Reviews Pushing Cylinder

PAGOW Spark Plug Boot Wire Removal Tool Ignition Coil Puller for Volkswagenn Audi VW Hand Install Repair Tool

  • Best Compatibility: The spark plug wire puller installer can perfect match with Volkswagen and Audi vehicles with standard prong plug caps on each side (not recommended for non-VW/Audi plug leads). Volkswagen – New Beetle 2.0 engine AZJ (AEG), Golf IV & V 1.6 engine (AVH), 1993-2005 2.0L 4 cylinder (AZG), 1998-2006 1.8L 4 cylinder (BBW), 2006 and later 2.0L 4 cylinder turbo (BDC).
  • Audi – 1998-2006 1.8L 4 cylinder turbo (BEV), 2006 and later 2.0L 4 cylinder turbo (BGD)..
  • Size Inforamtion: The size of spark plug boot removal tool kit: 12.6inch (32cm) overall length, 3.75inch x 0.4inch x 1.2inch (9.5cm x 1cm x 3cm) handle, 9.25inch (23.5cm) shaft, 2.2inch x 0.8inch (5.6cm x 2cm) boot end..
  • Wide Applications: The spark plug puller tool suitable for Bora, Mercedes, Smart, and other Volkswagen and Audi vehicles with similar engines and standard prong plug caps on each side..
  • Easy to Use:Perform spark plug change when engine is cold to prevent the heads from stripping. After pulling the plugs, we recommend applying lubrication to make the job easier. When installing wires, refrain from pushing too hard without the tabs aligned on the tool to prevent the boot end from spreading and getting stuck..
  • Material:The handle of ignition coil puller is made of hard p....
Check Stock

VEVOR Double Acting Hydraulic Cylinder 2'' Bore, Top Link Hydraulic Cylinder 10'' Stroke, Retracted 18\ Extended 26 Hydraulic Side Link Swivel Eye Bearing w/Check Valve for Tractors, Category 1, 2

  • High Tensile Steel Structure: This hydraulic lifting cylinder is a welded double acting cylinder. It has a high tensile honed cold drawn hydraulic tube, a polished piston rod, and sturdy threaded glands. With bearing design on base ends. Carbon steel construction ensures its longevity and features a max 6700 lbs pushing force and 4500 lbs pulling force..
  • 2"-2.5" Bore 10" Stroke Top Link: The top link cylinder is built under specific dimensions. Bore: 2"-2.5". Stroke Length: 10". Rod Size: 1". Pin Size: 0.8". With retracted min length 20" and extended max length 28". Double Pilot Check Valve Port Size: G3/8. Max Pressure: 5076PSI. Max Flow Rate: 20 L/ min. Opening Pressure: 50.76 PSI..
  • Swivel Eye Bearing Design: There is a spherical swivel eye bearing design on both ends. Due to the sturdy and flexible bearings, you can quickly fix and install the cylinder on your tractors or min excavators. Joint Bearing Width: 2". Thickness 0.8". Durable enough to hold a lot of force..
  • With Check Valve & Fully Tested: The well-assembled and thoroughly tested tractor top link hydraulic cylinders also come with a double pilot operated check valve to help hold the cylinder and prevent drift. The assembled inside sealing rings guard the high performance of sealing, accessi....
Check Stock

Titan Attachments 72in Clamshell Root Grapple Rake Fits John Deere Global Euro Loaders, Twin 3,000 PSI Cylinders, Brush Debris Landscaping Grapple

  • DESIGNED FOR GLOBAL EURO CARRIERS: This grapple attachment was explicitly made for Global Euro Carriers typically found on John Deere. It easily hooks up to John Deere tractor with the Global Carrier Mounting System and other tractors with the euro global mounting system..
  • GREAT FOR LANDSCAPING: This landscaping grapple is ideal for picking up and moving brush, debris, and other odd-shaped material. It features an extra-wide opening that makes pushing and gripping large loads easy..
  • TWIN 3000 PSI CYLINDER: To help your tractor operate smoothly, this attachment utilizes a twin 3000 PSI cylinder. Its convenient cylinder provides powerful lifting capability to clear your yard or back acre..
  • DIMENSIONS: Weighing 805 LB, this 72" wide grapple provides an opening height of 48". This attachment has an overall side thickness of 0.5". The teeth of the grapple rake measure 24" in length and are 0.5" thick..
  • NOTE: When you order this grapple rake, you will need to provide your phone number so the trucking and shipping company can schedule delivery..
Check Stock

JET AHJ-12, 12-Ton Air/Hydraulic Bottle Jack (456612)

  • TROUBLE-FREE OPERATION: Industrial pneumatic motor reduces lifting time..
  • MULTI-FUNCTIONAL USE: Capable of lifting, pushing, spreading, bending, pressing, or straightening..
  • PROVEN RELIABILITY: Electric-welded base and cylinder virtually eliminates leaks..
  • EASY STORAGE: Includes a heavy-duty blow molded carry case..
  • MEETS HIGH STANDARDS: Complies with ANSI/ASME B30.1 and PALD-1 Standard..
Check Stock

