Reviews Reversible Tap And Drill

CS Unitec 3/4' Weldon Tap Holder for 3/4' Diameter Taps - Mag Drill Tap Collet - Fits Standard Weldon Chucks On Most Magnetic Drill Presses (TCM 3/4)

  • FAST TAPPING: Adapter for 3/4" diameter taps, fast changeout. Tap chuck collets available for holding up to 3/4" diameter taps..
  • NO SPECIAL TOOLING NEEDED: Collets fit standard tap shanks. Can be used with variable speed, reversible and other mag drills..
  • 3/4" WELDON SHANK: Fits most mag drill chucks. Industry standard, 2 flat shank..
  • COMPACT: For easy transport, storage and use without impact on magnetic drill stroke..
  • HEAVY DUTY: High quality, long lasting, professional grade, Made In Germany. Recommended use with MAB 465 magnetic drill (ASIN B08QGSPFDD).
Check Stock

6 Packs Titanium Combination Drill & Taps Bit Set SAE 6-32nc 8-32nc 10-32nc 10-24nc 12-24nc 1/4-20nc.

  • COMBINATION DRILL & TAP & COUNTERSINK- No more using a drill to drill the hole and then tapping it out later with another tool. All in one and works great and save a lot of time and trouble..
  • HANDY TOOLS – These drill tap bits are must have if you fabricate a lot.
  • you can use the in aluminum, plastic, and so on.
  • Go slow, once the tap is doing its thing, make sure not to strip the threads by bottoming it out..
  • HIGH VERSATILITY – Set of 6 drill tap bits in SAE sizes 6-32NC, 8-32NC, 10-24NC, 10-32NC, 12-24NC, ¼-20NC, with 1/4inch hex quick-change shank, fit Electric hand drill, impact drill, bench drill, electric screwdriver and other tap machines..
  • EASY TO USE - Each tap drill is engraved with its size convenient for you to choose the suitable size with a glance. A tapered end on hex shank can prevent excessive knocks.
  • Back taper exceeds the tap to prevent over-drilling and damage to the thread..
  • WORRY-FREE – This Drill Tap Bits set comes with a portable storage case for convenient use and store. If you encounter any problems in using th....
Check Stock

TEMO 2 pc 6-32 Combination Drill and Tap Multi Use Deburr Countersink Hex Bit

  • 2 pc 6-32 Combination Drill and Tap Multi Use Deburr Countersink Hex Bit.
  • Made of high speed M2 steel. For use with: steel, copper, brass, aluminum. drill, tap and deburr in one operation..
  • Drill, tap and deburr in one operation. Tapered tap design prevents thread damage from over-drilling..
  • One piece construction guarantees proper drill for tap size. | 135 self-centering split point tip. 10 gauge (3.5mm) capacity. Usage suggestions: use of cutting coil recommended. clean tap of metal chips to extend life. reverse drill to back out after completing tap..
  • US-BASED CUSTOMER SERVICE: Available by chat, email, phone, or visit us at our customer service center in La Crosse, WI..
Check Stock

Irwin Tools Tap and Drill Sets, 13-Pieces

  • This tap and drill bit set produces a thread that is strong and easy to tap.
  • High-carbon steel plug taps are great for general-purpose threading.
  • 135° split-point drill bits give fast, precise drilling.
  • Set pieces: 6 – 32 NC, 8 – 32 NC, 10 – 24 NC, 10 – 32 NF, 12 – 24 NC and 1/4″ – 20 NC plug taps and 7/64″, 13/64″, #29, #25, #21 and #16 drill bits, plus a T-handle tap wrench.
Check Stock

szgate 5PCS Combination Drill Tap Bit Set Screw Tapping Hex Shank HSS MetricImperial Plug Drill Bits Hand Tools 6-32NC, 6-32NC (3.5mm)

