Reviews Shaft Length

Lubegard 60902 Automatic Transmission Fluid Protectant, 10 oz. , RED

  • Rear Drive Shaft Axle Assembly For 2004-2008 Ford F-150 RWD 4.2L 4.6L 144.7 or 144.5 Wheel base, w/10 Bolt Differential Cover.
  • Shaft Length Compressed (in): 90 3/4" | Shaft Diameter (in): 2-7/8 Inch | Measure the Length to Confirm before Order.
  • This complete drive shaft assembly is pre-balanced and ready to install with 100% new yokes, tubes, constant velocity (CV) joints and universal joints..
  • Ready to install - this drive shaft arrives pre-balanced to make installation quick and simple.
  • 100% new - this drive shaft is made from all new components so there's no core charge or return hassle.
Check Stock

uxcell 4mm Drive Shaft, L250mm Shaft, L200mm Sleeve, D36mm Propeller, Fit for 3.17mm Motor Shaft

  • The material OF SHAFT - stainless steel..
  • SIZE - suit for motor shaft diameter: 3.17 mm.
  • drive shaft size: 250 x 4 mm (length*diameter).
  • shaft sleeve size: 200 x 9.5 mm (length*outer diameter).
  • NOTE - there are bearings between the shaft and the shaft sleeve, it could hold on high strength and speed in a whirl..
  • APPLICATION - compatible with DIY model..
  • PACKAGE CONTENT - 1 x Drive shaft assemble kit..
Check Stock

ULTNICE Quartz Clock Mechanism Battery Operated DIY Wall Clock Movement Repair Parts

  • Size About : 5.6 x 5.6 x 1.5cm/2.2 x 2.2 x 0.6inch. The total length of the shaft is 12mm, and the length of the yellow spiral is 5mm. ( Please Note: Please measure the shaft of you clock mechanism you need before buying ! ).
  • Diameter : The Minute Shaft Diameter is 3.6-3.7mm, and the Hour Shaft Diameter is 5.5mm. Screw Shaft Diameter 7.6mm..
  • For DIY quartz wall clock replacement movement part, applicable framless 3D Wall clock. The error is less than +-1.5 seconds/day, and the power consumption is less than 200 microamps..
  • Powered by 1 AA battery(Not Included, You can use No.5 AA batteries, carbon batteries, alkaline batteries. Cannot Use Rechargeable Batteries)..
  • IMPORTANT : This model is a 5mm ordinary shaft, which is suitable for clock panel thickness of not more than 4mm, otherwise the front nut cannot be tightened and the clock cannot run ! !(Due to different measuring tools and measuring methods, the measured length may be slightly different from the actual one. Thank you for your understanding!!!).
Check Stock

HVAC Motor 1/100 HP 3000 RPM 120V 3.3

  • Price For: Each Body Dia.: 3.3" Motor Shaft Design: Flat Motor Service Factor: 1.00 Frame: 3.3 Motor Bearings: Sleeve Phase: 1 Max. Ambient Temp.: 40....
  • Duty: Continuous Mounting Pattern: 2-7/8 x 2-7/8 RPM Range: 1801-3000 Voltage: 120 Voltage Compatibility: 115, 120 Shaft Length: 3-1/2" Mounting Stud....
  • Length Less Shaft: 2-7/16" Shaft Dia.: 1/4" Country of Origin (subject to change): Mexico.
Check Stock

DLE Engines 30-C28#3 DLE30 Electronic Ignition

  • 【PROFESSIONAL DIESEL ENGINE】4-stroke Air- Cooled Diesel Engine.Through advanced software analysis and optimization design, the reliability of....
  • 【DIESEL ENGINE SPECIFICATIONS】Model：186F Туре：Single-cylinder, vertical, 4-stroke air- cooled diesel engine Combustion system：Direct....
  • 【DIESEL ENGINE PARAMETER】Oil System: Pressure and Splash Engine Cooling Type: Forced Air Cooling.
  • 【SHAFT PARAMETER 】 Shaft Type: Keyed - Straight Shaft Diameter: 1" Diameter, 1/4" Keyway Shaft Length: 72.2mm (2-5/6" Length) Shaft I.D. Thread....
  • 【WIDE APPLICATION】It is widely used in small agricultural machinery, such as micro-tiller, pastoral management machine, irrigation and drainage....
Check Stock

