Reviews Pi Camera Case

Infrared Night Vision IR Camera for Raspberry Pi 4 Pi 3b+ Video Webcam with Case Suits for 3D Printer

  • New design Acrylic holder case make sure your pi camera is more stable and flexible, the case reserve the hole for heat-sink, IR led and screws hole,....
  • Compatible with all series, fit for Raspberry pi 4, Pi 3 B+ with 100cm FFC Camera Cable, and match 30cm FPC Cable for Pi Zero, also can works with....
  • HD resolution, the night vision camera is capable of 2592*1944 pixel static images, and also supports 1080P 30fps, 720P 60fps and 640*480P 60/90fps....
  • Better low light performance, IR corrected lens to reduce focus shift at night, and IR LED illuminator to improve the lightning condition.
  • Typical usage scenarios, Home security and surveillance, motion detection, 3D printer observe, time-lapse photography and other Raspberry Pi camera....
Check Stock

Arducam 16MP Autofocus Quad-Camera Kit for Raspberry Pi, 16MP IMX519 Autofocus Synchronized Raspberry Pi Camera, Compatible with Nvidia Jetson Nano/Xavier NX

  • Designed for Raspberry Pi Camera: This Quad- Camera kit allows you to connect four 16MP IMX519 raspberry pi cameras to a single standard pi board and capture images or video at the same time..
  • Four in One: Combine four cameras into one frame, each with a resolution of 1/4.
  • the maximum output you can get: 4656 x 3496 for still images and 1920x1080 for video. Please note the frame rate for video and still images will drop to half the frame rate you would normally get with a single camera..
  • Wide compatibility: It is compatible with the latest Raspberry Pi camera software (libcamera) and uses the official Pi camera tuning algorithm. It also supports multi-platform multi-camera solutions such as Raspberry Pi, Jetson Nano, Xavier NX and many more. And this Camarray HAT is also compatible with Raspberry Pi 3 and Raspberry Pi (V1/V2/HQ) cameras..
  • Applications: Multiple camera processing technologies have enabled VR (Virtual Reality), AR(Augmented Reality), and other applications like SLAM (Simultaneous Localization and Mapping). Synchronized video streams with Raspberry Pi could be used for many use-cases (e.g., stitching, 3D sensing, tracking, …) before investing in an expensive video multiplexer hardware..
  • Please note: The cameras in the set are specifi....
Check Stock

Raspberry Pi HQ Camera Module with Case for Raspberry Pi 4B/3B+/3B/2B/A+/Zero/W/Zero WH,12.3MP IMX477 Sensor Support C- and CS-Mount Lenses, Alternative for Raspberry Pi Camera Module V2 (8 Items)

  • This Raspberry Pi High Quality Camera is the latest camera board from Raspberry Pi Foundation.It is compatible with All Raspberry Pi series boards (Raspberry Pi 4B/3B+/3B/2B/A+/Zero/Zero W/Zero WH,etc.).
  • Higher Resolution & Sensitivity Camera Module---Compared To 8MP Of Normal Raspberry Camera, The High Quality Camera Offers Up To 12.3MP, Along With Nearly 50% Greater Area Per Pixel, Delivering Better Imaging Effect..
  • It adopts the IMX477R sensor, and requires a C- or CS-mount lens to work..
  • It could be an ideal alternative for the Raspberry Pi Camera Module V2. It suits industrial and consumer applications like security camera, and other specialist optical devices which require higher level of visual fidelity..
  • Package Content: 1.Raspberry Pi High Quality Camera main unit. 2.C-CS adapter. 3.Dust cap. 4.FPC ribbon. 5.Screwdriver. 6.Packing box. 7.Raspberry Pi Zero V1.3 Camera Cable 15cm. 8.Raspberry Pi Camera Matching Case..
Check Stock

Miuzei Raspberry Pi 4 Case with Fan Cooling Pi 4 Case with 4 Pcs Aluminum Heat Sinks Pi 4B Case for Raspberry Pi 4 Model B -Black/Blue (Pi 4 Board Not Included)

