Reviews Signal Input Module

Agatige Frequency to Voltage Converter Module, 0-10Khz to 0-10V F/V Digital to Analog Converter Conversion Module

  • FUNCTION: The frequency of the pulse signal 0HZ to 10KHZ converts into an analog voltage signal of 0-10V. Can be used to interface switching between the PLC and the frequency converter, or interface matching such as the matching of motion control card and inverter control..
  • FEATURES: Input pulse level is 5V 12V 24V, which can be directly entered without serial resistor. The input signal frequency must maintain more than 0.5 seconds..
  • ANTI-INTERFERENCE: Conversion module's signal inputs with optical coupling isolation, which can ensure that the capability of anti-interfence..
  • APPLICATION: Frequency to Voltage Converter Module Can be used for industrial control panel PLC or other signal interface switching.
  • MAJOR SPECIFICATIONS: Output current: 5MA,Voltage: 0-10V, Input pulse level: 5V 12V 24V, Frequency: 0 to 10KHZ..
Check Stock

Level Translator 5V/24V, 8 Channel NPN/PNP to NPN Level Conversion Module, Level Conversion Board, Voltage Level Converter Board 10MHZ

  • 【Convert Input Level Signal】The module can convert input 5V level signal to 24V level signal, or convert input 24V level signal to 5V level signal..
  • 【 Anti-interference】It can also convert signal 5V to 5V, or 24V to 24V level, and isolate input signal and output signal through optocoupler, which can improves anti-interference ability of circuit..
  • 【Set by Dip Switch】Input level can be set by DIP switch, 24V level output is NPN OC output, output current is 100mA..
  • 【Strong Driving Ability】It has conversion and amplification circuit, good wave, strong driving ability..
  • 【PLC Interface Standards】Compatible with a common-cathode or common-anode input connection, matching European and Japanese PLC interface st Plc Interface Standardsandards..
Check Stock

PC Interface Controller

  • 【One-year after-sale warranty】The PWM to voltage module converts PWM digital signals to 0 to 10V analog signals. It can be used to switch the signal interface of PLC or other industrial control board. Adjust the output voltage by adjusting the PWM duty cycle. The module is small in size and easy to apply in different places.003cbr003e.
  • Using MCU embedded technology. Easy to operate, can be fine-tuned by potentiometer.003cbr003e.
  • Select the PWM signal input level range by short circuit. The module is small, easy to carry and easy to use.003cbr003e.
  • (current greater than 100mA)，PWM signal receiving frequency range: 1KHZ-3KHZ.
  • When power on for the first time, it is best to do a calibration and debugging: find a signal with a 50% duty cycle and connect it to PWM and GND. Jumper caps set the corresponding voltage range. When the frequency is 1KHZ-3KHZ, use a multimeter to measure the two ports of VOUT and GND. At this time, the meter displays about 5V. Adjust the potentiometer on the board so that the multimeter displays 5.00v.003cbr003e.
Check Stock

Analog Voltage to PWM Signal Converter, 0-5V/0-10V Analog Input Voltage to 0-100% PWM Signal 2KHZ-20KHZ Converter Module,for PWM Motor Speed Control Interface Circuit Activity

  • Voltage to PWM Signal Converter Module: This module can convert 0-5V or 0-10V analog input voltage into 0-100% PWM signal..
  • Wide Application: This module is widely used for PWM motor speed control interface circuit, instrumentation AD interface conversion, and other applications that need convert voltage to PWM signal..
  • PWM Signal Frequency Range: The PWM signal frequency range is 2KHZ-20KHZ, maximum is 20KHZ, default minimum is 2KHZ,Hyuduo is committed to providing customers with high-quality products and thoughtful service..
  • Setable Output Frequency: The default function of this module is converting 0-10V into 0-100% 2KHZ PWM signal, but the output frequency can be set by adjusting potentiometer as needed,stable and reliable performance, practical, easy to operate and use, has a long service life..
  • Two Kinds of PWM Signal: There are two kinds of PWM signal, PNP-PWM output and NPN-PWM output. The PNP-PWM output is only 5V level, NPN-PWM output is 5V and 24V level,If you have any problem,please contact us, we will strive to provide you with satisfactory service!.
Check Stock

