Reviews Relay Controlled Power

AITRIP 8 Pack 3V 1 Channel Relay Power Switch Module with Optocoupler Opto Isolation High Level Trigger for IOT ESP8266 Development Board

  • 【30VDC 250VAC Load】 Equiped with high-current relay, AC250V 10A.
  • DC30V 10A, each relay has normally open and normally closed contact. Can be selected by jumper relay and TTL or ground..
  • 【High Level Trigger】The relay module is triggered by high level signal, which can be input from microcontroller IO..
  • 【 3V/3.3V power relay module】- This Relay Board provides a single relay that can be controlled by any 3V/3.3V digital input from your microcontroller IO..
  • 【Wide Application】- These 3v relay board works well with ARM /PIC /AVR /MCU/Raspberry/CNC machine/ PS4/3.3V /NodeMCU/ ESP8266 module etc..
  • 【Long Life】 - Fast response time less than 20ms and long lifetime up to 100,000 times snap action with diode freewheel protection..
Check Stock

Painless Performance 80132 Single Pole, Double Throw Relay, 40 Amp

  • ★ The 8-channel relay module is equipped with transistors, diodes and optocouplers to switch higher loads safely, reliably and with little power. The module is also equipped with generously dimensioned relays in order to be able to reliably carry out many switching processes..
  • ★ 5V 8-channel relay module, each relay requires 70mA for switching (switching capacity AC: max. 250V / 10A.
  • ★ 5V 8-channel relay module can be controlled directly with a microcontroller Raspberry Pi, Arduin, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic, etc..
  • ★ The relay acts as a switch that responds to a signal from the Arduin. Because of this, it is widely used in IoT projects to control lights and other electronic devices..
  • ★ Application: MCU control, PLC control, industrial area, smart home.If you need this relay, you can buy it directly. If there is a problem during use, you can contact us at any time to refund or replace it..
Check Stock

ELEGOO 8 Channel DC 5V Relay Module with Optocoupler Compatible with Arduino UNO R3 MEGA 1280 DSP ARM PIC AVR STM32 Raspberry Pi

  • 5V 8-Channel Relay interface board, each one needs 70mA Driver Current.
  • Equiped with high-current relay, AC250V 10A.
  • Each relay has normally open and normally closed contact. Can be selected by jumper relay and TTL or ground..
  • With power indicator,8-way road has a status indicator. With a relay coil to absorb the diode protection..
  • Standard interface that can be controlled directly by microcontroller (Arduino , 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic).
  • The 8 channels are optically isolated, safe, reliable, anti-interference. Widely used for all MCU control, industrial sector, PLC control, smart home control。For a complete data sheet for this relay board, please download it from: http://dwz.win/UhW.
Check Stock

WinnerEco 5pcs 1 Channel DC 5V Relay Switch Module for Raspberry Pi ARM AVR

  • 1-channel relay interface board which can be controlled directly by a wide range of microcontrollers. Controllers includes AVR, PIC, ARM, PLC, etc..
  • Relay output maximum contact is AC110V ~ AC250V 10A and DC30V 10A..
  • Standard interface can be directly connected with microcontrollers..
  • Red working status indicator for power on indication.Green working status indicator for relay the switch..
  • It can control various appliances and other equipments with large current.Widely used for all MCU control, industrial sector, PLC control, smart home control..
Check Stock

AOICRIE 12V 16-Channel Relay Interface Board Module Optocoupler LED LM2576 Power for Arduino DIY Kit PiC ARM AVR

  • ★12V 16-Channel Relay interface board, and each one needs 15-20mA Driver Current.
  • ★Equipped with high-current relay, AC250V 10A.
  • ★The control signal voltage range: the trigger signal is low 0-2V.
  • ★Standard interface that can be controlled directly by microcontroller (for Arduino , 8051, AVR, PIC, DSP, ARM, ARM, MSP433, TTL logic).
  • ★DC 12V 16 Channel Relay Module Interface Board With Optocoupler Protection LM2576 Power for Arduino DIY Kit.
Check Stock

GAEYAELE 1PCS GRT8-M 16A Multifunction Time Relay with 10 Function Choices AC220V OR AC/DC12V-240V Relay(GRT8-M2,A230)

  • Special 10 Functions: 5 time functions are controlled by the power supply voltage, 4 time functions are controlled by the control input, and 1 latch relay function..
  • Instructions: Comfortable and well-arranged function and time-range setting by rotary switches..
  • Time range: The time scale is 0.1s-10 days, divided into 10 ranges..
  • Relay Status : Its working status is indicated by the LED indicator..
  • Product Size: Ultra-small size, only 18mm width, 35mm rail mounting..
Check Stock

Weewooday 15 Pieces 5V Relay Module 1- Channel Relay Control Boards with Optocoupler Isolation High and Low Level Trigger Expansion Board

  • Relay module: this relay board supports high and low level trigger and can be controlled by any 5V digital output of the microcontroller.
  • Parameter details: maximum load of normally open interface: AC 250v/ 10A, DC 30v/ 10A, trigger current is 5mA.
  • The 5v relay control board adopts SMD optocoupler isolation, which has strong driving ability and stable performance.
  • Practical design: with fault-tolerant design, the relay module will not operate even if the control line is disconnected.
  • All interfaces can be provided through directly connected terminal s since the humanized interface design, it is very convenient to use.
  • High compatibility: the relay module can be directly controlled by the 5V logic signal provided by the microcontroller, suitable for 8051, Raspberry Pi, PIC, DSP, ARM, AVR, MSP430, TTL logic, etc..
  • Wide application: this 5V relay board can be applied with Raspberry/ CNC machine/ ARM/ PIC/ AVR/ MCU/ PS4 and more.
Check Stock

