Reviews Solder Liquid

10 Pieces No Clean Soldering Flux Pen and Solder Remover Wick, 0.1 Inch Wide and 59 Inch Long, Solder Braid Wick Liquid Solder Flux Pen for Electronics Welding Repair Tabbing Wire Maintenance

  • Nice combination: you will get 5 no clean soldering flux pens and 5 solder remover wick sets, 10 in total, sufficient quantity, thoughtful combination, to meet daily use and replacement needs.
  • Appropriate size: the no-clean solder wick is about 1.5 m/ 59 inches long and 2.5 mm/ 0.1 inches wide, and liquid flux brush flux pen is about 15 x 1.5 cm/ 6 x 0.6 inch, convenient to hold.
  • Please check the size carefully before purchasing.
  • Multiple reliable materials: these no-clean braided soldering wicks are made of quality copper wire, using nice weaving technology, which can enhance surface tension and absorb excess solder.
  • And flux remover pen adopts quality material, non-leakage, flux safe and prevents you from being exposed to organic solvents.
  • Practical tools: soft brush tip flux pen releases a moderate stream of liquid to clean components without spoiling the PCB copper foil or IC pins.
  • Solder remover has good thermal conductivity and absorption, helping to reduce the risk of thermal spoiling to the board.
  • Broad utilization: these flux pens and braided solder wicks can be applied in laboratories, computers, home repairs and to correct small PCB errors and through-hole joints, electronic soldering and much more, bringing a lot of convenience and effic....
Check Stock

Goss KA-725-M12P Welding and Brazing HVAC Torch Tool Kit with Stand for \MC\ Acetylene Tanks

  • ...r easy to ignite the flame. Brass constructed threading regulator assure durability and reliability, pressure regulated for consistent performance even when tiled or momentarily inverted. adjustable flame control knob can easily sized flame for different applications.
  • Added 15% Silver into Phos-Copper brazing rods.A solder rod with 15% silver added can be liquid phase temperature down to 1472°F. The temperature at which it melts from a solid to a liquid is 1472°F..
  • Each 0.5 lb tube contains 19 sticks of 14" brazing rods. Significantly lower melting point:A solder rod with 15% silver added can be liquid phase temperature down to 1472°F. The melting temperature from solid to liquid is 1472°F..
  • Enhanced metallicity: The addition of silver will improve the metallic plasticity, increase the strength and strengthen the toughness of the metal in the welded joint. Wettability: The addition of silver will improve the wettability of the welded joint, thus allowing perfect filling of every gap..
Check Stock

Delcast Rosin Soldering Flux Paste 50G

  • The benefit of liquid flux is that its transparency will let you see the solder joint more clearly when soldering and the liquid flows better in joints than a paste.
  • Use this hard flux on Gold, Silver, Platinum, and other metals with high melting point.
  • Yellow-green and self-pickling, it is the best in water-based fluxes.
Check Stock

Aquiflux Self Pickling Flux for Precious Metals Gold Silver Jewelry and Hard Soldering 8 Oz Half Pint

  • Includes: one half-pint (8 fluid ounces within a spray bottle).
  • Yellow-green and self-pickling, it is the best in water-based fluxes.
  • Use this hard flux on Gold, Silver, Platinum, and other metals with high melting point.
  • The benefit of liquid flux is that its transparency will let you see the solder joint more clearly when soldering and the liquid flows better in....
Check Stock

Mastercraft 60/40 Solder - 1 Lb.

  • 60/40 blend stays in a liquid stage longer, giving you more time to produce smooth solder seams.
  • 60/40 flows readily, has a small pasty phase, looks great.
Check Stock

Forney 60300 Solder Flux Brush, 3-Pack

  • Also used for solder and other applications.
Check Stock

MOGAOPI Solder Wick and Desoldering Pump, Spare nozzle, Solder Sucker & Desoldering Wick,1pcs Solder Braid Desoldering Vacuum Pump Solder Remover Tool