16mA Logarithmic Amplifier Module 100 DB Amplifier Board 5MHZ‑500MHZ SMA Detector Module for FSK PSK Demodulation Signal Reception

  • Logarithmic Amplifier Module: Logarithmic output of the logarithmic amplifier module is proportional to the logarithm of the input signal..
  • RSSI Linearity: ±0.4 dB RSSI linearity, RSSI scale does not change with temperature and feed voltage..
  • Apply to: Used for received signal strength indicator (RSSI) and phase detection in cellular base stations, radar and other radio transceiver applications..
  • Specific Parameters: 16mA current, 20 mV/dB slope, ‑95 dBm intercede, SMA female, 5MHZ‑500MHZ frequency range, 100 dB gain. Dynamic Range: 100 dB -78 dBm to +22 dBm (Re 50 O). Total Gain: 100 dB. Bandwidth: 500 MHz. Sleep Current: 003c1mA..
  • Founction: AD8309 amplifier module, with limiting output, can be used as FSK PSK demodulation. Input and Output Interface: SMA Female..
Check Stock

Isolation Amplifiers Isolated Modulator (5 pieces)

  • ➤【DC12-32V】- This isolation module need two complete independent DC12-32V power supply..
  • ➤【Main function】- Main function is input 0-10V analog voltage signal,after isolation, output 0-10V analog voltage signal..
  • ➤【Scope of Application】- Used to isolate high voltage or strong interference voltage or current (voltage) signal then transferred to PLC or controller MCU, isolating controlling end and controlled end, to assure stability and anti-interference ability of system..
  • ➤【Use】- It will has better performance if install this module and controller in a metal box and box is grounded..
  • ➤【Note】- The potentiometer is used to amend corresponding relation of output voltage. Output voltage can be fine adjusted and calibrated, normally it has already been calibrated..
Check Stock

High Speed Comparator High Speed Frequency Meter Front Shaping Comparator for Low-Voltage Applications Conversion Circuit

  • LOW VOLTAGE APPLICATIONS -- The input common mode range is better than the swing input, which is very suitable for low voltage applications..
  • APPLICATION -- Digital module can be used for wide voltage range and periodic signal shaping..
  • FRONT END ADJUSTMENT -- Used as a front end conditioning module in time domain measurements for frequency and phase difference..
  • PARAMETER -- The input voltage is 10 to 1000mV, the input frequency is about 200MHz DC, and the input impedance is 50 ohms..
  • RAIL TO RAIL OUTPUT -- The output level mode is rail to rail output, which can directly drive TTL / CMOS level..
Check Stock

Logarithmic Amplifier Module ±0.4 DB RSSI Linearity with Limiting Output Can Be Used As FSK PSK Demodulation

  • AD8309 AMPLIFIER MODULE - AD8309 amplifier module, with limiting output, can be used as FSK PSK demodulation..
  • APPLICATION - Used for received signal strength indicator (RSSI) and phase detection in cellular base stations, radar and other radio transceiver applications..
  • 16mA current, 20 mV/dB slope, ‑95 dBm intercede, SMA female, 5MHZ‑500MHZ frequency range, 100 dB gain..
  • ±0.4 DB RSSI LINEARITY - ±0.4 dB RSSI linearity, RSSI scale does not change with temperature and feed voltage..
  • Logarithmic output of the logarithmic amplifier module is proportional to the logarithm of the input signal..
Check Stock

Logarithmic Amplifier Module ±0.4 DB RSSI Linearity ‑95 DBM Intercede, Sma Female Can Be Used As FSK PSK Demodulation

  • 16mA current, 20 mV/dB slope, ‑95 dBm intercede, SMA female, 5MHZ‑500MHZ frequency range, 100 dB gain..
  • APPLICATION - Used for received signal strength indicator (RSSI) and phase detection in cellular base stations, radar and other radio transceiver applications..
  • Logarithmic output of the logarithmic amplifier module is proportional to the logarithm of the input signal..
  • ±0.4 DB RSSI LINEARITY - ±0.4 dB RSSI linearity, RSSI scale does not change with temperature and feed voltage..
  • AD8309 AMPLIFIER MODULE - AD8309 amplifier module, with limiting output, can be used as FSK PSK demodulation..
Check Stock

