Reviews Solid Carbide Reamers

Reed Tool PPR200 Clean Ream Extreme with 3/8-Inch Hex Shaft, 2-Inch Head

  • Reams 2-Inch Sch. 40 PVC, CPVC and ABS Fittings.
  • Can be used with standard drills, cordless drills, or impact drills.
  • Works great for vent lines, drain lines, water lines.
  • Feature a 4-sided carbide insert which provides an extra cutting edge after 180-Degree cutting insert rotation.
  • PPR Fitting Reamers are NOT recommended for use on pressurized systems.
Check Stock

Accusize Industrial Tools 2-24'' by 0.001'' Resolution Inside Micrometer Set, 3011-5051

  • The combining of extension rods provides a wide measuring range. Supplied with a standard caliper gauge for zero setting..
  • Carbide measuring faces. Diameter of extension rods: φ15.5mm. Rod Diameter: 0.61".
  • Accuracy: Metric(3+n+L/50)μm, (n=number of rod, L=maximum. Measuring length (mm) [Inch]. Resolution: 0.0001".
  • Each interchangeable rod is marked with its measuring range. Use to measure 3 flute cutting heads such as end mills, taps and reamers..
Check Stock

29/32\ Expansion Reamer, Carbide Tipped, Straight Shank, Partial Flute Carbide 56018P, USA Made

  • When the diameter wears down to the low limit, it may be expanded oversize, reground to size and recleared. The expansion screw should never be loosened in an attempt to use the reamer for a size smaller than that to which the tool was originally finish ground. These reamers are inteded to be used for 1 specific diameter, not multiple diameters..
  • 1 1/2 " flute length, Partial Flute Length Carbide.
  • 3/4 " shank diameter, For Reaming abrasive material.
  • This is an expansion reamer NOT an adjustable reamer. It can be expanded only and reground..
Check Stock

15/16\ Expansion Reamer, Carbide Tipped, Tapered Shank, Partial Flute Carbide 56069P, USA Made

  • When the diameter wears down to the low limit, it may be expanded oversize, reground to size and recleared. The expansion screw should never be loosened in an attempt to use the reamer for a size smaller than that to which the tool was originally finish ground. These reamers are inteded to be used for 1 specific diameter, not multiple diameters..
  • 1 1/2 " flute length, Partial Flute Length Carbide.
  • Morse taper shank #3, For Reaming Abrasive Material.
  • This is an expansion reamer NOT an adjustable reamer. It can be expanded only and reground..
Check Stock

29/32\ Expansion Reamer, Carbide Tipped, Tapered Shank, Partial Flute Carbide 56068P, USA Made

  • When the diameter wears down to the low limit, it may be expanded oversize, reground to size and recleared. The expansion screw should never be loosened in an attempt to use the reamer for a size smaller than that to which the tool was originally finish ground. These reamers are inteded to be used for 1 specific diameter, not multiple diameters..
  • 1 1/2 " flute length, Partial Flute Length Carbide.
  • Morse taper shank #2, For Reaming Abrasive Material.
  • This is an expansion reamer NOT an adjustable reamer. It can be expanded only and reground..
Check Stock

13/16\ Expansion Reamer, Carbide Tipped, Tapered Shank, Partial Flute Carbide 56065P, USA Made

  • When the diameter wears down to the low limit, it may be expanded oversize, reground to size and recleared. The expansion screw should never be loosened in an attempt to use the reamer for a size smaller than that to which the tool was originally finish ground. These reamers are inteded to be used for 1 specific diameter, not multiple diameters..
  • 1 3/8 " flute length, Partial Flute Length Carbide.
  • Morse taper shank #2, For Reaming Abrasive Material.
  • This is an expansion reamer NOT an adjustable reamer. It can be expanded only and reground..
Check Stock

1 3/16\ Expansion Reamer, Carbide Tipped, Straight Shank, Partial Flute Carbide 56026P, USA Made

