Reviews Signal Analyzer

Portable TinySA Spectrum Analyzer, SEESII Upgraded V0.3.1 Tiny Frequency Analyzer with Antenna SMA Male to UHF Female Cables, 100kHz to 960MHz MF/HF/VHF UHF Input, 2.8'' Touchscreen Signal Generator

  • 【Frequency Range 】Tiny Spectrum Analyzer with two inputs, high quality MF/HF/VHF input for 0.1MHZ-350MHz, lesser quality UHF input for 240MHz-960MHz. Switchable resolution bandpass filters for both ranges between 2.6kHz and 640kHz. Color display showing 290 scan points covering up to the full low or high frequency rangefrequency range. The tinySA contains all the components of a conventional heterodyne swept spectrum analyzer..
  • 【Built-in Calibration Signal Generator】When not used as Spectrum Analyzer it can be used as Signal Generator, MF/HF/VHF sinus output between 0.1MHZ-350MHz, UHF square wave output between 240MHz-960MHz. Built-in calibration signal generator that is used for automatic self test and low input calibration..
  • 【Tiny Spectrum analyzers】Switchable resolution bandpass filters for both ranges between 2.6kHz and 640kHz.Color display showing 290 scan points covering up to the full low or high frequency range. Bulit-in rechargeable battery allowing a minimum of at least 2 hours portable use..
  • 【PC Control】Connected to a PC via USB it becomes a PC controlled Spectrum Analyzer.The USB interface implements the Serial over USB (CDC) protocol and there is a large set of commands that can be invoked over the serial interface. These co....
Check Stock

Portable TinySA Spectrum Analyzer,SEESII Upgraded V0.3.1 Handheld Tiny Frequency Analyzer 100kHz to 960MHz MF/HF/VHF UHF Input,Signal Generator with 2.8 inch Touch Screen with ESD Protect Function

  • 【Frequency Range 】Tiny Spectrum Analyzer with two inputs, high quality MF/HF/VHF input for 0.1MHZ-350MHz, lesser quality UHF input for 240MHz-960MHz. Switchable resolution bandpass filters for both ranges between 2.6kHz and 640kHz. Color display showing 290 scan points covering up to the full low or high frequency rangefrequency range. The tinySA contains all the components of a conventional heterodyne swept spectrum analyzer..
  • 【Built-in Calibration Signal Generator】When not used as Spectrum Analyzer it can be used as Signal Generator, MF/HF/VHF sinus output between 0.1MHZ-350MHz, UHF square wave output between 240MHz-960MHz. Built-in calibration signal generator that is used for automatic self test and low input calibration..
  • 【Tiny Spectrum analyzers & ESD Function】Switchable resolution bandpass filters for both ranges between 2.6kHz and 640kHz.Color display showing 290 scan points covering up to the full low or high frequency range. Bulit-in rechargeable battery allowing a minimum of at least 2 hours portable use.The performance of the 2021 latest version 3.1 will be more stable and sensitive, with a new ESD protrcted function enable the product to have a higher antistatic level and a longer service life..
Check Stock

Portable tinySA Spectrum Analyzer - AURSINC Handheld Frequency Analyzer V0.3.1 with Antenna SMA Male to UHF Female Cables & 30db Attenuator MF | HF | VHF UHF Input for 0.1MHZ-960MHz 2.8'' Touchscreen

  • [2022 Upgraded Version: ESD Protection Diodes] Produced by Hugen, portable spectrum analyzer with latest firmware V0.3.1, the displayed version info is "ESD protected" meaning the diodes are installed which will be more stable and sensitive with higher antistatic level and longer service life. NOTE: Due to the old inventory might mix with the new batch, and If you got the old version Tiny spectrum analyzer and want a new one, you could apply a replacement for it..
  • [Frequency Range] Spectrum analyzers like the Tiny spectrum analyzer use a resolution filter that is used to isolate the input power in a small frequency range. This resolution filter is swept across the desired frequency range. The fastest scanning speed occurs with an RBW or 300kHz or wider and is about 2 scans per second. But with increase of the frequency span and decrease of the RBW the scanning speed decreases quickly. A scan from 0MHz to 350MHz with an RBW of 10kHz takes about 2 minutes..
  • [2 in 1 Device] When not used as Spectrum Analyzer it can be used as Signal Generator, MF/HF/VHF sinus output between 0.1MHZ-350MHz, UHF square wave output between 240MHz-960MHz. Built-in calibration signal generator that is used for automatic self test and low input calibration. The Tiny spectru....
Check Stock

Spectrum Analyzer USB 35-4400M Signal Source RF Frequency Domain Black Analysis Tool with Tracking Source Module Industrial Supplies

  • RF Frequency Domain Analysis Tool. Sweep Bandwidth: 33mHz---4400mHz.
  • Turn on the tracking source output bandwidth 33mhz---3000mhz.
  • Made of fine quality material, the Spectrum Analyzer has a long service life. Small and portable, high accuracy.
  • Signal Source Spectrum Analyzer. Software used on the computer side: NWT4.11.09 version.
  • Computer operating system: Winxp, Win7, Win10.
  • 35-4400M Signal Tracking Source Module is an RF frequency domain analysis tool.
  • Signal Tracking Source Module with Shell. Sweep Step: ≥33-68.75mHz/125Hz, 68.75-137.5mHz/250Hz, 137.5-275mHz/500Hz, 275-550mHz/1kHz,....
Check Stock