  • ( 4-in-1 Solder Removal Tool ) 1pcs desoldering vacuum pumps ,1pcs Spare nozzle ,1pcs solder wicks and 1pcs High Temperature Resistance Silicone Protective Tube(15cm Length), a must-have tool for electronics kit, the desoldering wick absorbs solder, the desoldering pump pulls it away quick, while the solder wick is better for small amounts of solder, the solder sucker takes up large amounts..
  • ( One-handed solder sucker with powerful suction ) you can using the desoldering pump by just cocking it and pressing the trigger button with one hand when you are ready, the desoldering pump designed with double ring double open and "vacuum" button, which make the sucking power awesome..
  • ( Desoldering Wick with copper braid ) 1pcs solder braid with the size 2.5mm Width, 1.5m Length, this desoldering wick has geometrically-precise weave with copper and rosin, work from the tip of the desoldering wick, once the desoldering wick and the solder has been heated, the solder braid can quickly absorbed molten solder and left a clean working area..
  • ( ABS body with non-slip sponge and Nylon nozzle desoldering pump ) The body of the desoldering vacuum pump is made of high quality ABS, which make the solder sucker delicate and durable, also the covered sponge can absorb sweat....
Check Stock

Tabiger Solder Wick & Desoldering Pump, Solder Sucker & Desoldering Wick, 2pcs Solder Braid (2.5mm Width, 1.5m Length)- Desoldering Vacuum Pump Solder Remover

  • 【One-handed solder sucker with powerful suction 】 Whether you are right or left-handed, you can using the desoldering pump by just cocking it and pressing the trigger button with one hand when you are ready, the desoldering pump designed with double ring double open and "vacuum" button, which make the sucking power awesome..
  • 【Desoldering Wick with copper braid】 2pcs solder braid with the size 2.5mm Width, 1.5m Length, this desoldering wick has geometrically-precise weave with copper and rosin, work from the tip of the desoldering wick, once the desoldering wick and the solder has been heated, the solder braid can quickly absorbed molten solder and left a clean working area..
  • 【ABS body with non-slip sponge and Nylon nozzle desoldering pump】 The body of the desoldering vacuum pump is made of high quality ABS, which make the solder sucker delicate and durable, also the covered sponge can absorb sweat and heat, make it comfortable to hold, the nylon nozzle of the solder suck can endure high temperature, thus it can be used for a long time..
  • 【3-in-1 Solder Removal Tool】 1pcs desoldering vacuum pumps and 2pcs solder wicks, a must-have tool for electronics kit, the desoldering wick absorbs solder, the desoldering pump pulls it away quick, while....
Check Stock

Mogaopi Desoldering Wick, Desoldering Pump, Solder Sucker, Solder Wick, 2pcs Solder Braid (2.5mm Width, 1.5m Length) Solder Wire, Replacement Tip, Desoldering Vacuum Pump Solder Removal Tool

  • 【6-in-1 Solder Removal Tool】: 2 pcs Desoldering Wire, 1pcs Solder Wire, 1pcs Desoldering Pump, 1pcs Replacement Tip, 1pcs Protective Tube(15cm Length), a must-have tool for electronics kit, the desoldering wick absorbs solder, the desoldering pump pulls it away quick, while the solder wick is better for small amounts of solder, the solder sucker takes up large amounts..
  • Desoldering Wick with Copper Braid - Solder wire, replacement tip, 2pcs solder braid (3.5mm/2.0mm Width, 1.5m Length). 100% copper wick has fine braid design to promote strong capillary action to pull in excess solder..
  • 【One-handed solder sucker with powerful suction】: Whether you are right or left-handed, you can using the desoldering pump by just cocking it and pressing the trigger button with one hand when you are ready, the desoldering pump designed with double ring double open and "vacuum" button, which make the sucking power awesome..
  • ABS Body with Non-slip Sponge and Nylon Nozzle Solder Wick - The body of the desoldering vacuum pump is made of high quality ABS, which make the solder sucker delicate and durable, also the covered sponge can absorb sweat and heat, make it comfortable to hold. Right or Left handed design allows easy one-handed use..
Check Stock

Teenitor Solder Sucker Desoldering Vacuum Pump Solder Removal Tool 3pcs/Pack Desoldering Pump Soldering Sucker Tool