Bonvoisin 20T 4 Inch Hollow Hydraulic Cylinder Jack Porta Power Ram Single Acting Lifting Cylinders 4\ Stroke for Machinery Shipbuilding

  • [Hollow Design] - The hollow design of the cylinder jack allows it to be used for pushing or pulling, which can meet your different needs..
  • [Split Design] - The porta power ram is portable, small in size and easy to store. But it must be used with a hydraulic/electric pump. For example, they can all be used with CP-700(ASIN: B08QV222RP)..
  • [Automatically Retract] - This hollow ram cylinder can automatically retract to the initial height after the oil return valve of the pump is loosened, which is easy and convenient to operate..
  • [Connector & Dust Cover] - The connectors adopt threaded ZG3/8" joint, which is screw-locked and has a compact structure. And the dust cover can prevent dust from entering to protect the connector..
  • [Wide Applications] - This hydraulic jack can be widely used in power, chemical, steel, bridges, shipbuilding, machinery and other industries! However, it does NOT apply to cars..
Check Stock

Yaheetech 2 Pack Mesh Office Desk Chairs, Ergonomic Height Adjustable Computer Chairs, Executive Chair Rolling Chair for Girls, Boys Black

  • Robust construction: Our mid-back office chairs are constructed of hard-wearing nylon mesh, durable star base, solid rolling casters and SGS-certified pneumatic cylinder, which is capable of holding up to 125kg/275lb..
  • Claw base & 360 degrees casters: Twisting and turning about is integral within the office. So we adopt a reliable claw base and equip it with 5pcs 360-degree swivel casters, ensuring fluent and quick movement and keeping up your quick pace of work..
  • Ergonomic backrest: Curved backrest perfectly lines up with the human body line and supports your spine’s natural curve. The lumbar support system resembles a pair of hands, pushing up and holding your low back..
  • Office recliner: By simply pushing the lever or pulling it out, our mesh office chairs can be tilted and leaned backward or locked in place for various sitting positions. A tilt tension control knob under the seat is provided to adjust the recliner tension..
  • Pneumatic seat-height adjustment: The seat height of this computer mesh chair can be simply adjusted from 36.5cm/14.4'' to 46.5cm/18.3'' by a little push-up/press down at the lever under the seat according to your needs..
Check Stock

CNC Mountain Bike V Brake Set, Bicycle V Brake for Front/Rear，1Pair

  • ...o brake, the rotor will not move while ensures great performance. One-way hydraulic brakes for mountain bike system is to brake by pushing aside the rotor which is easy to make the rotor deformed..
  • 【Adjust Tightness】: Front /Rear bicycle hydraulic disc brake caliper are made of premium aluminum material with oil cylinder driven two -way brake pad clamp . MTB hydraulic disc brakes with internal fine-tuning screws can be used to adjust the tightness of the brake inner wire to achieve the desired bicycle hydraulic brake feel..
  • 【Upgrade Design】: HB-100 hydraulic bike brakes uses a new hydraulic line pull clamp technology. The block of the HB-100 mechanical disc brake caliper is equipped with built-in brake oil, and then the brake clamp is used to control the bicycle disc brake kit conversion of the hydraulic clamp. The cylinder of the clamp is built-in brake oil..
  • 【Application Bikes】: Lining Pulled Hydraulic Disc Brake Suitable for mountain E-Bike,bikes, road bikes and folding bikes, MTB, scooter, fat bike..
  • 【Note】: Hydraulic disc brake adapter. Please do not remove the yellow pad before installation, and pinch the brake lever, otherwise it will cause oil leakage or scrap the oil disc.
Check Stock

5 tons 0.28\ Stroke Hydraulic Cylinder Lifting Jack ram Low Height FPY-5

  • Low height:5 ton Ultra-Thin Hydraulic Lifting Cylinders Stroke 7 mm（0.28"） provide the maximum power to height ratio. A compact, low height cylinder design is ideal for confined spaces where other cylinders will not fit.
  • strength and durability: hard chrome plated high quality steel plungers plunger avoid break ing when it is overloaded.
  • Heavy duty spring return: faster retraction increasing productivity, ideal for pulling and pushing in testing, maintenance, and tensioning applications.
  • Oxide finish resists corrosion ensuring long life,Extended height(mm) 48 （1.89"）.
  • Need to work with hydraulic pump: recommend cp-180.
Check Stock