Baomain SSR-60DA 60A Solid State Relay Module 4-32VDC / 24-480VAC + Heat Sink

  • Photocoupler isolation between input control signal and controlled power, isolation surge voltage up to 7500V..
  • Input signal turn-on voltage DC 3 to 32V, turn-off voltage DC 0 to 0.8V. LED indication for relay turn-on..
  • Output voltage range: AC 90 to 250V(50/60Hz). Maximum on-state average current 3 Amp. Maximum on-state current 10 Amp (003c 10 seconds). Non repetitive surge peak on-state current: 120 Amp (003c20mS). Load type: General purpose..
  • This is a simple and practical solid state relay module, which is very convenient to use, for Arduino, Raspberry Pi, ESP32, PLC or other projects. The GPIO of these controllers are directly connected to this relay input to control the mains power, and it is suitable for most loads less than 350 Watts (for 115VAC)/700 Watts (for 230VAC)..
  • Compact ABS plastic case and wires connect for easy mount. Two screw mounting holes are convenient for you to fix it on the wall or wooden board. Of course, you can also choose not to lock the screw..
Check Stock

GAEYAELE 1PCS GRT8-M 16A Multifunction Time Relay with 10 Function Choices AC220V OR AC/DC12V-240V Relay(GRT8-M1,AC/DC12V-240V)

  • Special 10 Functions: 5 time functions are controlled by the power supply voltage, 4 time functions are controlled by the control input, and 1 latch relay function..
  • Instructions: Comfortable and well-arranged function and time-range setting by rotary switches..
  • Time range: The time scale is 0.1s-10 days, divided into 10 ranges..
  • Relay Status : Its working status is indicated by the LED indicator..
  • Product Size: Ultra-small size, only 18mm width, 35mm rail mounting..
Check Stock

Acxico 2 pcs ESP8266 ESP-01S + 5V WiFi Relay Module Smart Home Remote Control Unlock Board

  • This module uses genuine relays and normally open interfaces. High stability and low power consumption..
  • Strong driving ability, stable and reliable performance. High efficiency, fine workmanship, and durable..
  • Add one more ESP-01S module. This smart relay module is based on the ESP-01S WIFI module design. It can be used to DIY your own smart switch. It can be remotely controlled by the mobile phone APP and provides APP and LUA source programs. It's easy to use right away..
  • The package includes：2 pcs ESP8266 ESP-01S Relay module, relay WIFI smart socket (with ESP-01S).
  • We are very grateful for all customers’ opinions to improve sales, if you are not satisfied, please contact us to find the best solution.
Check Stock

UMLIFE 2PCS Temperature Controller Module with Case, XH W1209 LED Display Digital Thermostat Module with Waterproof NTC Probe -50~110 Electronic Temperature Temp Control Module Switch

  • The W1209 thermostat module controller has a sensor input, keys, LED display, and a relay. It can be reprogrammed for control, timing, or counting..
  • Temperature Measurement Range: -50~110. Control Precision: 0.1 celsius.Input Power (DC): 12V.
  • Output: 1 Channel Relay Output, Capacity: 10A.
  • Electronic digital thermostat with a 3-digit LED display, extremely bright. Operation both in heating and cooling to easily control equipment and devices..
  • The output is electronically controlled by a microprocessor, to guarantee the utmost precision of intervention and an excellent resolution of reading temperature..
  • The NTC probe is waterproof and allows to control the temperature even of fluids, allowing the controlled heated or coolingNote: The wood laminate case is the clear plastic case. You need to tear the wood outside layer off carefully, the outside layer is very thin. (It can protect the inside to prevent scratches.) And you need to assemble and install the case by yourself, it comes disassembled with tiny bolts and nuts.)..
Check Stock

AEDIKO 4pcs DC 5V Relay Module 2 Channel Relay Board with Optocoupler Support High or Low Level Trigger

  • Normally Open Interfaces Maximum Load : AC 250V/10A, DC 30V/10A.
  • 2 Channel Relay Module 5V Comes with High-Current Relay,Trigger Current : 5mA.
  • 5V Relay Module is 2 Channel Isolated, Each Relay Can Individually Switch On/Off by An Opto-Isolated Digital Input.
  • Relay Module Designed With Fault-Tolerant , Even If The Control Line Breaks, The Relay Will Not Move.
  • With Optical Coupling Isolation,Triggering More Reliable and Stable.
  • 2 Channel Module Equipped With Screwed Terminal Plate and Fixed Bolt Holes,Standard Interface Can Connect With Microcontrollers and be Controlled by a Wide Range of Microcontrollers.
Check Stock

5v Relay Board Relay Module 1 Channel Opto-Isolated High or Low Level Trigger

  • 【1 Channel Relay Module】- This Relay Board provides a single relay that can be controlled by any 5V digital output from your microcontroller..
  • 【Main Specification】- Peak Load of NO Connector: AC125~250V/10A, DC28~30V/10A.
  • 【Adopted SMD Optocoupler Isolation】- The isolation circuit prevent damages to I / O port by relay switch current..
  • 【Wide Application】- These 5v relay board works well with ARM /PIC /AVR /MCU/Raspberry/CNC machine/ PS4 etc..
  • 【Humanization Design On Interfaces】- All interfaces can be directly wired out through the terminals..
Check Stock