Reviews Serial Breakout Board

HiLetgo Smallest SIM800L GPRS GSM Breakout Module Quad-Band 850/900/1800/1900MHz SIM Card Slot Onboard with Antenna 3.7~4.2V

  • Mini GSM / GPRS breakout board is based on SIM800L module, supports quad-band GSM/GPRS network, available for GPRS and SMS message data remote transmission..
  • The board features compact size and low current consumption. With power saving technique, the current consumption is as low as 1mA in sleep mode..
  • It communicates with microcontroller via UART port, supports command including 3GPP TS 27.007, 27.005 and SIMCOM enhanced AT Commands..
  • AT command interface with "auto baud" detection..
  • TTL serial port for serial port, you can link directly to the microcontroller.
Check Stock

Treedix Breakout Board Module with Pin Header for Teensy 3.5/3.6 Compatible with Arduino

  • The breakout board expands the connection with all the processor functions. The breakout board is well-made, gold-plated on both sides to prevent oxidation..
  • All pins on the breakout board are accessible, Teensy3.5 is compatible with arduino integrated development environment (IDE).
  • Simple and easy to assemble, can be used in conjunction with a breadboard, the spacing between the holes on the board: 2.54mm.
  • The breakout board module can easily extend the Teensy 3.5/3.6 project to industrial control, home automation or other applications..
  • Note: The package is not include Teensy development board and breadboard.
Check Stock

SparkFun FTDI Basic Breakout - 3.3V Development Tool with USB Mini-B Connector Save Space and Money in Your DIY Electronics Projects Pinout of This Board Matches The FTDI Cable

  • Save space by using this genuine FTDI FT232RL USB to serial IC breakout to program your microcontroller.
  • Has TX and RX LEDs that allow you to see serial traffic on the LEDs to verify the board is working.
  • Designed to decrease the cost of (Arduino-compatible) development and increase ease of use. Includes auto-reset feature.
  • The pins labeled BLK and GRN correspond to the black wire on the FTDI cable that is GND, green is DTR.
  • Uses a SMD 6-pin header on the bottom, which makes it smaller and more compact.
Check Stock

Treedix Breakout Board Module with Pin Board for Teensy 4.1/3.5/3.6 Compatible with Arduino

  • The breakout board expands the connection with all the processor functions, the circuit board is well-made, gold-plated on both sides to prevent oxidation.
  • Simple and easy to assemble, it can be used in conjunction with a breadboard, the distance between the holes on the board is 2.54mm.
  • Widely compatible: all pins on the breakout board are accessible, and can be used in conjunction with Arduino IDE and Arduino compatible hardware.
  • Use this breakout board module to easily extend Tennsy 4.1 project to industrial control, home automation or other applications.
  • Note: The package is not include teensy development board.
Check Stock

KEYESTUDIO Motor Driver HAT Breakout Board for BBC Microbit TB6612FNG with Terminal Block Serial Pins

  • Specially researched and developed this motor driver breakout board to facilitate the micro bit to drive DC motor..
  • Four motor control modes: Forward/Reverse /Brake /Stop.Access to 3Pin headers connection..
  • Integrated with 3.3V and 5V voltage-regulator chip. Comes with a serial communication port for Bluetooth module..
  • EXCELLENT QUALITY: solder is very clean, everything is aligned nicely, all boards are well packed after function,voltage, current testing, protected in a beautiful box..
  • Up to FCC and CE Standard: made from environmentally friendly components and materials, as well as environmentally friendly production technology, it is really safe..
Check Stock

HiFiBerry HighPi Raspberry Pi Case - Raspberry Pi4

  • High quality ABS plastic case, designed and made in Canada, Large internal volume for HATs, break-out boards, or heat sinks, Vents on three sides double as fly-through cable ports, Self-adhesive rubber feet included, set of 4, Matte finish hides fingerprints.
  • External dimensions: 97 x 66 x 41mm, Internal volume for breakout boards: 90 x 60 x 28.8mm.
Check Stock

2Pcs NRF24L01+PA+LNA RF Wireless Transceiver Module with SMA Antenna 2.4G 1100m & Wireless Module with Breakout Adapter On-Board 3.3V Regulator

  • NRF24L01+PA+LNA Wireless Transceiver Module is a 2.4GHz ISM band transceiver, compatible with Raspberry Pi. Auto-acknowledge and auto-retransmit abilities.
  • Support up to six channels of data reception.
  • the transceiver come with power amplifier and SMA antenna, which make the effective communication distance has been greatly expanded..
  • A host microcontroller can communicate and configure the nRF24L01+ over a 4-pin Serial Peripheral Interface (SPI). The configuration registers are accessible through the SPI connection. Configurable parameters include frequency channel (125 selectable channels), output power, and data rate (data rates: 250kbps, 1Mbps, and 2Mbps)..
  • RF24L01+ Breakout Adapter: Small power on SMD LED indicator, On-board 3.3V voltage regulator, which accepts +5V power supply input and provides 3.3V for the attached "nRF24L01+" module..
  • Applications:It can be wildly used in wireless remote control such as RC planes/vehicles, wireless audio, wireless voice transmission such as VoIP, wireless networks, smart home,somatosensory devices, RFID, NFC etc..
  • Package Included:2 x NRF24L01+PA+LNA Wireless Transceiver Module+2 x SMA Antenna+2 x NRF24L01+ Breakout Adapter.
Check Stock