Upgraded TinySA Spectrum Analyzer,Karagas Spectrum Analyzer Handheld,MF/HF/VHF Input for 0.1MHZ-350MHZ and UHF Input for 240MHZ-960MHZ,Portable Frequency Analyzer with 2.8 Inch Touch Screen V0.3.1

  • 003cp003e◙【003cb003eBuilt-in 2-in-1 Calibration Signal Generator003c/b003e】This TinySA Spectrum Analyzer built-in calibration signal generator that is used for automatic self test and low input calibration.When not doing spectrum analyzer,it can be used as signal generator with two frequency outputs,MF/HF/VHF sinus output for 0.1MHZ-350MHz and UHF square wave output for 240MHz-960MHz.003c/p003e.
  • 003cp003e◙【003cb003e Frequency Range003c/b003e】The 2.8-inch color touch screen displays 290 scanning points,covering the entire range of low-frequency or high-frequency ranging frequencies.0.1 MHz -350 MHz high quality IF/HF/VHF input,240 MHz -960 MHz low quality UHF input.A switchable resolution band-pass filter suitable for the range from 2.6 kHz to 640 kHz.003c/p003e.
  • 003cp003e◙【003cb003ePC Control003c/b003e】This spectrum analyzer can be connected to PC through USB and realizes the serial over USB (CDC) protocol,which can call a large number of commands.The Windows driver will be automatically installed after connecting to the Windows computer.The Linux driver is built into the kernel.003c/p003e.
  • 003cp003e◙【003cb003ePortable Spectrum Analyzer & ESD Protection Function003c/b003e】The latest version 3.1, new ESD protection function, insta....
Check Stock

TinySA Spectrum Analyzer,Handheld Tiny Spectrum Analyzer TinySA 2.8inch Touch Screen,Portable Frequency Analyzer 0.1MHz~ 960MHz MF/HF/VHF UHF Input, Signal Generator with Battery

  • 【Input Frequency Range】Spectrum Analyzer with two inputs, high quality MF/HF/VHF input for 0.1MHZ-350MHz, lesser quality UHF input for 240MHz-960MHz..
  • 【2-in-1】Built-in calibration signal generator that is used for automatic self test and low input calibration.When not used as Spectrum Analyzer it can be used as Signal Generator, MF/HF/VHF sinus output between 0.1MHZ-350MHz, UHF square wave output between 240MHz-960MHz..
  • 【2.8inch Touching Display Screen】Switchable resolution bandpass filters for both ranges between 2.6kHz and 640kHz.Display resolution 320*240 pixels.Color display showing 290 scan points covering up to the full low or high frequency range.Scanning speed of over 1000 points/second using largest resolution filters..
  • 【PC Controlled 】Connected to a PC via USB it becomes a PC controlled Spectrum Analyzer.Bulit-in rechargeable battery allowing a minimum of at least 2 hours portable use.*Resistive touch contro*Jog switch control*USB serial port control.
  • 【Package List】1x Tiny Spectrum Analyzer.
Check Stock

InnoMaker Mini USB Logic Analyzer 24MHz 8 Channel UART IIC SPI Debug for Arduino, Raspberry Pi, FPGA, ARM Board

  • 8 Channels usb logic analyzer, each channel sampling rate up to 24MS/s..
  • On-board 4 indicator leds for ch0 to ch3. Easy to observe the low speed signal..
  • The signal could be analyzed with many standard protocols, to get more straightforward communication data..
  • Compatiable with most ready-made logice analyzer tools, such as sigrok PluseView etc..
Check Stock

35?4400MHz Portable Spectrum Analyzer,3.5 ”TFT Handheld Frequency Analyzer Amplitude Bandwidth Frequency Signal Generator,Tracking Generator Steps Sweep Signal Generator (PLZ-SA354400A 3.5inch LCD)

  • [ Accurately Track ] This portable spectrum analyzer 35‑4400MHz Equipped with a tracking source TG, the frequency of the signal output by the tracking source can accurately track the tuning frequency of the spectrum analyzer..
  • [Output Range]35MHz‑4.4GHz signal source output range, can display and analyze a simple spectrum.The input dBm scope is -80dBm~0dBm, output dBm is 0dBm..
  • [4 Major Modes ]Four major modes: Network mode, Spectrum mode, Point frequency mode, Sweep mode. After power on, the default mode is Network mode..
  • [3.5 Inch Touch Display ] Touch function, without button operation, you can directly click on the touch screen to operate..
  • [Portable ] Handheld spectrum analyzer Easy to carry and tiny , powered by USB-C cable,it can be easily hand‑held for measurement or carried to various places.Made of aluminum alloy material, wear resistance and can provide long service time..
Check Stock

