Reviews Oil retaining Bearings

Riedell UPTOWN 120 BR Mens Rhythm Skates 2009 - Size 5

  • TOP QUALITY CRAFTSMANSHIP - These precision bearings come equipped with hardened Swiss chromium steel alloy balls that can endure long-lasting use..
  • OPTIMIZED DURABILITY - The KwiK Swiss Nitride bearings use a Titanium Nitride coating. This coating does not chip, flake, or degrade during prolonged rough use..
  • CORROSION RESISTANT DESIGN - The KwiK bearings' Titanium Nitride-coated races resist corrosion. They also provide strength and smoothness to create a performance with the greatest roll..
  • FRICTION RESISTANT RETAINERS - These bearings come equipped with friction resistant Delrin retainers that are pre-spun with high-performance oil..
  • SLEEK & LUXURIOUS DESIGN - The 8mm skate bearings come with a metallic gold finish, a design that is worthy of its performance. This product is not a children's product and is not designed or intended for use by children 12 years of age or younger..
Check Stock

2 Scooter Wheels With Abec 7 Bearings for RAZOR SCOOTER 100mm (blue)

  • High-performance, high-rebound scooter wheels which fit on most scooters and measure 100mm in diameter (standard 24mm width). These replacement wheels will have your scooter riding like its brand new!.
  • These wheels utilize a specialized outdoor urethane formula (88A Durometer) for longevity and durability while providing a smooth and comfortable ride.
  • The Rounded Profile and Super High Rebound Urethane creates less friction allowing for faster speeds and better control.
  • Making a great bearing starts with having a lot of expertise, and using the best materials. Bullseye uses super hard Chrome Steel balls that measure 65 on the Rockwell Scale.
  • each ball is tested to ensure that is perfectly round. The balls run in deep-grove race ways, and are retained by a self-lubricating Delrin crown. A low viscosity synthetic oil has been added to make these bearings spin great, while keeping friction levels at a minimum.
  • Includes 2 wheels with Abec 7 bearings installed. These are easy to replace on any scooter!.
Check Stock

2 Scooter Wheels With Abec 7 Bearings for RAZOR SCOOTER 100mm (red)

  • High-performance, high-rebound scooter wheels which fit on most scooters and measure 100mm in diameter (standard 24mm width). These replacement wheels will have your scooter riding like its brand new!.
  • These wheels utilize a specialized outdoor urethane formula (88A Durometer) for longevity and durability while providing a smooth and comfortable ride.
  • The Rounded Profile and Super High Rebound Urethane creates less friction allowing for faster speeds and better control.
  • Making a great bearing starts with having a lot of expertise, and using the best materials. Bullseye uses super hard Chrome Steel balls that measure 65 on the Rockwell Scale.
  • each ball is tested to ensure that is perfectly round. The balls run in deep-grove race ways, and are retained by a self-lubricating Delrin crown. A low viscosity synthetic oil has been added to make these bearings spin great, while keeping friction levels at a minimum.
  • Includes 2 wheels with Abec 7 bearings installed. These are easy to replace on any scooter!.
Check Stock

Replacement Razor Scooter Wheels, Abec 7 Bearings, Handle Bar Grips (Blue/Blue)

  • This pack contains everything you need to upgrade your scooter!! Wheels, bearings, and handlebar grips will have your scooter riding like new again!.
  • High-performance, high-rebound scooter wheels which fit on most scooters and measure 100mm in diameter (standard 24mm width). These wheels utilize a specialized outdoor urethane formula (88A Durometer) for longevity and durability while providing a smooth and comfortable ride.
  • Having a good grip on your ride is key for maximum control and comfort. Kick Push offers a dense foam grip that is soft, comfortable, and long-lasting! These grips are made with non-bleeding colors. These measure 4� long with a 7/8� center hole, meaning they fit on 7/8� bars. These are compatible with virtually every scooter! These also include plastic end caps which provide extra protection to both your bars and your grips in case of wipeouts.
  • Making a great bearing starts with having a lot of expertise, and using the best materials. Bullseye uses super hard Chrome Steel balls that measure 65 on the Rockwell Scale.
  • each ball is tested to ensure that is perfectly round. The balls run in deep-grove race ways, and are retained by a self-lubricating Delrin crown. A low viscosity synthetic oil has been added to make these....
Check Stock

TGM Skateboards Replacement Razor Scooter Wheels, ABEC 7 Bearings, Handle Bar Grips (Clear/Black)

