Reviews Masonry Anchor

Nylon Hammer Drive Pin Nail in Masonry Concrete Anchors Zinc Nail 1/4 x 1 Qty 100

  • 1/4 inch Diameter Nylon Mushroom Head Nail In Masonry Anchors with Zinc Plated Steel Nails.
  • Using a pre-drilled hole, they are installed with hand tools (typically a hammer).
  • Drive the pin into the anchor body, expanding the anchor, to form a tight fit.
  • Rust resistant nylon and zinc plated nail.
  • Designed for light duty masonry applications.
Check Stock

3/8\ x 2 1/2\ Lag Screw Expansion Shield Long Zinc Alloy Pk 300

  • Expansion shield anchor works with a lag screw to provide a secure hold in most materials including solid masonry, masonry joints, and uncracked concrete.
  • Anchor has an internally threaded body made of zamac alloy.
  • Meets Fed. Spec. GSA FFS-325C Group 2, Type 1, Class 2C specifications.
  • Ultimate tensile strength 420 lb. in 2,000-psi concrete.
  • Use one-fourth or less of listed maximum values for safe working loads (as required by local regulations).
Check Stock

TEACH Flat Head Phillips Drive Concrete Screw to Anchor Masonry, Block & Brick,270-Piece

  • Concrete Screw Flange 5/8" Head (depending on the length, it will be either full or partial threaded). The diamond tip allows for superior penetriating into hard materials. Great for anchoring items to concrete, brick, block, or other masonry materials. Ceramic coating exceeds 500/hrs salt spray resistance.
  • An externally threaded, hardened screw with a double lead, consisting of alternating raised and lowered threads with notches cut into the raised threads, and a diamond-shaped, nail-type point. Cuts its own threads and when used in concrete, block or brick. Eliminates the need for an anchor when used in light or medium-duty applications. When used in concrete, it can be removed and re-driven into the same hole. Special carbide bits are recommended for driving concrete screws into masonry..
  • Some applications include anchoring the following to masonry: electrical junction boxes, wooden beams, plywood, exterior insulation, metal flashing, thresholds. Hole should be of a depth equal to the required embedment plus 1/2”.
  • Concrete screws should be installed a minimum of ten anchor diameters between each other. They have an advantage over most other types of masonry anchors in that they can be installed close to the edge of t....
Check Stock

Hurricane Hardware Stainless Steel Phillips Combo Drive Stainless Steel Sidewalk Bolt Kit with Masonry Anchors & Set Tool - 49 Pieces

  • 1/4"-20 x 1-1/2" Phillips Slotted Combo Drive Sidewalk Bolts 18-8 Stainless Steel - 24 pieces.
  • 1/4"-20 Machine Screw Masonry Anchors - 24 Pieces.
  • Includes Setting Tool for Proper Machine Screw Anchor Installation.
  • Commonly used for storm windows and shutters to anchor into brick or masonry wall.
  • Fixtures can be removed or replaced without sacrificing holding power.
Check Stock

Shorpioen 100-Pack 1/4 x 1-3/4 Concrete Screw Hex Flanged White No Drill Bit BC-1428CNHFW

  • Building Code Approved. The diamond tip allows for superior penetriating into hard materials. Great for anchoring items to concrete, brick, block, or other masonry materials. Blue ceramic coating exceeds 500/hrs salt spray resistance.
  • An externally threaded, hardened screw with a double lead, consisting of alternating raised and lowered threads with notches cut into the raised threads, and a diamond-shaped, nail-type point. Cuts its own threads and when used in concrete, block or brick. Eliminates the need for an anchor when used in light or medium-duty applications. When used in concrete, it can be removed and re-driven into the same hole. Special carbide bits are recommended for driving concrete screws into masonry..
  • Some applications include anchoring the following to masonry: electrical junction boxes, wooden beams, plywood, exterior insulation, metal flashing, thresholds. The Ruspert finish is a ceramic coating that also allows these fasteners to be used in pressure-treated lumber. Hole should be of a depth equal to the required embedment plus 1/2”.
  • The Ruspert finish is a ceramic coating that also allows these fasteners to be used in pressure-treated lumber. Check the Item Description to see if a drill is included as well..
Check Stock

50 Pcs 3/8 x 3 Zinc Plated Concrete Anchors Masonry Screws Heavy Duty Carbon Steel Concrete Anchors and Screws Kit Hex Head Large Diameter Concrete Anchor Bolts for Brick Blocks Cement