  • Raspberry Pi 4 Case for Raspberry Pi 4 - Miuzei clear blue acrylic raspberry pi 4b case is specially designed for raspberry pi 4 modle b / 4 b, and perfect compatible with raspberry pi 4 /4b. assembly easy for beginners and amateur..
  • Raspberry Pi 4 Case With Fan - New Raspberry pi 4b case with a Silence DC 5V cooling fan and 4 pcs Aluminum heatsinks, cooling system keep your Raspberry pi 4 B cool quickly even the CPU under high load..
  • Raspberry Pi 4 Model B Case - acrylic pi 4 case won’t block the signal.the rubber feet on the bottom lid can provide a stable platform for raspberry pi 4 case so that it allows air to circulate on the bottom side of the board and avoid the screws scratching the desk surface..
  • Easy To Access All Ports - Miuzei raspberry pi 4 case fan can perfect Access to the USB-C Power Connector, Dual Micro HDMI, Audio/Video, USB and Ethernet Ports, GPIO Port, Camera Cable, and Access to the Micro SD Card..
  • Packaging Content & After -Sales - you will receive pi 4 clear blue case, 4 piecess raspberry pi heatsink, 35mm cool fan, 4 piecess rubber feet, screwdrive, awesome looking, it can make your pi looks cooler than others. if you encounter any problems, you can contact us at any time, and we will answer you..
Check Stock

Raspberry Pi Camera Module V2-8 Megapixel,1080p (RPI-CAM-V2 + 20"/500mm Flex Cable + Pi Zero Cable)

  • What Will You Get: An 8mp raspberry pi camera V2 with a 15cm original FFC cable, a 50cm FFC cable for model A and B, a 15cm FPC cable for pi zero & w and an acrylic case..
  • Sensor: 8 megapixel Sony IMX219, Max. resolution: 3280 (H) x 2464 (V).
  • Frame Rates: 1080p30, 720p60 and 640x480p90.
  • Recommended Power Supply: DC 5V, above 1.8A.
  • Typical Usage Scenarios: this tiny camera board can be used for monitoring Octoprint 3D Printer, Home security and surveillance, dashcam or other machine vision application. Please search ASIN: B09TNG4V55/B09TKYXZFG to get Raspberry Pi Camera ABS Case and Tripod Case Kit..
Check Stock

MakerFocus Raspberry Pi 3 Case Protective Case, Raspberry Pi 3.5 inch Display Case, with Mini Cooling Fan for Raspberry Pi 3B, 3B+,2B,2B+ Compatible with Raspberry Pi GPIO 3.5 inch Display

  • Installation instructions video: Please get the link from the product description below. PLZ NOTE: ★This case is not compatible with 3.5 Inch HDMI TFT LCD Display, It is designed to RPI 3.5 Inch GPIO Display, ★The 3.5 inch screen is not included!!!.
  • Dual-use: You can use it only on the Raspberry Pi motherboard, or use it on the Raspberry Pi motherboard and Raspberry Pi 3.5inch display,Then decide whether to cover the its cover. (Note: The Raspberry Pi motherboard and Raspberry Pi 3.5inch display are not included!!!).
  • Can install mini cooling fan: The case when used without the display screen, you can install mini cooling fan, Snap-in installation, the cooling fan was included in packaging..
  • With GPIO open position: There is a GPIO open position on this case cover,when you use it only with Raspberry Pi motherboard, it can easy to pull up and insert the GPIO pins, don't need to open the cover. This case is easy to install and has good ventilation..
  • With cable guide hole: It reserved cable guide hole for the camera, more convenient to use with camera.
Check Stock

Arducam Raspberry Pi Camera Module 3 Wide, 120°(D) IMX708 Autofocus Pi Camera V3 with Acrylic Case, 15cm 15-22 Pin FFC Cable

  • Compatible with all Raspberry Pi boards: Raspberry pi camera v3 works with all Raspberry Pi models, 4B/3B, Pi Zero W/2 W..
  • Based on IMX708 sensor with HDR, 4608 x 2592 is the highest resolution you can get for still images, 1080p50 max for video..
  • The autofocus of pi cam v3 is achieved by a mixture of PDAF and CDAF, ensuring crisp and clear images..
  • Fully support libcamera and Picamera2, and uses CSI-2 serial data output with 2-wire serial communication for seamless integration..
  • Come with a 15cm 15-22pin camera cable, especially for Raspberry Pi zero 2 w.
  • also an acrylic camera case included, easily mount on any tripod with 1/4"-20 mounting screws..
Check Stock