  • This pack contains everything you need to upgrade your scooter!! Wheels, bearings, and handlebar grips will have your scooter riding like new again!.
  • High-performance, high-rebound scooter wheels which fit on most scooters and measure 100mm in diameter (standard 24mm width). These wheels utilize a specialized outdoor urethane formula (88A Durometer) for longevity and durability while providing a smooth and comfortable ride.
  • Having a good grip on your ride is key for maximum control and comfort. Kick Push offers a dense foam grip that is soft, comfortable, and long-lasting! These grips are made with non-bleeding colors. These measure 4� long with a 7/8� center hole, meaning they fit on 7/8� bars. These are compatible with virtually every scooter! These also include plastic end caps which provide extra protection to both your bars and your grips in case of wipeouts.
  • Making a great bearing starts with having a lot of expertise, and using the best materials. Bullseye uses super hard Chrome Steel balls that measure 65 on the Rockwell Scale.
  • each ball is tested to ensure that is perfectly round. The balls run in deep-grove race ways, and are retained by a self-lubricating Delrin crown. A low viscosity synthetic oil has been added to make these....
Check Stock

TORCO A550055KE MPZ Engine Assembly Lube - 12 oz. Bottle

  • MPZ engine assembly lube is favored by professional mechanics for assembling many internal mechanical components including wrist pins, pistons, bushings, plain bearings, ball bearings, roller bearings, journals and transmission components.
  • MPZ EAL is a high viscosity, oil soluble lubricant which contains a concentrate of anti-wear, anti-friction and anti-shock chemistries featuring the highest degree of protection.
  • Completely oil soluble increases protection during break-in with excellent adhesion properties and will slowly run and drip leaving protective film on treated part.
  • Protects assembled engines, transmissions and rear axles from rust and corrosion during storage and shipment to vehicle assembly plants.
  • Recommended as a pre-lube for valve train parts, wrist pins, rod bearings, main bearings, gears, bushings, roller bearings, ball bearings in manual and automatic transmissions, transaxles, transfer cases, rear axles and marine v-drives.
Check Stock

INA NATR15 Bearing Track Roller, 35X18X15 MM

  • Track roller with needle bearings supports high static and dynamic loads in track-type applications.
  • Full complement of bearings for higher radial load capacity than caged bearings.
  • Yoke-type rollers for use with heavier loads or where clevis mounting is preferred.
  • Thick outer ring helps minimize deformation under bending stresses.
  • Rubber seals to retain lubricant and for protection against contaminants.
Check Stock

MAHLE Original 41940.030 Ford 6.0L Power Stroke & Navistar VT275/365 & MaxxForce 5 0.030\ Piston Ring Set, 8 Pack

  • THIS KIT INCLUDES: Piston Set, Piston Ring Set, Main Bearings Set, Rod Bearings Set, Head Gasket Set, Lower Gasket Set, Freeze Plug Set (Brass), Cam Bearings, Timing Chain Kit, Oil Pump.
  • FITS: 87-90 Cadillac, Chevrolet, Pontiac / Brougham, Camaro, Caprice, Firebird 5.7L V8 OHV Naturally Aspirated.
  • FITMENT NOTES: w/ Oil Pump & Timing Belt Or Timing Kit If Applicable, Dish Pistons, Master Kit, w/ 3/4 Inlet Pump, w/ 3/4 Inlet, w/o IG3173, w/ Oil Pump & Timing Belt Or Timing Kit If Applica.
  • You are assured to receive a worldwide proven Master Engine Rebuild Kit quality part with OE quality fit and performance..
  • IMPORTANT: This Engine Kit is in STANDARD SIZE in all of its components. If you need oversized Pistons, Piston Rings, Rod Bearings or Main Bearings, send us a message prior ordering, indicating the correct size you need, so our customer service team can confirm availability. If we do not receive communication from you, everything will be sent in STANDARD SIZE by default.
Check Stock

VEVOR Carrier & Pinion Bearing Puller Compatible with Dana 30,40,50,60,70, 80, Ford 10.25  Bearings Pinion Puller Tool with 3 Clamshells 45# Steel Clamshell Bearing Puller for Auto Repair

