Reviews Shunt Resister- BestItemr.com

Hazard Warning LED Flasher Relay for GM Turn Signal Relay Flasher Module, Fix Hyper Flash, Replace LM487 10383321 15231201 15764135

Fixes Turn Signal ProblemLed flasher relay fixes for GM, GMC, Chevrolet problem with no turn signals or with 4 way flashers coming on when the directional is actuated..
FeatureIf you're going to do a LED light upgrade for your GM vehicle, this turn signal relay module is a must have item - solve the hyper flash problem with simple a plug and play..
FitmentsLed turn signal flasher compatible with 2003 2004 2005 2006 Silverado Tahoe, Sierra, Yukon, Avalanche, Suburban. Replace Part Numbers: LM487, 10383321, 15231201, 15764135..
NoteUse this gm led flasher relay for led turn signal, never cut your factory wires and install a load resister. (use the load resister basically shorting out the circuit).
Installation TipsTake out the dash cluster cover, remove two screws on the bottom of the steering wheel cover panel. Take the panel out. Use a clamp wrench to take out the original flasher, plug this flasher relay in, test the signals to see if hyper flashing goes away, then you are done..

About CG:CG ammeter shunt is made of high quality brass and Manganin, is Sanded to make more shiny , sealing treatment to be used for a long time..
relative humidity:less than or equal to 95% (35℃)..
Temperature Rise:20ppm,When the change of temperature tends to be stable,if rated current is below 50%, the temperature will be not higher than 80℃,if rated current is above 50%, the temperature will be not higher than 120℃..
Over-load ability:rated current 120%, 2 hours.It is not recommended that the practical used current over the 80% of rated current for a long time..

LightKeeper Pro fixes most incandescent light sets in seconds with the squeeze of the trigger.
LightKeeper Pro's Quick Fix Method repairs the #1 cause of light set failure known as a Shunt Issue (internal bulb failure).
When the Quick Fix Method doesn't do the trick because the light set does not have a Shunt Issue, you can use the Audible Voltage Detector to locate the interruption in the circuit.
Includes Bulb Tester, Fuse Tester, Bulb Puller, Storage Compartment for spare bulbs & fuses, 10 clear replacement bulbs (2.5V, 170mA).
Even includes Batteries (1.5 Volt Alkaline).

Fits Both The 009 And Stock Vacuum Advance Distributors that use Bosch 044 Points.
Specification For Coils Are Primary 3.4 Ohms, Secondary 7.8 Ohms (Must Be Used With A Coil With An Internal Resister Or External Ballast Resistor Must Be Used).

INA219 module is an I2C interface with a drift, bi-directional current / power monitor integrated circuit (IC), and further expand the energy-saving....
INA219 I2C Bi-directional DC Current Power Supply Sensor, Working Voltage 3~5V.
INA219 module small size, low cost, high accuracy. It not only can monitor the voltage drop across a shunt resistor on the sensing shunt supply....
INA219 can be achieved within the maximum error accuracy of +1% from -40° C to 85° C temperature range, the maximum offset is 100 uV. The....
Appliaction:The module is used for I2C port zero drift / bidirectional current / power monitoring sensor module. The device is available in a SOT23....

Measurement Range:0-30A Accuracy of Class: 2.0.
(Appalication)-Pointer instruments are often used to measure current or voltage, monitor circuits and replace damaged instruments..
(Purpose)-It is widely used in mobile phone maintenance machinery and equipment, power electronic measurement, laboratory measurement and calibration, on-site circuit detection, operation, maintenance and management of power system power plants, substations, data center computer rooms, power distribution facilities, mechanical equipment, ships, aviation, transformers,voltage regulators and other industries..
(Material)-Transparent plastic case&(Size)-Meter Panel(Approx): 2.75X2.36X0.98" / 70x60x25mm(L*W*T).
(Package contents)-Ammeter and a 30A shunt with a small package of mounting accessories (the wiring tools for connecting the ammeter to the shunt are purchased separately).

MNJ 4-in-1 DC MULTIMETER – with 1.0 grade measuring accuracy, it combines Voltage, Current, Power and Energy measurement in 1 combo, super compact and lightweight that can be portable and easily used.
SUPER LARGE DIGITAL DISPLAY – 51x30mm easy reading LCD screen, clearly displays all testing figures at the same time, while the recessed button used to control the backlight, reset energy value.
BONUS CURRENT SHUNT – it comes with a 100A/75mV current shunt, suitable for large range measurement, no need to waste extra money to get another 1.Plus, we offer 1 Year MNJ Motor Warranty and friendly customer services.
UNIQUE VOLTAGE ALARM FUNCTION – the backlight and voltage value will flash simultaneously if the testing voltage is beyond alarm threshold (6-90V factory alarm value), and it can be set if needed.
DATA STORAGE DESIGN – it is designed to automatically storage the last testing data when suddenly powered off and the energy value can be reset by a short press after long pressing the function button for seconds.
MNJ Motor provides you 30-Days Money Back/ Replacement and 24 months Warranty, Within 4 hours Response.

☛Why Choose Us☚: 1. 0.5mm Fat Leg, Accurate for Breadboard 2. Clear Printed Resistance 3. Standard 5 Color Bands 4. Arranged Neatly to Avoid Bending 5. Much Better Performance than Carbon Equivalent.
Power: 1/2 W Watt, Fix Resistance: 10Kohm, TOL: ±1%.
Diameter: 3mm, Film Length : 9mm, 100 pcs Pieces Single Fixed Resistor with Line.
☛Feature☚: High Stability, Low Noise, Low Temp Coefficient, Precision Characteris Tics ohms, Long Working Life Resister.
☛Application☚: For/on Precise Electronic Circuits, Arduino, Electronic And Electrical Communication Equipments, Musical Instrument or Applications,Electronics.