  • The wide range of drill tap bit set helps you with tasks like drilling, tapping, deburring and countersinking, all with this single kit. The split point tip resists walking and penetrates faster into the material. Along with fast penetration, the power drill makes your life easy by saving your time and energy..
  • Durable taps are made from hardened high-speed steel (HSS ) vs carbon steel for longer life,which can drill, tap, deburr and counter holes on wood, copper, brass, aluminum, sheet metal and plastic.
  • This is a SAE drill tap set, so it has high versatility. Each tap drill is engraved with a label, which is convenient for you to choose the size that suits you. Quick Change ¼-inch (6.35mm) hex shank has a tapered end to prevent excessive knocks. Back taper exceeds the tap to prevent over-drilling and damage to the thread..
  • Can be used to tap various threads. including 6 SAE sizes: 6-32NC, 8-32NC, 10-24NC, 10-32NC, 12-24NC, ¼-20NC,1/4inch hex quick change shank fit Electric hand drill, impact drill, bench drill,electric screwdriver and other tap machine.
  • Easy to Carry and Use,As the Drill Tap Bits set comes with a portable storage case you can carry it anywhere you go. If you encounter any problems or are not satisfied with the products while usi....
Check Stock

6 Pcs HSS Drill Tap Bit Set, Titanium Coated Combination Drill & Taps M3, M4, M5, M6, M8, M10, 1/4\ Hex Shank, for tapping, drill a hole and cut new threads

  • The wide range of drill tap bit set helps you with tasks like drilling, tapping, deburring and countersinking, all with this single kit. The split point tip resists walking and penetrates faster into the material. Along with fast penetration, the power drill makes your life easy by saving your time and energy..
  • Durable taps are made from hardened high-speed steel (HSS ) vs carbon steel for longer life,which can drill, tap, deburr and counter holes on wood, copper, brass, aluminum, sheet metal and plastic.
  • This is a SAE drill tap set, so it has high versatility. Each tap drill is engraved with a label, which is convenient for you to choose the size that suits you. Quick Change ¼-inch (6.35mm) hex shank has a tapered end to prevent excessive knocks. Back taper exceeds the tap to prevent over-drilling and damage to the thread..
  • Can be used to tap various threads. including 6 SAE sizes: 6-32NC, 8-32NC, 10-24NC, 10-32NC, 12-24NC, ¼-20NC,1/4inch hex quick change shank fit Electric hand drill, impact drill, bench drill,electric screwdriver and other tap machine.
  • Easy to Carry and Use,As the Drill Tap Bits set comes with a portable storage case you can carry it anywhere you go. If you encounter any problems or are not satisfied with the products while usi....
Check Stock

Left Hand Drill Bit Set (10 pc, Silver & Gold), Metal Extractor Bits to Remove Stripped Broken Screws & Bolts w/Iron Storage Case by Mata1

  • HEAVY DUTY REMOVAL SET – These left-handed reverse twist extractors are USA-designed with clean steel technology, HSS strength & high HRC hardness.
  • Suitable for removing hardened, damaged, rusted & painted-over screws or bolts.
  • HARD & TOUGH – The hex shank extraction bits range in diameter from 3/32″ to 5/8″, while the lefthand drill bits range in diameter from 5/64″ to 19/64″ with 118-degree split points for high-speed drilling.
  • CARRY CASE – Ideal tool box to organize & hold the remover drill bits for any craftsman, dad, husband, boyfriend, or wife.
  • DRILL & REMOVE – Select bit size appropriate to the damaged screw/bolt.
  • Insert left-hand drill bit into drill & set drill to reverse.
  • Drill a hole about 1/16” deep into the screw/bolt.
  • Select corresponding extractor & use a mallet/hammer to pound it into the screw/bolt.
  • Use drill, wrench, or tap handle to thread the screw bolt out.
  • HANDY GADGETS – Mata1 is committed to provide lasting quality tools.
  • Mata1 reversible drill bit sets provide an assortment of sizes for removal of stuck bolts & screws.
Check Stock

H.S.S. Tap & Drill Full Bundle, UNC, UNF and Metric

  • 3 H.S.S. Tap & Drill Full Bundle for almost all cases..
  • 18 Pc H.S.S. Tap and Drill Set, Unf in Metal Box, 0001-0050.
  • 18 Pc Hss Tap and Drill Set, Metric, 0001-0052.
  • 18 Pc H.S.S. Tap and Drill Set, U.N.C, 0001-0040.
Check Stock

6 Packs Combination Drill & Taps Bit Set, Screw Tapping in SAE Size 6-32nc 8-32nc 10-32nc 10-24nc 12-24nc 1/4-20nc with Anti-Rust Black Coating, 1/4” Hex Shank and Storage Case

