this case, the flap is installed in such a way that the flap leaves....
  • The backflow Preventer valve is installed by pushing it into the ventilation pipe as far as it will go. The position of the spring should be....
Check Stock

HOMOTEK 12 Pack Spring Door Stopper With Rubber Bumper Satin Nickel 3-1/8\ Flexible Spring Heavy Duty Wall Door Stop Low Mounted Door Bumper For Home (Satin Nickel-Upgrade)

  • ...WALLS from marks, scrapes, also prevents walls from doorknob holes..
  • VERY EASY TO INSTALL AND REPLACe - Our Doorstop Is Extremely Easy To Install Within 1 Minute. The Door Stop Spring Is 3 ⅛ Inches And Comes With Mounting Screws,Anchors And Bases. All You Need Is a Screwdriver Or Driller.Our Door Stops Can Be Installed Into Your Baseboards Or Directly On Your Doors Simply By Using The Included Screws, Which Are Conveniently Located Inside Of The Base Plate Of Each Door Stop.And With The Anchor, This Door Stop Can Also Applied On Concrete Wall..
  • ENOUGH QUANTITY FOR USE - 12 Pieces In Total.Use Them Behind Every Door In Your Home To Beautifully Match All Of Your Other Satin Nickle Home Accessories And Decoration. You Can Even Give Them To Family Or Friends For The Perfect Housewarming Gift..
  • PRODUCT DIMENSION - Complete with a 13/16”Screw and 15/16” Metal Base, Projection:3-1/8”from Mounting Surface.
  • (Refer to our drawing for details) *UNSCREW THE BASE PLATE AND YOU WILL FIND YOUR INSTALLATION SCREW AND ANCHOR INSIDE..
  • RELIABLE QUALITY - HOMOTEK spring door stopper is made of metal, durable and available for longer service life than other door stoppers in market. We provide 2-year warranty, so just buy with confidence! If anything ever goes wr....
Check Stock

WELDANDFABSHOP 3/4" Adjustable Gate Hinges (Pair) Heavy Duty Pivot Hinge for Welding on Large Gates

  • ... Installation Distance Adjustable:There is a bolt that can be tightened and loosened based on your desires can be adjustable.The Gate Hinges are Adjustable from 0.23" - 1.25" Gap Between the Gate Post and Gate Frame.Please make sure there is at least 0.23" gap,So that it can be installed..
  • Easy to Install:The hinges can be installed without installation instructions.Please use the included 1" (2.5cm) self-tapping metal screws for installation on your vinyl fence.If using on a wooden fence,you will need wood screws (not included)..
  • Durable to Last:Gate Hinges made of high-strength galvanized steel,Black Surface treatment Powder Coating Increases  Gate Hinge Life.Whatever indoors or outdoors, in the sun or in the rain, it can be used for many years..
  • Customer Service:We have produce more than 30 years professional self closing gate hinges,We provide 24-hour online service, if you have any questions about the product or installation, please contact us. Enjoy Better DIY home improvement by choose us..
Check Stock

38mm Bolt-on 7/13/20 PSI External Turbo Exhaust Manifold Wastegate (Black)

  • ▶️ High strength cast steel body with steel head.
  • ▶️ Bolt-on design, fits any 38mm turbo manifold bolt-on wastegate port.
  • ▶️ Bolt-on housing design for secure spring changing and adjustment.
  • ▶️ High pressure reinforced and temperature resistant actuator diaphram included.
  • ▶️ Comes with 13 psi spring and 7 psi spring installed (2 springs installed for total 20 psi).
Check Stock

3 Piece Equalizer Rearview Mirror Adhesive Installer Tool & Kit, Spring Latch Rearview Mirror Removal Tool JMR357

  • ...ns. Unlike most brands, ours has a brush-on primer instead of spray. The adhesive has a gel-like consistency to keep it from running down the windshield..
  • To use it, clean the glass and mirror bracket thoroughly. Brush the primer on the glass where the bracket will be installed and then brush the primer on the mirror bracket. Let the primer dry then apply two drops of the adhesive to the bracket..
  • When you are ready to install the rearview mirror bracket, be careful to place it exactly where you want it. TIP: Most technicians mark on the outside of the glass to guide correct placement of the bracket since removal can be almost impossible after you have attached it. Be sure and wait 3-4 minutes before installing the rearview mirror back onto the bracket..
Check Stock

2 Pcs Boat Trailer Leaf Springs 25-1/4\ 25.25\ 4 Leaf 5000 lbs Capacity Per Pair

  • These 25 1/4" double eye leaf springs are rated at 2,500 lbs each for a total of 5,000 lbs. capacity per axle..
  • Double eye 4 Leaf Spring. 1 3/4" wide. 9/16" Inside Diameter nylon bushings included..
  • They are commonly seen with 5k or 6k lb. capacity axles..
  • They come with 9/16" bushings pre-installed, if you're replacing the springs on a boat trailer you will most likely need to switch those out to 1/2" bushings and hardware..
Check Stock

Camco EAZ LIFT Elite Weight Distribution Hitch, 1200lb Kit (48069)

  • Trailer Sway Control Kit: Save time with our weight distributing hitches that come in kits with mounting hardware and pre-installed components.
  • Pre-Installed Components: The pre-installed 2-5/16" hitch ball and sway control ball are torqued to specification on the adjustable ball mount hitch head.
  • U-bolts and chain package are pre-installed on the spring bars of the load-leveling hitch.
  • Maximum Weight Capacity: The weight distribution hitches with sway control have a maximum tongue weight capacity of 1,200 lbs and a maximum gross weight rating of 12,000 lbs.
  • Kit Includes: A weight distributing hitch, Eaz-Lift sway control hitch with mounting hardware, 2-5/16" ball, adjustable ball mount, installation instructions, and a 48120 Bolt Together 2" x 2" Hi-Low Shank of 12" length, 2.5" drop, and 5.5" rise.
  • Quality Products: Camco makes quality products for RVing, boating, camping, towing, tailgating, and grilling that help take your passion for the outdoors to the next level.
  • Includes 1,200 pound weight distributing hitch, sway control and 2-5/16" hitch ball.
  • Hitch ball and sway control ball are pre-installed and torqued to specification on adjustable ball mount.
  • U-bolts and chain package are pre-installed on spring bars.
  • 1,200 pound maximum tongue weight capacity....
Check Stock