  • Adequate Quantity: there are 50 pieces of concrete anchors, suitable for large volume work, meeting your daily needs, and can also be shared with your family and friends.
  • Pocket Size: each of concrete screws and anchors is about 3/8" x 3", and weighs only 1.3 ounce/ 37 g, fine workmanship, and easy to carry around, providing you with much convenience.
  • Quality and Sturdy Material: hex concrete anchors are made of carbon steel, with galvanized surface to resist rust, and feature higher hardness, hard and not easy to deform, especially practical for dry environment.
  • Novel Design: featuring low torque threads, masonry screws have deep and clear threads, which can make concrete penetration easily, and also simple to install.
  • The anchor has a finished hex washer head with anti rotation serrations to keep the anchor away from backing out.
  • Wide Range of Applications: hex head concrete screw anchor is mainly designed for concrete, masonry, brick or block.
  • Note that using a standard drill bit for installation, the drill bit size is the same as the anchor diameter.
Check Stock

M10 x 80mm External Hex Expansion Bolts Screws, Hex Head Sleeve Anchor, 304 Stainless Steel, 4Pcs

  • M10 x 80mm Expansion Bolts, Thread Diameter: 10mm/ 0.4'', Expansion Tube Diameter: 12mm/ 0.47'', Total Length: 80mm/ 3.14''..
  • Made of 304 stainless steel, durable and rust resistant..
  • Concrete and masonry anchors, easy to install..
  • Used for heavy duty fixing of concrete masonry and solid masonry, ceiling and expansion sleeve anchor bolts..
  • Package Included: 4Pcs M10 x 80 expansion bolts..
Check Stock

CONFAST 3/8\ Lag Shield Anchor Long (12 per Box)

  • Expansion shield anchor provides a secure hold in most materials including solid masonry and uncracked concrete, even in applications where the anchor will be exposed to side pressure or vibration.
  • Anchor is made of rust-resistant zamac alloy and consists of cone on each side that expands the surrounding sleeve when a threaded machine bolt is inserted, gripping the mounting material and holding the anchor in place.
  • Meets Fed. Spec. GSA FFS-325 Group II Type 2 Class 2 Style 2 specifications.
  • Ultimate tensile strength is 1,190 lb. in 2,000-psi concrete.
  • Use one-fourth or less of listed maximum values for safe working loads (as required by local regulations).
Check Stock

Dewalt DT6952-QZ Masonry Drill bit-Set (5 Piece)

  • Typically used for drilling anchor, plastic plug, fixing or pipework clearance holes.
  • Rotary/percussion masonry drill bit 130° douglas form Carbide tip.
  • Suitable for masonry, brick/blockwork, stone.
Check Stock

1/4 Tapcon Style Concrete Screws Slotted Hex Washer Head Concrete Screws to Anchor Masonry Block & Brick 1/4 x 1-3/4 Qty 1000

  • Slotted Hex Washer Head Masonry Screws - 1/4 inch Diameter.
  • Commonly used to anchor fixtures to brick, block or concrete.
  • Blue Climaseal Coating for Corrosion Resistance & Durability.
  • Cuts its own threads into concrete and other masonry materials.
  • Does not include masonry bit for pilot hole.
Check Stock

3/16 Tapcon Style Concrete Screws Slotted Hex Washer Head Concrete Screws to Anchor Masonry Block & Brick 3/16 x 1-1/4 Qty 1000

  • Slotted Hex Washer Head Masonry Screws - 3/16 inch Diameter.
  • Commonly used to anchor fixtures to brick, block or concrete.
  • Blue Climaseal Coating for Corrosion Resistance & Durability.
  • Cuts its own threads into concrete and other masonry materials.
  • Does not include masonry bit for pilot hole.
Check Stock

Klein Tools 53729 Drywall Anchor Kit for Use in Drywall or Masonry, 100 Anchors

  • Kit contains: 100 #2 Phillips, #10 x 1-Inch Screws, and 100 conical anchors.
  • 1/4-Inch masonry drill bit also included.
  • Light-weight anchor holds screw securely in place.
Check Stock

5/16\-18 Double Expansion Shields (Pack of 12)

  • Zamac Zinc Alloy Concrete Anchors for Masonry Screws or Bolts.
  • Four Part design: a two-piece tubular shield, a hollow, wedge-shaped cone and a wedge-shaped nut-- brought together into a single anchor unit.
  • Used in soft masonry with machine screws or machine bolts.
  • Can also be used in harder materials, including stone, brick, concrete or block.
Check Stock