  • UNPARALLELED SUCTION POWER - Good little solder sucker, have a good bit of suction,you can just hang onto it and use your thumb to reset and suck. The ideal tool for intricate soldering jobs..
  • ONE-HANDED OPERATION - Simple design allows easy one-handed use,lightweight and compact,suck the solder away easily. Say goodbye to tedious two-handed solder extraction and .quickly and easily removing solder.
  • DURABILITY AND LONGEVITY - Very sturdy,will worke good to remove existing solder from a circuit board. Made with high-quality materials and designed to withstand heavy usage, our Solder Sucker ensures longevity and performance, saving you time and money in the long run..
  • ERGONOMIC DESIGN - Heated up the solder pushed the button and bam,all solder sucked up,super easy to use for desoldering. The comfortable, non-slip handle and lightweight body make our Solder Sucker easy to handle, ensuring maximum control and precision..
  • VERSATILE APPLICATIONS - A must have excellent solder sucker which fits nicely in your tool box. Our solder sucker desoldering pump is not just limited to soldering. It can also be used for desoldering, removing hair, lint, and dust, and even for cleaning delicate electronics. The ultimate multi-purpose tool for any DIY enthusiast..
Check Stock

3 Pcs Solder Sucker Desoldering Vacuum Pump Solder Removal Tool

  • 【High Quality and Powerful Sunction】The solder sucker has an aluminum bronze frame and a high pressure vacuum which can remove solder from a printed circuit board effectively and you can use your thumb to reset and suck..
  • 【One-Handed Use Design】 The Solder sucker with simple construction, so whether you are right or left-handed, you can using the desoldering pump by just cocking it and pressing the trigger button with one hand when you are ready..
  • 【 Sturdy and Perfect Tool】Worke good to remove existing solder from a circuit board, heated up the solder pushed the button and bam,all solder sucked up,super easy to use for desoldering..
  • 【Great Solder Removal Tool】 The solder sucker can be used for broad place, a must have excellent solder sucker which fits nicely in your tool box..
  • 【Lifetime Satisfaction Guarantee】If you're not happy we're not happy! If we can't make it right and you are not satisfied for any reason, we will gladly and promptly refund your purchase price. We promise! Click "Add to Cart" now..
Check Stock

yzc Rosin core solder-Solder wire 63-37 Solder flux, Electronic solder, diameter 1MM, net weight 20G, portable storage tube, suitable for electronics, circuit boards, ICs, etc. DIY(Rosin core solder)

  • 【rosin core solder wire:】Solder flux solder wire with special formula of high-quality tin ingots from Yunnan, China and high-quality rosin..
  • 【Tin wire parameters:】 rosin solder wire Tin 63%- Lead 37% (Sn63-Pb37)..
  • 【Soldering wire specifications:】rosin flux content 1.8%, rosin solder wire 1.0mm (0.0394inch), 20 gm (0.044lbs), gross weight 28 gm (0.0617lbs),Tin pen is suitable for carrying in a pocket..
  • 【Low melting point:】 361F/183C. Easy to solder, smooth flow, fast soldering speed and firm solder joints..
  • 【Electronic solder Application:】Rosin core solder wire for-solder for electronics Have Very good soldering ability, especially the repair of electrical equipment such as circuit boards,electronics，IC, home improvement, cable TV, radio/sterro,toys etc DIY..
Check Stock

5 Pieces No Clean Solder Flux Pen 5.6 Inch Length for Electronics Tabbing Wire Soldering Welding Repair

  • What can you get: the package includes 5 pieces of no clean solder flux pens, enough quantity providing you a wide choice for daily life use and replace.
  • Proper size: the soldering no clean flux pen measure approx. 14.3 cm/ 5.6 inches in length, please check the size carefully before purchasing.
  • Reliable and quality material: the liquid soldering pen is made of reliable materials and no leak and safe design for protecting the flux, keep you from touching the organic solvents.
  • Wide applications: these flux pens can be applied for laboratory, computer, telecommunications, home repairs, bringing a lot of convenience to your work.
  • Simple operation: you only need to press the pen tip 1-2 times to release the liquid, and after use, the flux pen can be cleaned with alcohol.
Check Stock