Reviews Liquid Flow Meter Gauge

CGOLDENWALL Turbine Flow Meter Fuel Meter Digital Flowmeter with FNPT Thread, Flow Meter for Water Diesel Kerosene Gasoline, Flow Rate Range 2.5-26GPM (1 inch Flow Meter)

  • FLOW METER: Before use, please calibrate the flow meter with the liquid to be tested. And the flow rate of the liquid should exceed 2.5 gallons per minute, if the flow rate is too slow, the flow meter cannot measure normally. There is no battery included..
  • MULTI-FUNCTION DISPLAY: High-definition LCD display, can read single cumulative flow, instantaneous flow and total cumulative flow. The clear function can clear the value of cumulative flow, to make sure it is always within the measuring range. If your flow meter cannot work, please contact us in time..
  • HIGH-QUALITY MATERIALS: The aluminum alloy housing is sturdy, durable and corrosion-resistant, which have a long service time. The PCB circuit board make the battery have a long service life, and safe in use. Please NOTE: the LCD display is not water proof.
  • INSTALLATION: The flowmeter can be installed in horizontal and vertical directions, but the flow direction of the liquid needs to be consistent with the direction of the arrow on the flowmeter. There is no direction requirements for the installation of the display screen..
  • MEASURABLE LIQUIDS: The turbine flow meter can used for measuring the water, gasoline, diesel, kerosene, methanol and other low-corrosive, non-viscosity liquids..
Check Stock

Horiba 9096001700 Plastic Body PH Electrode

  • Modular design makes it suitable for use with output modules, sensors and remote transmitters.Compact structure, easy to install.Intuitive clear reading, high reliability, measuring accuracy is ±1%.High-definition displays show both instantaneous and cumulative flow.Can be widely used to measure diesel, kerosene, gasoline, etc..
  • This digital turbine flow meter has modular design, high accuracy, compact size and stable performance. Easy to replace and maintain internal components. Suitable for use with output modules, sensors and remote transmitters..
  • Malfunction and solution:The flow meter is not accurate. 1. The method of field calibration is not correct. Calibrate again. 2. The flow rate on the meter is below the lowest. Increase the flow rate. 3. The flow meter is blocked by the dry liquid. Take out the impeller and clean it carefully and make sure the impeller turns freely..
  • 4. The impeller is wrapped by the sealing material. Remove the meter and make sure the impeller turns freely. 5. Too close to the impeller. Install properly 6. Too close to the motor or electronic noise environment.
  • The meter can not calibrate. 1. Circuit board is break down. Replace the circuit board. 2. Button is fail to press. Replace the circuit board..
Check Stock

BETOOLL HW9003 Argon/CO2 Mig Tig Flow Meter Gas Regulator Gauge Welding Weld

  • Brand New BETOOLL Argon / CO2 regulator and flow meter..
  • Flow Meters are more accurate than the flow gauge regulators..
  • The pressure gauge which shows how much gas is left in the tank goes from 0 to 4000 psi..
  • And this flowmeter does not use a diaphragm, so it is more reliable than the flow-gauge style regulators..
  • The output flow is adjustable from 10 to 60 cfh (cubic feet per hour), and is indicated by a ball which moves up and down in the flow tube..
Check Stock

Argon/CO2 Flow Meter Gas Regulator Compatible with Mig Tig Welder Regulator with 6.6FT Gas Hose 10 to 60 CFH Output Flow 0 to 4000 PSI - CGA-580 Inlet argon flow gauge welding regulator

  • ...rdy and durable, which can withstand harsh environments and have a longer life. Came with 6.6 Ft argon welding gas regulator hose and protective cover are made of impact-resistant composite material for safety and durability.
  • 【Wide Application】Idea choice for CGA 580 Tank Fitting. This Gas Pressure Regulator/Flowmeter Can Be Used with Argon, Helium and CO2 Gas Tanks (CGA-580 Inlet). So it will screw right into the Argon, Argon/CO2 tanks. IDEAL FOR Miller, Lincoln, Hobart, HTP, and most other welders! Idea choice for MIG TIG welding, cutting ,chemical and electronics industry.
  • 【Accurate Gas Flow Gague】Adjustable from 10 to 60 cfh (cubic feet per hour), and is indicated by a ball which moves up and down in the flow tube. 0-4000psi inlet pressure, easy-to-read bottle pressure gauge included, allowing you to view how much gas is left in the tank range 0 to 4000psi. Will fit both the female 9/16" x 18 nut or the male 5/8" x 18 fitting. It also comes with a standard 1/4" barbed fitting.
  • 【Good Design】Use economic style flow meter regulator and single stage piston design, combination of regulator and flow meter as one unit, compact lightweight construction, convenient for use. Argon Regulator is a ideal choice for professional TIG/MIG welding applic....
Check Stock

Flow Meter,Aluminum Alloy 1/2 inch Digital LCD Display High Accuracy Fuel Diesel Flowmeter Water Flow Rate Sensor,Control and Measure Low Flow for Gasoline,Kerosene,Engine Oil Blue