  • Great Compatibility: The clamshell carrier bearing puller is compatible with Dana 30, 40, 60, 70, Ford 10.25" bearings. With the clamshell bearing puller, you can quickly remove the bearings. In addition, its power is evenly distributed, so less damage will be brought to your pinion bearings..
  • Premium Performance & Features: With high working efficiency, this carrier pinion bearing puller can effortlessly remove the pinion bearings with minor damage, drastically reducing dismantled time. And the carrier bearing puller will no longer easily pry into the pinion's sealing surface..
  • Complete Equipment: All necessary parts are ready for you. There is a main puller body, plug, center bolt, 3 clamshells, retaining ring, and adjuster rings. Besides, this unit comes with a handy stand, so you can group all the working parts together..
  • Easy to Operate: There is no need for other complex working tools. Firstly, place the main body over the plug and adjust the lower and upper adjusting ring. Secondly, select a proper clamshell and tighten the retaining ring. Finally, you can use an impact gun to remove the bearing..
  • Superior Material: The clamshell bearing tool is made of durable 45# steel, providing good performance in withstanding abrasion, corrosion, and impa....
Check Stock

Chaoyue Skateboard Bearings 608-2Rs (Pack of 8) Made of Gcr15, with High Precision, Fast Speed and Low Sound

  • Bones Reds are manufactured to Bones Skate Rated specifications in a manufacturing facility dedicated to producing the highest quality skate bearings. They are inspected twice before being shipped to skaters and offer the greatest combination of performance, durability and low cost in the industry..
  • Single, non-contact, removable rubber shield for easy cleaning and less friction. High speed Nylon ball retainer for greater strength and speed. Pre-lubricated with Speed Cream racing lubricant. Skate Rated clearances, tolerances, materials and lubricant provide the best performance and durability possible..
  • Includes a set of 8 Bones Reds Bearings, 8 Speed Washers, and 4 Bearing Spacers..
  • Instructions and Sticker are included in the box of Bones Reds Bearings..
  • Bones Reds Bearings fit all skateboard wheels. This package includes enough bearings to outfit 1 set of 4 skateboard wheels..
Check Stock

Amphetamine HIGH Performance Inline Skate Ceramic Hybrid Bearings

  • SPEED - Amphetamine Hybrid Ceramic bearings are capable of high speeds with a high level of durability and longevity at a fraction of the cost..
  • CONSTRUCTION - Hybrid Ceramic bearings feature 1 ceramic ball and 6 precision steel balls. The single ceramic ball pulverizes dirt which keeps bearings clean. The single ceramic ball keeps cost down compared to full ceramic bearings..
  • FEATURES - Hybrid Ceramic bearings offer the durability of a steel bearing with the speed of a ceramic bearing. Hybrid bearings offer performance on a budget..
  • PRE-LUBRICATED - Amphetamine bearings are pre-lubricated with Amp Synthetic Speed Oil and are ready to provide high speeds straight out of the package..
  • INCLUDES - 16 Bearings which is enough for 8 wheels. These bearings are size 608, which has a 22mm OD (Outer Diameter) and 8mm ID (Inner Diamter/Opening Hole Size)..
Check Stock

Zealous Bearings for Skateboards and Longboards (Steel)

  • Eight-pack of premium ceramic skateboard wheel bearings with four bearing spacers, instructions, and a sticker.
  • Cerbec ceramic balls are light, hard, and strong for a long lasting performance.
  • Precision-grade Swiss design and manufacturing acclaimed for 25 years.
  • Nylon ball retainers and Bones Speed Cream lubricant for a sustained ride.
  • Skate Rated for better performance than any ABEC rated bearings.
  • lifetime warranty against manufacturing defects.
Check Stock

MakerHawk 2pcs Brushless DC Cooling Fan 40mm x 40mm x 10mm 4010 12V 0.08A 3D Printer Fan Hydraulic Turbo Cooling Fan with XH2.54-2P Wire for 3D Printer

  • Hydraulic bearings are based on oil-impregnated bearings. Hydraulic bearings have a larger oil storage space than oil-impregnated bearings and have a unique loop-back oil supply circuit..
  • Super Quiet: This fan will not make you feel uneasy during they are working, but also a quiet experiment environment for you..
  • Air Flow: 2.8CFM Dimensions: 40 x 40 x 10mm(1.6 x 1.6 x 0.36inch).
  • Connector: 2 Terminal Connector with 2pin-ph2.54.
  • Wiring: red wire is connected to positive pole, black wire is connected to negative pole.
  • We Have a Strong After-sales Service Team: As long as you have any questions about the product, we will resolve your issue immediately if received your email, your satisfactory purchase experience is our greatest hope! How to email us? Please click "MakerHawk-US" and click "Ask a question" to email us! Looking forward to your consultation!.
Check Stock