Vilros BBC Micro:bit Breadboard Adapter/Expansion Board

  • Vilros BBC Micro:bit Breadboard Adapter/Expansion Board.
  • Make wiring your microbit a breeze with the T-Shaped Breakout board that conveniently plugs into your breadboard..
  • Important: Breakout Board Only-Does NOT include A BBC Microbit.
Check Stock

UMLIFE 5pcs NRF24L01+PA+LNA RF Transceiver Module with SMA Antenna 2.4 GHz 1100m + 5pcs NRF24L01 Wireless Module with Breakout Adapter On-Board 3.3V Regulator for Arduino

  • It can be wildly used to wireless remote control, somatosensory devices, RFID, NFC, smart grid, smart home, wireless audio etc..
  • 5PCS NRF24L01 8 Pin Socket Breakout Adapter Board: On-board AMS1117-3.3 chip, a simple socket breakout board which is for 8-Pin NRF24L01 wireless module.
  • 5PCS NRF24L01+PA+LNA RF Transceiver Module with SMA Antenna: Built-in 2.4Ghz antenna: available software to set the address, only received local address when output data(Provide interrupt instruction), can be directly connected to a variety of microcontrollers.
  • RF24L01+ Breakout Adapter: Small power on SMD LED indicator, On-board 3.3V voltage regulator, which accepts +5V power supply input and provides 3.3V for the attached "nRF24L01+" module..
  • The packing list includes: 5 * NRF24L01+PA+LNA Wireless Transceiver RF Transceiver Module.
Check Stock

Ximimark 5Pcs 16CH Analog Digital Multiplexer Breakout Board Module CD74HC4067 CMOS Precise Module For Arduino

  • This is a breakout board for the very handy 16-Channel Analog/Digital Multiplexer/Demultiplexer CD74HC4067. This chip is like a rotary switch - it internally routes the common pin (COM in the schematic, SIG on the board) to one of 16 channel pins (CHANxx)..
  • It works with both digital and analog signals (the voltage can’t be higher than VCC), and the connections function in either direction..
  • To control it, connect 4 digital outputs to the chip’s address select pins (S0-S3), and send it the binary address of the channel you want. This allows you to connect up to 16 sensors to your system using only 5 pins!.
  • Since the mux/demux also works with digital signals, you can use it to pipe TTL level serial data to or from multiple devices. For example, you could use it to connect the TX pins of 16 devices to one RX pin on your microcontroller. You can then select any one of those 16 devices to listen to. If you want two-way communications,you can add a second board to route your microcontroller's TX line to 16 device's RX lines. By using multiple boards, you can create similar arrangements for I2C,SPI,etc..
  • The internal switches are bidirectional, support voltages between ground and VCC, have low “on” resistance and low “off” leakage, and to prev....
Check Stock

Treedix Prototype Breakout Breadboard Adapter Expansion Board for BBC Micro:bit

  • This is a connector that fits directly to the edge contacts of a BBC micro:bit. The connector has 80 pins, but because of the different widths of the micro:bit edge contacts, some of the micro:bit contacts will map to more than one of this connector's pins. Also, the back half of the pins are not used at all..
  • The edge connector gives access to all the important pins on the bottom edge of the micro:bit. Check the datasheet for the pin spacing and orientation. This connector is best used with a custom PCB..
  • This breakout board for edge connectors allows intermediate and advanced users to connect micro:bit to breadboards and other sensors, motors, LEDs, etc..
  • We can use it in many ways, it is highly recommended to use our breakout board.
  • Through the breakout board, we broke through all 21 GPIO, power and ground pins in the form of 0.1"..
Check Stock

DORHEA 5Pcs ESP32 Development Board GPIO Breakout Board 30Pin Type-C Micro USB Dual Interface ESP32 Shield 30P Ultra-Low Power Dual Core ESP32-DevKitC-32 ESP-WROOM-32 ESP-32 ESP-32S Expansion Board

  • ESP32 shield 30P expansion board, supports two power supply : DC 6.5-16v and USB 5V.
  • The GVS output power supply can be 5V or 3.3V, which is more convenient to match the external 5V electronic module sensor..
  • The breakout board is only fit for 30PIN ESP32. Please confirm your esp32 board pins width is coincide with the pin width of the breakout board.
  • ESP32 breakout board GPIO 1 into 2 only can compatible with 30 pins ESP32S ESP32 , just for ref asin: B086MJGFVV B086MLNH7N B086MGH7JV.
  • This module is safe, reliable, and scalable to a variety of applications. Stable and highly reliable.Great contact and stable signal transmission for your esp32 board.
Check Stock

Opto 22 G4PB8 G4 8 Channel I/O Module Rack

  • Screw Terminal Block Breakout Board for Arduino MKR..
  • With the breakout board, you can easily extend Arduino MKR projects to industrial control applications..
  • PCB mount Terminal Block: pitch 5.0mm/0.197.
Check Stock