  • ✔【DIGITAL LCD DISPLAY】The aluminum alloy flow meter has LCD screen display, which can provide clear reading. Meanwhile, the LCD display flow....
  • ✔【READING AND ACCURACY】There aluminum alloy fuel diesel flow meter has intuitive clear reading and high reliability on digital stainless steel....
  • ✔【WIDE COMPATIBILITY】The high accuracy fuel flow meter is suitable for high viscosity liquid media such as diesel, gasoline, kerosene, engine....
  • ✔【RELIABLE QUALITY】The blue LCD display high accuracy aluminum alloy fuel diesel flow meter is 100% brand new and high quality. Meanwhile, it is....
  • ✔【100% WARRANTY】We promises every customer a 100% shopping satisfaction, feel free to reach us if you have any questions about your purchase.We....
Check Stock

DIGITEN Water Flow Control Meter LCD Display Controller+G1/2\ Water Hall Sensor Flow Meter Flowmeter Counter 1-30L/min+G1/2\ Solenoid Valve Normally Closed N/C+DC 12V Power Adapter

  • ★【Large LCD Screen & Monitor Flow Rate】: Support reading with Liter or Gallon unit, LPM/GPM switchable. DFC15 will display the flow rate(the REAL-TIME volume of liquid which passes per minute), the flow total volume and sensed temperature clearly..
  • ★【Quantitative Control & Alarm Function】: The controller will turn off the solenoid valve automatically when flow reach to the setting value you desire, it's easy to install and control. It can automatically stop water filling into your concrete mixer. When the total amount reaches the setting value, the controller will alarm..
  • ★【Work with All Hall Effect Flow Sensor】: It can work with various different flow sensors through adjust the K value. High quality, come with temperature sensor, it can measure liquid temperature..
  • ★【Wide Applications】: Swimming pool, water dispenser, coffee machine, drip irrigation system, beer brewing, etc. For example, if you want 5 liters of water, you can set up 5 liters of water on the DFC15 controller. When the water in the container reaches 5 liters, the controller will control the solenoid valve to close it, the water flow automatically stops, and you just get 5 liters of water. Please select a suitable flow meter. An oil flow meter is required for liqu....
Check Stock

Fuel Flow Meter, K24 LCD Turbine Digital Diesel Fuel Flow Meter Gas Oil Fuel Flow Meter Pump Flow Meter Mechanical Meter Widely Used for Chemicals Water

  • 【Our Advantages】: This fuel flow meter has control panel with modular design, fully functional, simple structure, and convenient operation.
  • 【Wide Use】: This fuel flow meter can be widely used in petroleum, chemical, pharmaceutical, transportation, food to be industrial and commercial.
  • 【Media】: This fuel flow meter has methanol diesel fuel kerosene chemical liquid urea water.
  • 【Battery Replace Reminder】: When the battery voltage is 2.2V to 2.4V, display LBat, to remind the user to replace the battery.
  • 【LCD Display】: Large LCD display is convenient for clear reading, and you can easy read the information you need from this large LCD display.
Check Stock

Protmex Anemometer, Digital Handheld Anemometer with USB Interface, Portable Temperature Humidity Wind Speed Meter with LCD Backlight, Air Volume Flow CFM Meter, PT6252B (Battery Included)

  • 【PROFESSIONAL AIR FLOW METER】Protmex PT6252B anemometer is a portable wind speed gauge that can accurately measure airspeed in 5 units: m/s, km/h, ft/min, knots, ft. Users can work under the dim surrounding with your anemometer via the bright backlit LCD screen..
  • 【USB DATA LOGGING AND DATA SYNC ON COMPUTER】The Protmex air flow meter cfm comes with a USB cable and PC software support can connect the wind meter to the computer via a USB port. For wind data logging, analyzing, and monitoring..
  • 【MULTI-FUNCTIONAL ANEMOMETER】The digital handheld anemometer can monitor and record wind speed, air volume, temperature, humidity, dew point temperature, wet bulb temperature, CFM airflow, and RH, perfect for balancing airflow in HVAC tasks such as duct vents, AC air output testing..
  • 【SWITCHABLE READING】The Protmex wind gauge has the functions of reading holding, maximum value, minimum value, etc. With a large-screen LCD and backlight, the multi-unit switching function..
  • 【ACCURATE AIR VELOCITY METER】Our Protmex wind speed meter for measuring wind speed range 0.5~30 m/s(+/- 2% of readings).
  • Wind temperature -20~60℃, -4℉-140℉(+/-0.2℃,32.56℉).
  • 2 temp sensors and 8 vanes make the meter is very sensitive to....
Check Stock

Ancel S3000 EVAP Automotive Smoke Machine Leak Vacuum Diagnostic Tester with Oil Level Gauge & Air Flowmeter for All Vehicle Boat Truck Motorcycle

