ACCEL 49505 SuperTuner - Handheld Computer Programmer
- Brand New Driveshaft Propeller Shaft CV Joint Repair Kit.
- This Kit Repairs the Front Shaft, Transfer Case Side (This front driveshaft cv joint ONLY FITS to driveshafts with one cv joint and one universal joint. It does not fit to shafts with cv joints on both ends.).
- See Compatibility Chart To Verify Your Specific Vehicle Year, Make, & Model.
- Replaces 52105728AD, 52105758AD, P52853431AA, P52853432AA.
Check StockWiha 32698 Pliers and Cutter Set, 3 Piece
- Made from high quality forged CV tool steels.
- Soft vinyl grip handles are oil and solvent resistant.
Check StockABN Inner CV Axle Removal Tool - CV Axle Puller Slide Hammer Set with 5 lb Slide Hammer and CV Joint Puller Adapter
- [Remove Front Wheel Drive Axles Easily] To replace or repair your CV axle joints easily, use the ABN FWD Axle Puller Slide Hammer Puller Set.
- The CV joint puller adapter and large slide hammer bearing puller allow you to create added torque to loosen and remove stubborn axle shafts and water pumps.
- [Fits Your Needs] Chrome-plated 23 x 5/8-inch hammer bar features a 5/8-inch x 18 threaded section to fit your adapters, while the slide hammer CV axle adapter has 48mm (roughly 2-inch) opening and a 2.5-inch depth to fit your needs.
- [Easy to Use] Attach the inner CV axle puller to your axle slide hammer then position the adapter around the shaft behind the inner boot.
- Slide the 5 lb hammer weight back and forth to create torque to pull out the axle.
- Use lubricant fluid for added ease (not included).
- [Safe for Your Vehicle] Slide hammer CV joint puller and attachment design focuses the added torque to the back of the housing to prevent damage to the roller bearing inside the joint.
- Pulls CV joints on 1986-current Taurus/Sable.
- [Built to Last] Hardened hammer shaft provides strength and d....
Check StockDetroit Axle - 4WD 8-Lug Front Axle + Wheel Hub Bearing + Upper Control Arm Ball Joints Suspension Kit Replacement for Silverado Sierra 2500 HD 3500 Hummer H2
- Fits: Specific Models - Check Fitment Chart and Product Description for Accurate Information.
- Kit Includes: 2x Front CV Axle Drive Shaft + 2x Front Wheel Hub & Bearings + 2x Upper Control Arm w/ Ball Joints + 2x Lower Ball Joints +2x Sway Bars + 4x Inner and Outer Tie Rods + 2x Idler Arm & Pitman Arm + 1x Idler Arm Bracket.
- Hub Specifications: Position: Front Left and Right | Drive: 4WD | Lugs: 8 Bolts | ABS Type: Sensor Wire | Flange: 4-Bolt Square.
Check StockEar Type CV Joint Boot Clamp Plier
- Performance Tool Ear Type CV Joint Boot Clamp Pliers (W83013).
- For all ear-type clamps including GM FWD outboard CV joints..
- Ideal for installing clamps fuel filters.
- Great for CV joint boots and other cooling system hoses.
- Heavy duty steel and no-slip grip construction.
Check StockStainless Steel Universal Adjustable AXLE CV Joint Boot Crimp Clamp Kit,24PCS 12pcs Small+ 12pcs Large
- HIGH QUALITY: The cv boot clamps is made of non-magnetic 304 stainless steel for long durability and reliability..
- APPLICATION: It can be used on drive & CV Axle. A perfect replacement for your car broken drive shaft CV boot clamp..
- Size: Large-Width: 0.352" (8.95mm),Thickness: 0.033" (0.85mm), Small-Width: 0.273" (6.94mm),Thickness: 0.023" (0.58mm)..
- Easy Installation: Easy to Install. Suitable for left , right, front and rear CV joints on most cars and light commercial vehicles..
- WHAT YOU'LL GET: 12 Pcs Small CV Boot Clamps+ 12 Pcs Large CV Boot Clamps, Place order with 100% confidence, we provide 1 click refund for our valued....
Check StockOMT Inner CV Axle Puller Tool Set with 5/8"-18 Slide Hammer & Adapter | Inner CV Joint Removal Tool Kit | Front Wheel Drive Axle Puller Set Compatible with Taurus Sable FWDs from 1986 to 2021
- PULL CV JOINTS & AXLES: This CV joint puller tool set by Orion Motor Tech is compatible with Ford Taurus and Mercury Sable models from 1986 to present, loosening and removing their front wheel drive axles and hidden retaining rings in minutes.
- MULTIPURPOSE SLIDE HAMMER: Our slide hammer weighs 7 pounds for extra strength to give you a straight and even pull for damage-free removal of the axle assembly.
- its threading also lets you use it with other 5/8"-18 adapters to deal with other makes and models or to handle other work around your engine.
- DURABLE PULLER ADAPTER: The U-shaped CV joint fork has a 2-inch opening and 2.4-inch depth to firmly lock onto your Sable or Taurus axle assembly, making removal of stuck CV joints a cinch.
- QUICK & EASY OPERATION: These automotive tools work together to provide straight and even force so your constant velocity axle pops out smoothly, leaving the roller bearing inside the joint and the rest of your vehicle untouched.
- BUILT TO LAST: Made of premium AISI 1045 medium carbon steel, our CV joint removal set provides strong and dependabl....
Check StockSixity 2003-2008 for Yamaha 660 Grizzly 4X4 Rear Left Axles Back Driver YRM660FGHX GX Complete Side
- Note: YRM660FGHX GX. INSTALL FAST, RIDE FAST: Sixity XTA Axles arrive fully assembled including inboard and outboard universal CV joints for quick installation.