Geekworm Raspberry Pi Hdmi in Module, Hdmi to CSI-2 C790, Hdmi Input TC358743 Supports up to 1080p60fps Video & Audio Supported Compatible with Raspberry Pi 4B/3B+/3B/Pi Zero/W/2W/CM4

  • 【Overview】This C790 Hdmi to CSI module takes the incoming HDMI signal and converts it into a separate CSI signal&I2S audio signal. ( Raspberry Pi 4 and Pi ZeRo only support 2 lan, max 1080P@50fps, and CM4 can support 4 lan, max 1080P@60fps).
  • 【Compatibility】Compatible with Raspberry Pi 4 Model B, Raspberry Pi 3 Model B+/3B, Raspberry Pi 3 Model A+, Raspberry Pi 2 Model B,Raspberry Pi 1 Model B+, Raspberry Pi Zero/Zero W/Zero 2W, Raspberry Pi CM4/CM3 with IO board..
  • HDMI Input: supports up to 1080P60Hz on Raspberry Pi.
  • 【Packing List】: ✔1 x HDMI to CSI-2 Module C790 ✔1 x FPC 15pin 1.0mm cable（15cm length） ✔1 x FPC 22pin 0.5mm cable（15cm length） ✔1 x I2S cable (15cm length).
  • 【User manual】Refer to our WiKi search C790..
Check Stock

Premium 3 in 1 Out RCA Switch Box, Passive Stereo Signal Source selector, Audio switcher Splitter Box (Black)

  • This compact RCA switcher box allows connection of up to 3 stereo sources input and selects one audio output through the rotary knob(Note: When 1-in 3-out, 3 outputs are not simultaneously).
  • Audio input stereo signal switch, for multiple sources signal select, No signal loss.
  • Specialized audio rotary switch, Golden plated RCA.
  • Durable Solid aluminum case, Solid aluminum knob.
Check Stock

Large Current 50A H-Bridge High-Power Single-Channel Motor Driver Module Semiconductor Refrigeration

  • 【H-bridge Driver Module】The drive uses a full H-bridge driver module full-bridge MOSFET driver chip and composed with very low internal resistance and high current. MOSFET H-bridge driver circuit, with strong drive and braking effect, signal isolation chip isolates motor drive effectively..
  • 【Effective Protection】With the microcontroller PWM signal isolation, effectively protect microcontroller..
  • 【Input Maximum】To achieve the motor forward and reverse rotation, two PWM input maximum 200kHz frequency..
  • 【Fully Compatible】Power indicator is schematically clear. The power supply voltage 5V to 15V. 3.3V to 12V, PWM level is fully compatible. High current 50A..
  • 【Warm Tips】Ffor your safety and protection of use, our product is tested to ensure trouble-free installation and performance, please rest assured to buy..
Check Stock

DORHEA 5PCS TM1637 0.56\ 4 Bits Digital LED Display Module with Clock Display 0.36 inch Common Anode Red Digital Tube Board with Cable for Arduino Raspberry Pi DIY Kits

  • The module is a 12 foot with a clock point four common anode tube (0.36 in.) display module driver IC is TM1637 driver IC TM1637, only two signal lines can make the MCU control 4 8 digital tube..
  • Display device is a total of 4 red LED word tube. Digital tube 8 grayscale adjustable. Control interface level can be 5V or 3.3V..
  • 4-digit LED display module with LED brightness adjustable and clock point, can be used to display decimal, letters and so on, suitable for uses in induction cooker, micro-wave oven and small household electrical appliance..
  • Total 4 pins (GND, VCC, DIO, CLK), GND to ground, VCC for the power supply, DIO for the data input and output pins, CLK for the clock signal pin..
  • The Positioning holes in this LED Display Module 4 Bits has 4 M2 screws positioning hole diameter is 2.2mm and the positioning of the module is easy to install with easy to achieve the inter-module combination..
Check Stock