  • ...bine system, intake manifold, vacuum line, etc..
  • [High performance and high-quality metal structure] Compared to other simple smoke leak diagnostic testers, the ANCEL S3000 smoke machine not only has a built-in air pump, but also has a pressure gauge and an adjustable flow meter. The compressor generates air pressure from 0.8 to 14.5 psi, allowing smoke to be easily introduced into the tested sealing system, speeding up the leak detection process..
  • [Pressure gauge+adjustable flow meter] You can judge whether the tested system has a leak by the pressure change of the pressure gauge. By adjusting the size of the flow meter, you can also better control the amount of visible smoke to locate specific leaks. There are separate air mode and smoke modes to meet your different needs..
  • [Easy operation] A few simple steps can help you detect leaks in the vehicle system. (1) Add tobacco oil (USP mineral oil/baby oil), you need to buy it separately. (2) Check the power cord (12V DC car battery). (3) Connect the system and test for leaks..
Check Stock

Automotive Smoke Machine Leak Detector VXSCAN EVAP Vacuum Leakage Tester Fuel Pipe Diagnostic Tester with Flow Meter & Pressure Gauge for All 12V Vehicles

  • 【EVAP SMOKE MACHINE】VXSCAN V3 is a professional vacuum machine for car fuel pipe system leak detection. Supports EVAP system test, tightness test,....
  • 【EASY TO USE】By heating USP mineral oil or baby oil, the automotive smoke machine can be outputs lots of smoke within 30 seconds, to improve....
  • 【SMOKE FLOW METER & PRESSURE GAUGE】Equipped with pressure gauge and adjustable flow meter which helps you control the smoke effect easily. When....
  • 【Air Mode & Smoke Mode】The V3 smoke leak tester adopts an independent switch control design, the air mode independently controls the built-in air....
  • 【WIDELY COMPATIBILITY】Our package includes all accessories (Oil not included), it supports detect the leaks of multi pipe systems on cars,....
Check Stock

Oxygen Air Flow Meter LZQ-1 1~5LPM Oxygen Carbon Dioxide Measuring Flowmeter Gauge Oxygen Gas Flow Meter

  • HIGH PERFORMANCE: All kinds of gas measurement accuracy is high, suitable for a variety of occasions, you can avoid the trouble caused by the reading error when you measure..
  • PRECISE: The air flow meter is simple, practical and easy to use. The transparent panel type makes the reading simple, convenient and clear..
  • CONVENIENT: Gas flow meter is an instrument for measuring gas rate of flow, which is installed in the pipeline to record the gas flow..
  • Texture of Material: The gauge consists of acrylic, plastic and metal. Lightweight and durable, suitable for long-term use..
Check Stock

BTMETER BT-846A Pro HVAC Anemometer Measures Wind Speed Wind Flow Wind Temperature CFM Air Flow Velocity Meter with Backlight MAX MIN AVG

  • ➤【Pro Air Flow CFM Anemometer 】Accurately measures wind velocity in 5 units: m/s, km/h, ft/min, knots, mph. wind temp in ℃/℉ , air flow in....
  • ➤【Higher Range Wind Speed Meter 】Higher Wind Speed Range: 0.001~100 mph (Accuracy: +/- 3% +/- 0.2 reading), Resolution: 0.001. Air temperature....
  • ➤【Airflow CFM Meter】BT-846A wind speed gauge measures Wind flow range: CFM 0-999900 ft3/min, Resolution: 0.001-100, Air flow area : 0.001-9999....
  • ➤【Separated Extendable Wind Sensor】Built with user-friendly extendable wind sensor vane, so you can still look at the readings easily while you....
  • ➤【Must Have for Air Balancing】 Designed for HVAC trouble-shooting, air flow balancing. The separated wind speed sensor can be replaced if it’s....
Check Stock

Argon CO2 Regulator, Tig Mig Welding Regulator Argon Flow Meter with 6.6Ft Gas Hose CGA-580 Inlet 0-3500PSI Pressure Gauge 10-60 CFH

  • CGA580 CONNECTION - The argon regulator/flowmeter is suitable for standard Gas tanks like argon, CO2, and helium with CGA-580 inlet connection, and has a unique filter port design on the CGA-580 mounting port..
  • PRECISE CONTROL & MEASUREMENT - Our argon CO2 regulator equipped with a flow meter and pressure gauge. Output flow is indicated by a ball in the flow tube and is adjustable from 10 to 60 SCFM (standard cubic feet per minute).The pressure gauge ranges from 0 to 3500 PSI and is used to read the amount of gas remaining in the tank..
  • RELIABLE QUALITY - The bodies of our argon flow meter is made of high-quality brass to withstand harsh environments and have a longer life. The flowmeter tube and protective cover are made of impact-resistant composite material for safety and durability..
  • APPLICATIONS - The gas pressure regulator can be used with argon, CO2 and helium. Ideal for MIG TIG welding, chemical and electronics industry. The welding gas regulator is an economic alternative for the customers who wants more precise gas metering..
  • PACKAGED WITH HOSE - Our argon regulator package comes with a 2m/6.6 Ft hose that will completely protect you from injury in adverse conditions and keep your tank a safe distance from your welding project..
Check Stock