- TAP INTO THE POWER OF CHROME-MOLY: chrome-moly is a steel alloy made of chromium (the hardest metal on the Mohs scale) and molybdenum. At 200 percent stronger than standard 1020 stainless steel, and 92 percent stronger than 4130 chrome-moly, the 4340 chrome-moly steel bar showcases high strength-to-weight ratio, exceptional tensile strength, and formidable impact resistance in order to withstand extreme levels of torque and ensure durability through the roughest terrain.
- RIDE WITH OFF-ROAD-TOUGH CV JOINTS: the heavy-gauge neoprene boots are made of an elastic compound much more difficult to puncture than rubber, and they vastly outperform thermoplastic boots in flexibility and environmental protection, delivering abrasion resistance, longer wear life, and oil/grease resistance.
- PUT IT TO THE TEST: recommended for intense mudders, the Sixity XTA axles feature induction heat-treated bearings that reduce friction and increase CV-joint strength and durability. High-temperature and high-load-bearing moly grease packed into the boot helps to ensure long-lasting CV-joint life.
Check StockSixity 2003-2008 for Yamaha 660 Grizzly 4X4 Rear Right Axles Back Passenger YRM660FGHX GX Complete Side
- Note: YRM660FGHX GX. INSTALL FAST, RIDE FAST: Sixity XTA Axles arrive fully assembled including inboard and outboard universal CV joints for quick installation.
- TAP INTO THE POWER OF CHROME-MOLY: chrome-moly is a steel alloy made of chromium (the hardest metal on the Mohs scale) and molybdenum. At 200 percent stronger than standard 1020 stainless steel, and 92 percent stronger than 4130 chrome-moly, the 4340 chrome-moly steel bar showcases high strength-to-weight ratio, exceptional tensile strength, and formidable impact resistance in order to withstand extreme levels of torque and ensure durability through the roughest terrain.
- RIDE WITH OFF-ROAD-TOUGH CV JOINTS: the heavy-gauge neoprene boots are made of an elastic compound much more difficult to puncture than rubber, and they vastly outperform thermoplastic boots in flexibility and environmental protection, delivering abrasion resistance, longer wear life, and oil/grease resistance.
- PUT IT TO THE TEST: recommended for intense mudders, the Sixity XTA axles feature induction heat-treated bearings that reduce friction and increase CV-joint strength and durability. High-temperature and high-load-bearing moly grease packed into the boot helps to ensure long-lasting CV-joint life.
Check StockApplianPar Pack of 3 Angle Grinder Metal Outer Flange Lock Nut 5/8-11 for Dewalt Milwaukee Makita Black & Decker
- Fit models: Angle Grinder 9029, 9069, 9016DB, 9047L, 9558NB, 9557PB, GA5020 10.5A 5", 9565PC, 9554NB, GA4530 4-1/2", 9015A, GA7021, GA9040S 9" 15A,GA5010Z 10.5A 5",9564PC 4-1/2", 9557NB, 9558PB, GA6020 6", 9005B, 9503BH, 9524NB, 9528PB, 9528NB, 9565CV, 9564CV,9005BZ, 9015B, 9505BH, 9527PB, 9527NB, 9015DB, 9561CV, 9016B, 9049, 9067L, 9077SL, 9564.
- Replaces part numbers: 224399-1, 193465-4, 224568-4.
- Outer Nut Size: 5/8"-11,fits all 4-1/2",5" and 7" grinders.
- Package includes: 3 x Outer angle grinder flange.
Check StockUniversal Standard CV Boot & Cone Kit Stretchy Drive Shaft Boot Fitting Tool
- Made of high quality plastic material, durable and practical to use.
Check StockPodoy Angle Grinder Outer Lock Nut for Compatible with Makita Dewalt Milwaukee Bosch Black & Decker Ryobi 5/8 -11 Fits All 4-1/2 4 Pack
- For Compatible with Makita:Angle Grinder 9565CV Angle Grinder 9564CV Angle Grinder 9029 Grinder 9069 Angle Grinder 9016DB Angle Grinder 9047L Angle....
- For Compatible with Makita: 9005BZ Grinder 9015B Grinder 9505BH Grinder 9527PB Grinder 9527NB Angle Grinder 9015DB Angle Grinder 9561CV Angle Grinder....
- For Compatible with Makita 224399-1, 193465-4, 224568-4 parts. Compatible List is provided below for reference,Outer Nut Size: 5/8"-11,fits all....
- Package include :4 pcs outer angle grinder flange nuts.
- Non original aftermarket part,The part/product is not sponsored or endorsed by,or affiliated with the brands it fit,including Makita Dewalt Milwaukee....
Check StockYuangTow Universal Stretch CV Boot Tool Installation Mount Cone for Fitting Boots With A Smooth Surface Cars Accessories Plastic Auto Replacement Parts, 1 PCS, Black, 13.07 x 4.84 4.37 inches
- ★Function:Universal fit CV boot air tool,Sure makes changing CV boots on 4 wheelers very easy as you don't have to disassemble joint,saves a lot of time when replacing outer CV boots..
- ★Material:CV removal tool made of high quality steel,rust proof, and strong toughness to ensure durability and reliability.
- ★Multipurpose:CV boot tool can be used for Vtt,Toyota Corolla,Audi,BMW,saves time and labor easy to use anyone with UTV OR ATV will find this product great..
- ★Design: Simple one button operation expands the CV boot in seconds to fit the CV joint and can be supplied separately or used with CV dust boot, grease and clamp.
- ★We are specialized in producing various tools, please go find all kinds of tools fittings you need in LAJIAOZ store .Customer satisfaction is our top priority,if there anything missed or broken,pls let us know,we'll reply within 24 hours.
Check Stock