Reviews Rail to rail Input

Juried Engineering TLV271IP TLV271 T271IP Single 16V, 3MHz, 550-uA/ch, Rail-to-Rail Output Operational Amplifier Op Amp Breadboard-Friendly IC DIP-8 (Pack of 2)

  • The TLC2274 are quadruple operational amplifiers from Texas Instruments. The TLC2274 devices exhibit rail-to-rail output performance for increased dynamic range in single- or split-supply applications..
  • Output Swing Includes Both Supply Rails, Low-Input Bias Current: 1-pA Typical.
  • Low Noise: 9 nV/√Hz Typical at f = 1 kHz, Fully-Specified for Both Single-Supply and Split- Supply Operation.
  • Common-Mode Input Voltage Range Includes Negative Rail, High-Gain Bandwidth: 2.2-MHz Typical.
  • High Slew Rate: 3.6-V/µs Typical, Low Input Offset Voltage: 950 µV Maximum at TA = 25°C.
Check Stock

Electronics-Salon 20 Watt(VA) DIN Rail Mount Power Transformer Module (in: 115VAC, Out: 24VAC)

  • Secondary output: Full load 24VAC /0.84A, No load 27.6VAC..
  • Epoxy resin encapsulated safety isolating transformer. Epoxy resin cast in vacuum. Fire resistance property in accordance with UL94-V0. Dielectric strength: 3500V/1min 5mA. no-load loss less than 1.2 watt. Insulation grade: grade B. Temperature rise: less than 28C..
  • Screw terminal block easy to connect wires. With primary input fuse, fuse holder easy to replace the fuse. Output power indicator LED..
  • DIN rail mount carrier: High quality Taiwan DINKLE fireproof nylon material DIN rail mount carrier (not China low quality carrier), can support width 35mm / 32mm / 15mm rail..
Check Stock

Electronics-Salon 5 Watt(VA) DIN Rail Mount Power Transformer Module (in: 115VAC, Out: 24VAC)

  • Secondary output: Full load 24VAC / 208mA, No load 28.8VAC..
  • DIN rail mount carrier: High quality Taiwan DINKLE fireproof nylon material DIN rail mount carrier (not China low quality carrier), can support width 35mm / 32mm / 15mm rail..
  • Epoxy resin encapsulated safety isolating transformer. Epoxy resin cast in vacuum. Fire resistance property in accordance with UL94-V0. Dielectric strength: 3500V/1min. No-load current less than 20mA, no-load loss less than 0.5 watt. Insulation grade: grade B. Temperature rise: less than 22C..
  • Screw terminal block easy to connect wires. With primary input fuse, fuse holder easy to replace the fuse. Output power indicator LED..
Check Stock

Juried Engineering Microchip MCP602-I/P MCP602 Dual Operational Amplifier Op-Amp 2.8MHZ 2.3V/us DIP-8 Breadboard-Friendly (Pack of 5)

  • The MCP602 operational amplifiers (op amps) utilize an advanced CMOS technology, which provides low bias current, high speed operation, high open-loop gain and rail-to-rail output swing..
  • Specifications rated from 2.7V to 5.5V supplies, Rail-to-rail swing at output.
Check Stock

Juried Engineering Microchip MCP602-I/P MCP602 Dual Operational Amplifier Op-Amp 2.8MHZ 2.3V/us DIP-8 Breadboard-Friendly (Pack of 4)

  • The MCP602 operational amplifiers (op amps) utilize an advanced CMOS technology, which provides low bias current, high speed operation, high open-loop gain and rail-to-rail output swing..
  • Specifications rated from 2.7V to 5.5V supplies, Rail-to-rail swing at output.
Check Stock

JESSINIE 3Pcs MCP6022 Amplifier Module CJMCU-622 Microphone Sound Sensor Module 3V 10MHz Rail-to-Rail Operational Amplifier Module High Performance Rail-torail Input Output OP Amps

  • The MCP602 operational amplifiers (op amps) utilize an advanced CMOS technology, which provides low bias current, high speed operation, high open-loop gain and rail-to-rail output swing..
  • Specifications rated from 2.7V to 5.5V supplies, Rail-to-rail swing at output.
Check Stock

CZH-LABS DIN Rail Mount 12 Amp Solid State Relay SSR Module in 4~32VDC Out 100~240VAC 1 Channel

  • MOC3043 Phototriac and BTA12-600B triac (the heatsink is electrically insulated)..
  • Input Action Voltage DC 3 to 32V. LED indication for each channel. Anti-reverse protection diode..
  • Output Load Voltage range AC 100 to 240V (50/60Hz). Maximum on-state average current: 12 Amp. Isolation: Phototriac. Zero cross: Yes..
  • Dual input terminal block, you can flexibility to configure the input control mode: Individual / Common Positive / Common Negative..
  • DIN rail mount, Taiwan DINKLE fireproof nylon material DIN rail mount carrier (not China low quality carrier), can support width 35mm / 32mm / 15mm....
Check Stock