UniTry 2Pcs Microwave Turntable Coupler, Microwave Oven Roller Guide Support (Shaft Length: 0.94"/ 24mm)

  • ✅ Reminder: There are two different sizes of the shaft length (17mm, 24mm). In order to buy the correct coupler, you need to measure the shaft length of your old coupler. If you select a wrong size, the turntable plate may be unable to turn or not in balance on the support..
  • ✅ Shaft Dimensions: Length 0.94″/ 24mm, Outer Diameter 0.43″/ 11mm..
  • ✅ Material: Made of high quality plastic for long life usage, an ideal replacement for the old or broken one..
  • ✅ Compatibilty: Universal replacement part for microwaves (the old part should have the same size).
  • ✅ Package Contents: 2 x Microwave Turntable Coupler (Shaft Length: 0.94″/ 24mm).
Check Stock

Evaporative Cooler Motor, 115V, Cradle

  • Price For: Each Hz: 60 Motor Service Factor: 1.00 Motor Bearings: Ball Standards: UL, CSA Motor Enclosure Design: Open Dripproof Ring Dia.: 2-1/2" Resilient Ring Dia.: 2-1/2" Ins. Class: B Phase: 1 Max. Ambient Temp.: 40 Degrees C Length Less Shaft: 7-15/16" Motor Sub Application: Evaporator Cooler Motor Application: HVAC/R Ring to Ring Center: 7-7/16".
  • Ambient Temperature: 40C Item: Evaporative Cooler Motor Motor Thermal Protection: Auto Motor Design: Split-Phase Motor Mounting Type: Cradle Base No. of Speeds: 2 Shaft Dia.: 5/8" Frame: 56 Voltage: 115 Shaft Length: 1-7/8" Overall Length: 9-13/16" Nameplate RPM: 1725/1140 HP: 3/4, 1/3 Voltage Compatibility: 115, 120, 115/208-230, 115/230, 120/240 Full Load Amps: 9.8/6.4.
  • Motor Shaft Rotation: CW/CCW Country of Origin (subject to change): China.
Check Stock

Continuous Sweep Mini Quartz Movement - Medium Shaft

  • Quartz Clock Movement Kit: This clock mechanism is perfect with its clock parts for repairing, replacing, or making your own DIY clock project. The clock movement design keeps foreign matter out of the gears, resulting in years of trouble-free operation..
  • Clock Movement Measurements: Total hand shaft length is 20.6 mm (13/16 inch). Total shaft diameter is 7.9 mm (5/16 inch)..
  • Maximum Clock Dial Thickness: 7.9 mm (5/16 inch). Refers to the thickness of the combined material (clock face material and support board the dial is mounted to) that the threaded length of the movement shaft travels through. The hardware adds 1.6 mm (1/16 inch) making the total length of the threaded bushing 9.5 mm (3/8 inch). For finding a replacement, measure the threaded portion of the shaft on your old clock movement. If the length is shorter or equal to 9.5 mm (3/8 inch), this is suitable..
  • Clock Hands Measurements: Total black spade hour and minute hand length is approx. 63.5 mm (2 1/2 inch), total red second hand length is approx. 69.9 mm (2 3/4 inch). The Q-80 movement will have a step motion that creates a ticking sound, powered by an AA battery..
  • Package Contents Include: One easy to assemble quartz clock movement, one hour hand, one minute hand, one second hand, and hand....
Check Stock

Bettomshin Drive Shaft w Propeller and Universal Joint for RC Boat, L200mm Shaft, L150mm Sleeve, D36mm Propeller, Fit for 3.17mm Motor Shaft

  • 【Parameters】- Shaft length: 20cm/7.8".
  • Suit for motor shaft diameter: 3.17mm/0.12".
  • 【High Quality】- RC boat propeller shaft kit is made of stainless steel,corrosion-resistant,wear-resistant and good sealing..
  • 【Feature】- There is bearings between the shaft and the shaft sleeve, it could hold on high strength and speed in whirl..
  • 【Application】- The propeller shaft is suitable for the different types of boats ,simulation compatible with DIY RC model, such as RC boat toy ,RC submarine and so on..
Check Stock