Vibrometer Digital Split Type Vibration Meter LCD Displays Acceleration Sensor Gauge Handheld Vibration Analyzer Grey

  • TWO TEMPERATURE UNITS: It can measure the environment temperature with 2 temperature units (℃ and ℉), temperature measurement 0℃ - 60℃, temperature accuracy is ±2℃.
  • MEASURING RANGE: Digital vibration tester has wide measurement range of acceleration: 0.1~199.9m/s2 peak, vibration acquisition is piezoceramic accelerometer.
  • FUNCTION: Vibration gauge analyzer adopts piezoelectric acceleration transducer transfer the vibration signal in to electrical signal, analyze the input signals, and show the vibration speed, acceleration, displacement, can meet your different using need.
  • LCD DISPLAY: Vibrometer gauge LCD displays measurement result and conditions directly, three and a half digit display, clear display for easy reading.
  • APPLICATION: Vibration analyzer tester is widely used in mechanical manufacturing, electric power, chemical engineering, space flight and aviation and other fields.
Check Stock

Satlink WS6966 Satellite Finder Meter MPEG4 DVB-S2 Meter Satlink WS-6966 HD Satellite Finder

  • WS-6966 Support formal international standard video and audio encoding.
  • Satlink WS-6966 Satellite Finder Meter has 4.3 Inch High Definition TFT LCD Screen.
  • Support DISEQC 1.0,1.1,1.2 and 22khz Tone.
  • Software upgrade via USB port. Easy to carry..
  • Measurement Type: signal strength,quality, BER, S/N,PWR, MER.
  • Sound and Light Alarm for Locking Signal.
Check Stock

RF Explorer Digital Handheld Spectrum Analyzer 6G Combo Plus - Slim

  • ...trength and the high quality baked varnished paint provides a unique glossy finish. The device is designed and manufactured to last many years of demanding usage in the field, with internal rechargeable Lithium battery for hours of continuous usage..
  • [Advanced features] – Included advanced high-resolution Spectrum Analyzer mode, WiFi Analyzer mode, Tracking SNA. Internal firmware is continuously updated with additional features and functions to improve the device capabilities..
  • [Free Computer software] - When connected to a Windows, Linux or Mac computer the analyzer can display advanced high resolution graphics, including Power Meter and Spectrum Analyzer real time charts, historical charts, save data to CSV files and export to other tools such as WW6 or MatLab, define markers and limit lines and much more. Free open source API and libraries are available to customize your own applications and services..
  • [Tracking mode enabled] – When combined with RF Explorer Signal Generator the analyzer can perform full tracking SNA to define Gain, Attenuation and SWR for 1 and 2 port RF devices such as filters, amplifiers and antennas..
Check Stock

SDRGEEK TinySA Handheld Tiny Spectrum Analyzer 2.8 Inch Touching Display 100KHz-960MHz Screen Spectrum Analyzers Signal Generator with Battery

  • 【With Two Inputs】Spectrum analyzer with two inputs, fine quality MF/HF/VHF input for 0.1MHz-350MHz, lesser quality UHF input for 240MHz-960MHz. Switchable resolution bandpass filters for both ranges between 2.6KHz and 640KHz..
  • 【MF/HF/VHF Input】Input step attenuator from 0dB to 31dB for the MF/HF/VHF input. Color display showing 290 scan points covering up to the full low or high frequency range..
  • 【Portable and Convenient】Rechargeable battery allowing a minimum of at least 2 hours portable use. Connected to a PC via USB it becomes a PC controlled spectrum analyzer..
  • 【Wide Application】When not used as spectrum analyzer it can be used as signal generator, MF/HF/VHF sinus output between 0.1MHz-350MHz, UHF square wave output between 240MHz-960MHz..
  • 【Package Included】1 * Spectrum Analyzer.
Check Stock

USB Logic Analyzer Device with USB Cable 5MHz 24MHz 8CH 8 Channel UART IIC SPI Debug Logic Analyzer Professional Microcontroller Device Network Analyzing Set for Ardu-ino FPGA ARM M100 SCM

  • Logic analyzer is a waveform test device similar to an oscilloscope. It collects specified signals and displays them to developers through graphics or data statistics. Developers use these graphical timing signals to analyze hardware or software errors in accordance with the protocol..
  • Logic analyzer is an indispensable device in design. It can quickly locate errors, find and solve problems, especially when analyzing timing, such as 1wire, I2C, UART, SPI, CAN and other data, the application of logic analyzer to solve problems is very fast..
  • Plug the DuPont cables into the logic analyzer interface one by one. After the DuPont cables are inserted, they will be divided into 2 rows. The upper row of 5 logic analyzers corresponds to the silk screen on the left side of the shell, and the bottom one row corresponds to the silk screen on the right. Before testing the signal, please connect the GND channel of the logic analyzer to the GND pin of the board, otherwise the measured data will be unreliable..
  • If the logic analyzer works at 24M, the USB device must not only provide a 24M communication rate, but also must ensure that other devices occupy USB resources before the 4 buffers are filled. For these reasons, the logic analyzer cannot always work at the sampl....
Check Stock