Martin 2517 1 1/2 Taper Bushing, Sintered Steel, Inch, 1.5\ Bore, 3.375\ OD, 1.75\ Length
- Taper bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
- Flush-mounted bushing with a split taper for reduced mounting width and a tight clamp to shafts.
- Sintered steel for greater strength and resistance to wear than steel.
- Keyed to the shaft to prevent the shaft from rotating in the bushing.
- Interchangeable with taper bushings from various manufacturers.
Check StockMartin 1008 5/8 Taper Bushing, Sintered Steel, Inch, 0.62\ Bore, 1.386\ OD, 0.875\ Length
- Taper bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
- Flush-mounted bushing with a split taper for reduced mounting width and a tight clamp to shafts.
- Sintered steel for greater strength and resistance to wear than steel.
- Keyed to the shaft to prevent the shaft from rotating in the bushing.
- Interchangeable with taper bushings from various manufacturers.
Check StockMartin 2517 2 7/16 Taper Bushing, Sintered Steel, Inch, 2.44\ Bore, 3.375\ OD, 1.75\ Length
- Taper bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
- Flush-mounted bushing with a split taper for reduced mounting width and a tight clamp to shafts.
- Sintered steel for greater strength and resistance to wear than steel.
- Keyed to the shaft to prevent the shaft from rotating in the bushing.
- Interchangeable with taper bushings from various manufacturers.
Check StockMartin 2517 1 1/4 Taper Bushing, Sintered Steel, Inch, 1.25\ Bore, 3.375\ OD, 1.75\ Length
- Taper bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
- Flush-mounted bushing with a split taper for reduced mounting width and a tight clamp to shafts.
- Sintered steel for greater strength and resistance to wear than steel.
- Keyed to the shaft to prevent the shaft from rotating in the bushing.
- Interchangeable with taper bushings from various manufacturers.
Check StockMartin 2012 1 5/8 Taper Bushing, Sintered Steel, Inch, 1.63\ Bore, 2.75\ OD, 1.25\ Length
- Taper bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
- Flush-mounted bushing with a split taper for reduced mounting width and a tight clamp to shafts.
- Sintered steel for greater strength and resistance to wear than steel.
- Keyed to the shaft to prevent the shaft from rotating in the bushing.
- Interchangeable with taper bushings from various manufacturers.
Check StockMartin 2012 1 1/8 Taper Bushing, Sintered Steel, Inch, 1.13\ Bore, 2.75\ OD, 1.25\ Length
- Taper bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
- Flush-mounted bushing with a split taper for reduced mounting width and a tight clamp to shafts.
- Sintered steel for greater strength and resistance to wear than steel.
- Keyed to the shaft to prevent the shaft from rotating in the bushing.
- Interchangeable with taper bushings from various manufacturers.
Check StockMartin SH 1 Quick Disconnect Bushing, Sintered Steel, Inch, 1\ Bore, 1.871\ OD, 1.31\ Length
- Quick disconnect bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
- Split through flange and taper to provide strong clamping on the shaft.
- Sintered steel for greater strength and resistance to wear than steel.
- Keyed to the shaft to prevent the shaft from rotating in the bushing.
- Set screw over keyway to help keep key in place on vertical shafts and with vibrating loads.
Check StockMartin JA 1 Quick Disconnect Bushing, Sintered Steel, Inch, 1\ Bore, 1.375\ OD, 1.06\ Length
- Quick disconnect bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
- Split through flange and taper to provide strong clamping on the shaft.
- Sintered steel for greater strength and resistance to wear than steel.
- Keyed to the shaft to prevent the shaft from rotating in the bushing.
- Set screw over keyway to help keep key in place on vertical shafts and with vibrating loads.
Check StockMartin JA 7/16 Quick Disconnect Bushing, Sintered Steel, Inch, 0.43\ Bore, 1.375\ OD, 1.06\ Length
- Quick disconnect bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
- Split through flange and taper to provide strong clamping on the shaft.
- Sintered steel for greater strength and resistance to wear than steel.
- Keyed to the shaft to prevent the shaft from rotating in the bushing.
- Set screw over keyway to help keep key in place on vertical shafts and with vibrating loads.
Check StockMartin SK 7/8 Quick Disconnect Bushing, Sintered Steel, Inch, 0.87\ Bore, 2.812\ OD, 1.93\ Length
- Quick disconnect bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
- Split through flange and taper to provide strong clamping on the shaft.
- Sintered steel for greater strength and resistance to wear than steel.
- Keyed to the shaft to prevent the shaft from rotating in the bushing.
- Set screw over keyway to help keep key in place on vertical shafts and with vibrating loads.
Check StockMartin SDS 1 1/8 Quick Disconnect Bushing, Sintered Steel, Inch, 1.13\ Bore, 2.187\ OD, 1.37\ Length
- Quick disconnect bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
- Split through flange and taper to provide strong clamping on the shaft.
- Sintered steel for greater strength and resistance to wear than steel.
- Keyed to the shaft to prevent the shaft from rotating in the bushing.
- Set screw over keyway to help keep key in place on vertical shafts and with vibrating loads.
Check StockMartin SF 1 7/16 Quick Disconnect Bushing, Sintered Steel, Inch, 1.44\ Bore, 3.125\ OD, 2.06\ Length
- Quick disconnect bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
- Split through flange and taper to provide strong clamping on the shaft.
- Sintered steel for greater strength and resistance to wear than steel.
- Keyed to the shaft to prevent the shaft from rotating in the bushing.
- Set screw over keyway to help keep key in place on vertical shafts and with vibrating loads.
Check StockMartin SH 32MM Quick Disconnect Bushing, Sintered Steel, Metric, 32 mm Bore, 47.52 mm OD, 33.33 mm Length
- Quick disconnect bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
- Split through flange and taper to provide strong clamping on the shaft.
- Sintered steel for greater strength and resistance to wear than steel.
- Keyed to the shaft to prevent the shaft from rotating in the bushing.
- Set screw over keyway to help keep key in place on vertical shafts and with vibrating loads.
Check Stock