Juried Engineering Microchip MCP602-I/P MCP602 Dual Operational Amplifier Op-Amp 2.8MHZ 2.3V/us DIP-8 & DIP Sockets with Machined Round Contact Pins Holes 2.54mm Breadboard-Friendly (1 Pair)

  • The MCP602 operational amplifiers (op amps) utilize an advanced CMOS technology, which provides low bias current, high speed operation, high open-loop gain and rail-to-rail output swing..
  • Specifications rated from 2.7V to 5.5V supplies, Rail-to-rail swing at output.
Check Stock

1 pc OPA1611 Module Low Power Precision op amp Audio Dedicated Audio Amplifier

  • Name: Low Power Precision Operational Amplifier Audio Dedicated Preamp Size: 50mm X 50mm Supply voltage range: up to ±18V.
  • Can be arbitrarily changed to positive amplification, reverse amplification, shooting with the integration circuit and other forms. The OPA1611 is ultra-low noise and is a powerful audio system..
  • The main features Excellent sound quality Ultra-low noise: 1.1nv/vHz at 1kHz Ultra low distortion: 0.000015% 1kHz High conversion rate: 27V/H Bandwidth: 40MHz (G=+1) Open loop gain: 130dB Unity gain stability Low quiescent current: 3.6 per channel Rail-to-rail output Wide Supply Range: ±2.25V to ±18V.
  • Application Professional audio equipment Analog and digital mixing console Audio Test and Measurement Preamplifiers microphone Broadcast recording equipment High-end A/V receiver.
  • The opa1611 bipolar input op amps achieve a low 1.1nv/VHz noise density at ultra-low distortion Hz of 0.000015% at 1kHz. The opa1611 provide a rail-to-rail output swing with a 2K2 load at 600mV, thereby increasing headroom and maximum dynamic range..
Check Stock

MCP6002-I/P DIP-8 1 MHz Gain Bandwidth Product, Low-Power Op Amp Pack of 6 Pcs

  • Rail-to-Rail Output, Specified Temperature Range: Industrial Grade: −40°C to 125°C.
  • Wide Bandwidth: 3 MHz, Input Bias Current: 1 pA.
  • High Slew Rate: 2.4 V/µs, Input Noise Voltage: 39 nV/√Hz.
  • Supply Voltage Range: 2.7 V to 16 V, Supply Current: 550 µA/Channel.
  • Example Applications: E-Bike, Power Banks, Smoke detectors, Solar Inverters, Low-Power Motor Controls, Battery-Powered Instruments, Building Automation.
Check Stock

CZH-LABS DIN Rail Mount 2 Ports Passive RJ45 PoE Power Injection Board Power Over Ethernet Injector Module.

  • Simple Power up 2 Passive 10/100Mbps PoE devices by one power source Application use for Access Points, IP cameras, IP phones, etc..
  • Power Input terminal block for all PoE power supply, each port serial a recoverable fuse(fuse value 1.1Amp / 72V). Power Expansion Output terminal....
  • Switch On/Off to save electricity while not use, LED indication for switch On/Off status..
  • Specifications: Terminal Block Power Input: 12VDC - 60VDC, maximum current 10Amp.
  • Termianl Block Expansion Output: maximum current 10Amp.
  • High quality fireproof nylon material DIN rail mount carrier (not China low quality carrier), can support width 35mm / 32mm / 15mm rail, and the....
Check Stock

DEE ZEE DZ99603 Stainless Steel Side Rail

  • Direct replacement - this truck bed rail cover replaces the original part and matches the original color and texture.
  • No special tools required - integrated retaining tabs require no hardware to install.
  • Durable construction - this bed rail protector is made of UV-resistant plastic.
  • Quality tested - this part has undergone vehicle try-on testing to ensure proper fit.
  • Ensure fit - to make sure this part fits your exact vehicle, input your make, model and trim level into the garage tool.
Check Stock

CZH-LABS DIN Rail Mount 8 Amp Solid State Relay SSR Module in 4~32VDC Out 100~240VAC 8 Channels

  • MOC3043 Phototriac and BTA12-600B triac (the heatsink is electrically insulated)..
  • Input Action Voltage DC 3 to 32V. LED indication for each channel. Anti-reverse protection diode..
  • Output Load Voltage range AC 100 to 240V (50/60Hz). Maximum on-state average current: 8 Amp, maximum on-state current 12 Amp (< 10 seconds). Isolation: Phototriac. Zero cross: Yes..
  • Terminal Block: Wire range: 24 ~ 12 AWG / 2.5mm square. Strip length: 7mm. Screws - M2.5, steel, Cr3+ Zn plated. Pin header and Cage - Brass..
  • DIN rail mount, Taiwan DINKLE fireproof nylon material DIN rail mount carrier (not China low quality carrier), can support width 35mm / 32mm / 15mm rail. FR-4 fiber glass PCB, dual copper layers..
Check Stock