  • COMBINE DRILL and TAP at the same time - All in one and works great and save a lot of time and trouble when doing threads for hinges or other projects.
  • No more using a drill to drill the hole and then tapping it out later with another tool..
  • HIGH VERSATILITY – Set of 6 drill tap bits in SAE sizes 6-32NC, 8-32NC, 10-24NC, 10-32NC, 12-24NC, ¼-20NC, with 1/4inch hex quick-change shank, fit Electric hand drill, impact drill, bench drill, electric screwdriver and other tap machines..
  • HANDY TOOLS – These drill-tap bits are must have if you fabricate a lot.
  • you can use them in aluminum, plastic, wood and other thin soft material metal panel.
  • When you use it, make sure it is perfectly straight, take your time, go slow, use lubrication to prevent breaking the bit in the hole..
  • EASY TO USE - Each tap drill is engraved with its size convenient for you to choose the suitable size with a glance. A tapered end on hex shank can prevent excessive knocks.
  • Back taper exceeds the tap to prevent over-drilling and damage to the thread..
  • WORRY-FREE – This Drill Tap Bits set comes with a portable storage case for convenient use and store. If you encounter any problems in using the products, please feel free to contact us for satisfactory customer service..
Check Stock

6Pcs Combination Drill and Tap Set, Metric Thread M3-M10 Screw Tapping Tool 1/4\ Hex Shank Titanium Plated HSS

  • Applicability: This product includes 1/4 inch hexagon shank HSS drill bits and tap kits. Metric M3, M4, M5, M6, M8, M10 threaded countersunk screws can be tapped together with this drill tap..
  • Material: These drill taps are made of titanium-coated high-speed steel and have a longer service life..
  • Specifications: M3 x 0.5mm pitch, M4 x 0.7mm pitch, M5 x 0.8mm pitch, M6 x 1.0mm pitch, M8 x 1.25mm pitch, M10 x 1.5mm pitch..
  • Design: The drill tap adopts a spiral groove design, and the chip removal process will be better..
  • Accuracy: These drill taps are used for tapping on machines and are usually more precise because human error is eliminated..
Check Stock

Century Drill & Tool 93201 1/8-27 NPT Tap and 21/64' Drill Combo Pack

  • Tap and drill Combo pack offers correct drill size for the tap in one convenient package.
  • Tap offers precision cut threads, accurately formed for consistent, exact threading.
  • Tap is heat treated and tempered for file hard threads, and longer, useful life.
  • Tap designed for hand cutting applications.
  • Drill bit made of premium grade high speed steel.
Check Stock

AUTOTOOLHOME Titanium Combination Drill Tap Bit Set 13PCS SAE and Metric Tap Bits Kit for Screw Thread Drilling Tapping Deburring Countersinking

  • Titanium Combination Drill tap bits are made of high speed steel 4341, which can ensure sharp, fast execution and retain strength and efficiency. The surface is treated with a titanium alloy, which greatly improves the cutting performance of the drill, is more wear-resistant and prolongs the service life..
  • 13pcs drill tap kit include SAE and metric sizes, Suitable for most commonly used screw tapping.SAE Included 6-32NC, 8-32NC, 10-24NC, 10-32NC, 12-24NC and 1/4-20NC,Metric included M3 x 0.5, M4 x 0.7, M5 x 0.8, M6 x 1.0, M8 x 1.25, M10 x 1.5 , Includes storage case and quick change adapter for easy bit switching.
  • Drill, tap, deburr and countersink in one quick and easy action,and complete job on copper, brass, aluminum, sheet metal ,mild steel and plastic.work completely, greatly save processing steps and time costs, and improve work efficiency..
  • Each drill tap bit is engraved with the right size, which is convenient for you to choose the size that suits you. Strong hex shank ensures strong connection to drill.a tapered end to prevent excessive knocks. Back taper exceeds the tap to prevent over-drilling and damage to the thread..
  • Included convenient swivel storage case,Swivel feature props up tap drill bits and securely holds them in place until ready t....
Check Stock

Hanson 1765531 Pts Drill Plus Tap Combo 6-32' Number 36 for Tap Die Extraction

  • This tap and drill set contains a convenient HCS tap and HSS drill bit.
  • Self-aligning taps start and thread straight virtually every time.
  • Great for through holes and irregular surfaces.
  • Plug taps are ideal for general purpose threading.
  • Special chip-breaking technology cuts chips easier.
Check Stock