Park Tool BKD-1 - Hydraulic Brake Bleed Kit for DOT Fluid

  • ▶▶The low resistance oiler is made of plastic steel and its chemical stability exceeds m-edical standards.All-round disc brake oil change tool kit..
  • ▶▶All-round disc brake oil change tool kit. View the various brake oil video tutorials by scanning the QR code on the mobile phone.
  • ▶▶A chemically stable low resistivity injector can provide an objective smoothness even when pushing a high consistency shock absorber without decay due to prolonged use.
  • ▶▶【Two Types Of Oil Storage】Filling Cylinder And Funnel, Which Can Deal With The Brake Handle Of Any Structure Flexibly. Can Be Used To Collect Waste Oil When The Bottle Is Linked To The Caliper..
  • ▶▶View the various brake oil video tutorials by scanning the QR code on the mobile phone..
Check Stock

AUTOOL Ultrasonic Wave Fuel Injector Cleaner and Tester Automotive Fuel Injection Systems Cleaning Tools for All Petrol 6 Cylinder Vehicles Motorcycle

  • 【Why Need It】The performance of the injector plays a vital role in the power of each engine. Due to the fuel quality, the injector cannot work normally, causing serious carbon deposits in the cylinder.
  • accelerating the cylinder bore and piston ring, causing unstable idling, increased fuel consumption, weak acceleration, difficulty in starting, excessive emissions, and complete blockage of the injector. Cause damage to the engine, so the injector should be cleaned regularly..
  • 【Digital Display】With the help of microcomputer control and digital display, the equipment makes possible automatic cleaning, testing injectors and real-time monitoring of the dynamic values..
  • 【Automatic Cleaning and Testing】Fuel pressure control through microcomputer offers stable pressure control and largeadjustable range, which is suitable for all EGI vehicles and can help to achieve automatic cleaning and testing of injectors..
  • 【Adopting Humanization Design】Automatic fuel draining through preset programs for some test items. Test liquid/detergent can also be drained by pushing a button on the control panel after the test.can make the....
Check Stock

Mikuni Super BN Series 38mm Carburetor BN38-34-8113

  • The Mikuni RS Series Carburetors were designed and built in response to the needs of the worlds top motorcycle road race and drag race teams..
  • They required carburetors which could satisfy the precise fuel metering demands and high flow volume required by highly modified race engines..
  • And yet, also provide the smooth, controllable throttle response that is needed by any rider pushing his motorcycle to its limits on the race track and under any high performance applications..
  • The carburetors need to meter fuel correctly under a wide range of atmospheric conditions and engine tuning modifications while being easily accessible for trackside tuning changes which need to be made quickly..
  • Designed for in-line four cylinder performance motorcycle applications, the Mikuni RS Series Radial Flat Slide Carburetors offer superior horsepower gains with their maximum flowing smoothbore induction tract and radial flat slide design..
Check Stock

PETCHOR HB-100 Line Pulling Hydraulic Disc Brake Calipers, Mechanical Disc Brakes for MTB, Mountain Bike, E-bike and Electric Bike 2PCS Front/Rear Red

  • 【Braking System】：Two hydraulic bike brake pads clamp the disc rotor to brake, the rotor will not move while ensures great performance. One-way brake system is to brake by pushing aside the rotor which is easy to make the rotor deformed..
  • 【Adjust Tightness】: Front /Rear bicycle hydraulic disc brake caliper are made of premium aluminum material with oil cylinder driven two -way brake pad clamp . MTB hydraulic disc brakes with internal fine-tuning screws can be used to adjust the tightness of the brake inner wire to achieve the desired bicycle hydraulic brake feel..
  • 【Upgrade Design】: HB-100 uses a new hydraulic line pull clamp technology. The block of the HB-100 mechanical disc brake caliper is equipped with built-in brake oil, and then the brake clamp is used to control the line pulling hydraulic brake of the hydraulic clamp. The cylinder of the clamp is built-in brake oil..
  • 【Application Bikes】: Lining Pulled Hydraulic Disc Brake Suitable for mountain E-Bike,bikes, road bikes and folding bikes, MTB, scooter, fat bike..
  • 【Note】: Please do not remove the yellow pad before installation, and pinch the brake lever, otherwise it will cause oil leakage or scrap the oil disc.
Check Stock

Mikuni Rs Series Carbs 40mm Rs40-D1-K

  • The Mikuni RS Series Carburetors were designed and built in response to the needs of the worlds top motorcycle road race and drag race teams..
  • They required carburetors which could satisfy the precise fuel metering demands and high flow volume required by highly modified race engines..
  • And yet, also provide the smooth, controllable throttle response that is needed by any rider pushing his motorcycle to its limits on the race track and under any high performance applications..
  • The carburetors need to meter fuel correctly under a wide range of atmospheric conditions and engine tuning modifications while being easily accessible for trackside tuning changes which need to be made quickly..
  • Designed for in-line four cylinder performance motorcycle applications, the Mikuni RS Series Radial Flat Slide Carburetors offer superior horsepower gains with their maximum flowing smoothbore induction tract and radial flat slide design..
Check Stock