  • When the diameter wears down to the low limit, it may be expanded oversize, reground to size and recleared. The expansion screw should never be loosened in an attempt to use the reamer for a size smaller than that to which the tool was originally finish ground. These reamers are inteded to be used for 1 specific diameter, not multiple diameters..
  • 1 3/4 " flute length, Partial Flute Length Carbide.
  • 1" shank diameter, For Reaming abrasive material.
  • This is an expansion reamer NOT an adjustable reamer. It can be expanded only and reground..
Check Stock

1 7/16\ Expansion Reamer, Carbide Tipped, Tapered Shank, Partial Flute Carbide 56080P, USA Made

  • When the diameter wears down to the low limit, it may be expanded oversize, reground to size and recleared. The expansion screw should never be loosened in an attempt to use the reamer for a size smaller than that to which the tool was originally finish ground. These reamers are inteded to be used for 1 specific diameter, not multiple diameters..
  • 2" flute length, Partial Flute Length Carbide.
  • Morse taper shank #4, For Reaming Abrasive Material.
  • This is an expansion reamer NOT an adjustable reamer. It can be expanded only and reground..
Check Stock

1 5/16\ Expansion Reamer, Carbide Tipped, Tapered Shank, Partial Flute Carbide 56078P, USA Made

  • When the diameter wears down to the low limit, it may be expanded oversize, reground to size and recleared. The expansion screw should never be loosened in an attempt to use the reamer for a size smaller than that to which the tool was originally finish ground. These reamers are inteded to be used for 1 specific diameter, not multiple diameters..
  • 1 7/8 " flute length, Partial Flute Length Carbide.
  • Morse taper shank #4, For Reaming Abrasive Material.
  • This is an expansion reamer NOT an adjustable reamer. It can be expanded only and reground..
Check Stock

F&D Tool Company 29321 Shell Reamer Carbide Tipped Spiral Flute, 2\ Diameter, 1\ Hole Diameter, 8\ Fits Arbor, 10 Number of Fits, 2 3/4\ Fit, 1 1/8\ Carb, 3 1/2\ Overall Length

  • Shell Reamers - Carbide Tipped - Spiral Flute.
  • Dia: 2 Hole Dia: 1 Fits Arbor: 8 Number of fits: 10 Fit: 2 3/4 Carb: 1 1/8 Overall: 3 1/2.
Check Stock

F&D Tool Company 29310 Shell Reamer Carbide Tipped Spiral Flute, 1 15/16\ Diameter, 3/4\ Hole Diameter, 7\ Fits Arbor, 8 Number of Fits, 2 1/4\ Fit, 1 1/8\ Carb, 3\ Overall Length

  • Shell Reamers - Carbide Tipped - Spiral Flute.
  • Dia: 1 15/16 Hole Dia: 3/4 Fits Arbor: 7 Number of fits: 8 Fit: 2 1/4 Carb: 1 1/8 Overall: 3.
Check Stock

F&D Tool Company 29312 Shell Reamer Carbide Tipped Spiral Flute, 1 7/16\ Diameter, 3/4\ Hole Diameter, 7\ Fits Arbor, 8 Number of Fits, 2 1/4\ Fit, 1 1/8\ Carb, 3\ Overall Length

  • Shell Reamers - Carbide Tipped - Spiral Flute.
  • Dia: 1 7/16 Hole Dia: 3/4 Fits Arbor: 7 Number of fits: 8 Fit: 2 1/4 Carb: 1 1/8 Overall: 3.
Check Stock

F&D Tool Company 29331 Shell Reamer Carbide Tipped Spiral Flute, 2 5/8\ Diameter, 1 1/2\ Hole Diameter, 10\ Fits Arbor, 14 Number of Fits, 3 1/8\ Fit, 1 1/8\ Carb, 4\ Overall Length

  • Shell Reamers - Carbide Tipped - Spiral Flute.
  • Dia: 2 5/8 Hole Dia: 1 1/2 Fits Arbor: 10 Number of fits: 14 Fit: 3 1/8 Carb: 1 1/8 Overall: 4.
Check Stock