Quartex Standard Push-On Movement with Hex Nut - Long Shaft

  • Quartz Clock Movement Kit: This clock mechanism is perfect with its clock parts for repairing, replacing, or making your own DIY clock project. The clock movement design keeps foreign matter out of the gears, resulting in years of trouble-free operation..
  • Clock Movement Measurements: Total hand shaft length is 28.6 mm (1 1/8 inch). Total shaft diameter is 7.9 mm (5/16 inch)..
  • Maximum Clock Dial Thickness: 17.5 mm (11/16 inch). Refers to the thickness of the combined material (clock face material and support board the dial is mounted to) that the threaded length of the movement shaft travels through. The hardware adds 1.6 mm (1/16 inch) making the total length of the threaded bushing 19.1 mm (3/4 inch). For finding a replacement, measure the threaded portion of the shaft on the old clock movement. If length is shorter or equal to 19.1 mm (3/4 inch), this is suitable..
  • Clock Hands Measurements: Total black spade hour and minute hand length is approx. 63.5 mm (2 1/2 inch), total red second hand length is approx. 69.9 mm (2 3/4 inch). The Q-80 movement will have a step motion that creates a ticking sound, powered by an AA battery..
  • Package Contents Include: One easy to assemble quartz clock movement, one hour hand, one minute hand, one second hand, and hand ....
Check Stock

Quartex Standard Push-On Movement with Hex Nut - Short Shaft

  • Quartz Clock Movement Kit: This clock mechanism is perfect with its clock parts for repairing, replacing, or making your own DIY clock project. The clock movement design keeps foreign matter out of the gears, resulting in years of trouble-free operation..
  • Clock Movement Measurements: Total hand shaft length is 14.3 mm (9/16 inch). Total shaft diameter is 7.9 mm (5/16 inch)..
  • Maximum Clock Dial Thickness: 3.2 mm (1/8 inch). Refers to the thickness of the combined material (clock face material and support board the dial is mounted to) that the threaded length of the movement shaft travels through. The hardware adds 1.6 mm (1/16 inch) making the total length of the threaded bushing 4.8 mm (3/16 inch). For finding a replacement, measure the threaded portion of the shaft on the old clock movement. If the length is shorter or equal to 4.8 mm (3/16 inch), this is suitable..
  • Clock Hands Measurements: Total black spade hour and minute hand length is approx. 63.5 mm (2 1/2 inch), total red second hand length is approx. 69.9 mm (2 3/4 inch). The Q-80 movement will have a step motion that creates a ticking sound, powered by an AA battery..
  • Package Contents Include: One easy to assemble quartz clock movement, one hour hand, one minute hand, one second hand, and hand ....
Check Stock

Franklin Sports NHL Philadelphia Flyers Team 48-Inch Vinyl Hockey Stick (Right), Junior, Orange

  • Fused shaft blade construction, full coverage vinyl graphic wrap.
  • Shaft: multi-ply poplar/birch wrapped vinyl.
  • Fused shaft blade construction, Full coverage vinyl graphic wrap.
Check Stock

XIAOSHI 2-Sets 8mm 100mm Case Hardened Plated Steel for Linear Motion Rods Shafts Guides

  • Linear Motion Shaft: /Diameter: 8mm /Length: 100mm /Material: Stainless Steel /Hardness: Surface hardness-55-60HRC.
  • Hardened layer-0.8mm /Surface treatment: Chrome Plated,Smoothness Ra0.8.
  • Horizontal Shaft Holder: /Material: Aluminum Alloy /Compatible Model: SHF 8A /Shaft Diameter: 8mm /Locking Bolt: M4 /Clamping Bolt: M5 /Dimensions: 43*10*5mm (W*L*T).
  • Linear Slide: /Material: Bearing steel /Slide Bush Method: LM8UU /Dynamic Basic Loading: 274CN /Static Basic Loading： 392CON /Dimensions: 34*30*22mm (W*L*F).
  • This linear motion shaft of 8 mm in diameter and in different Length is steel plated and case hardened, and is suitable for use with linear support blocks and closed Type slide units in linear motion applications..
  • Package Included: /2 x Linear Motion Shaft /4x Horizontal Shaft Holder /4x Linear Slide.
Check Stock