Premium Raspberry PI 2 Model B Quad Core Case (White) Access to All Ports

  • This is a no-nonsense protective case designed specifically for the Raspberry Pi 2 Model B.
  • The case is a two-piece injection-moulded ABS enclosure that snaps together around the Raspberry Pi Model B+..
  • It provides the best available protection/accessibility for the Raspberry Pi 2 Model B.
  • Wall Mountable. Access to all PI consumer ports and GSI, camera and GPIO connectors..
Check Stock

Eleduino Raspberry Pi 3, 2 and B+ Case Aluminum with Fan (Black)

  • Aluminum case ,Customize for Raspberry Pi 3/Raspberry Pi 2/ Raspberry Pi B+.
  • High dimensional accuracy, surface anodic oxidation process. Durable, good heat dissipation.
  • Good ventilation,easy carrying Simply Clicks Together Enclosure,good heat dissipation.
  • Smart design，not block the wifi/BT signals.
  • Access to all Raspberry Pi 3 /Raspberry Pi 2 / Raspberry Pi B+ consumer ports and GSI, camera and GPIO connectors.
Check Stock

Arducam IMX519 Autofocus Camera Module for Raspberry Pi, 16MP AF Raspberry Pi Camera Compatible with Raspberry Pi 4B/3B+, Raspberry Pi Zero 2 W

  • 16 Megapixel: 2 times higher resolution than the Raspberry Pi camera V2. Unlike the native Pi camera, this camera requires some simple script configuration before use and does not support raspbian..
  • Autofocus: most versatile AF (Manual/Continuous/etc.) experience on a Pi camera..
  • Sharper Images/videos: Higher quality than the HQ camera..
  • V1/V2 Size: hassle-free upgrades to your existing projects..
  • Package Contents: The package includes an IMX519 CMOS camera board with an autofocus lens and a 15cm FPC cable. Please search ASIN: B09TSDZ48F for the camera extension kit, which allows you to place cameras up to 15 meters away for shooting. For the camera case and tripod set, please search ASIN: B09TKYXZFG..
Check Stock

JUN-ELECTRON for Raspberry Pi 4 Camera with Acrylic Holder Case Infrared Night Vision 5M 1080p Video Webcam Compatible Suit for Raspberry Pi 3 B+/Pi 3/Pi Zero

  • Compatible with all series, fit for Raspberry pi 4 / 3 B+ with 200cm FFC Camera Cable, and match 50cm FPC Cable for Pi Zero, also can works with your....
  • New Design Acrylic Case can hold camera make it works more stable, the case reserve the hole for heat-sink, IR led and screws hole, Easy to adjust the....
  • Better low light performance, IR corrected lens to reduce focus shift at night, and IR LED illuminator to improve the lightning condition.
  • HD resolution, the night vision camera is capable of 2592*1944 pixel static images, and also supports 1080P 30fps, 720P 60fps and 640*480P 60/90fps....
  • Typical usage scenarios, Home security and surveillance, motion detection, 3D printer observe, time-lapse photography and other Raspberry Pi camera....
Check Stock

5MP 1080P Video Camera Module for Raspberry Pi 4 Model B Pi 3 b+ Pi Zero W Camera with Case Flex Cable Camera + Holder

  • Compatible with Raspberry Pi 4 Model B, Pi 3 Model b+, Pi 3b, Pi Zero, Pi Zero Wireless.
  • 5 Megapixels sensor with OV5647 webcam sensor in a fixed-focus lens.
  • The camera is capable of 2592 x 1944 pixel static images,and also supports 1080p/30 fps, 720p/ 60fps and 640 x480p 60/90 video recording.
  • Specially design clear acrylic case to protect camera module. Easy to install with detail assembly instruction.
  • High Quality Service -- Using the high quality and sturdy package to ship the product. Get more technique support? The professional customer service....
Check Stock

Arducam 5MP Camera for Raspberry Pi, 1080P HD OV5647 Camera Module V1 for Pi 4, Raspberry Pi 3, 3B+, and Other A/B Series

  • High-Definition video camera for Raspberry Pi Model A or B, B+, model 2, Raspberry Pi 3,3 B+, Pi 4(NOT for Pi Zero).
  • 5MPixel sensor with Omnivision OV5647 sensor in a fixed-focus lens. Software auto focus lens: B07SN8GYGD.
  • Check ASIN: B07RWCGX5K for OV5647 with acrylic case. Other optional accessories: ABS case (B09TNG4V55).
Check Stock