Reviews Light Aggregate Concrete Block

Concord Blades CBW03000SP 3 Inch Wet Concrete Diamond Core Drill Bit

  • 10 mm segment height, 3.5mm Segment Width, 1-1/4" -7mm Arbor.
  • This core bit is used for wet drilling on cured concrete with hard aggregate and medium to heavy steel reinforcement, and asphalt overlay on concrete.
Check Stock

5 GAL Armor AR500 High Gloss Solvent Based Acrylic Concrete Sealer and Paver Sealer

  • Penetrating high solids, breathable solvent based acrylic coating with unmatched bonding characteristics..
  • Durable, long lasting. Stands up to abrasion, UV rays, hot tire pick up, hot and cold temperatures..
  • Long lasting high gloss finish provides up to 2-5 years of life on a two coat application before the need for a recoat. Will bring out color in dull and faded surfaces..
  • Can be used on poured concrete, stamped concrete, concrete pavers, aggregate, and more..
  • Can be used on unsealed surfaces, or on surfaces previously sealed with a solvent based acrylic..
Check Stock

Mutual WF200 Polyethylene Woven Geotextile Fabric 300 Length x 6 Width

  • Woven geotextiles are used to hold soil in place, and can also be used under rip rap, gabions or precast block.
  • Woven geotextiles area time and money saving alternative to traditional methods using graded aggregate or sand filters.
  • They prolong the surface life and stabilize the foundation while providing a rugged separation layer between aggregate and subgrade.
  • Measures 6-feet width by 300-feet length.
Check Stock

MRO Chem Perfect Patch 100 Percent Concrete Epoxy Patching Repair System Kit Restores Cracked Pitted or Worn Concrete Surfaces 50 Pounds 5 Gallons

  • EPOXY PATCHING SYSTEM: Permanent epoxy patching system seals cracks and holes and smooths over pitted concrete surfaces.
  • SUPER STRONG: Restores and even exceeds the strength of the original concrete.
  • Withstands traffic and even loads of up to 10,000 pounds.
  • COVERAGE: 50-pound, 5-gallon pail covers up to 100 square feet with a 1/8-inch thick coat.
  • APPLICATION: Three-part mixture includes epoxy, hardener, and aggregate.
  • Apply with a trowel, hand tamp, or roller for even coating.
  • USES: For use on walkways, staircases, streets, walls, ramps, and any indoor or outdoor concrete surface.
Check Stock

Deck Grip Non-Slip Sealer (5 Gallon) Clear Barefoot-Friendly Anti-Slip Coating - Create Traction for Outdoor or Indoor Floors and Pool Decks

  • ...-icing salts & chlorine. 5-Gallon Pail (treats 1500-3000 feet). Coverage is dependent on surface porosity..
  • SUITABLE SURFACES: Deck Grip is ideal for use on sealed or unsealed concrete, natural & manufactured stone, stained or unstained concrete, stamped or exposed aggregate concrete, brick, slate, sealed or unsealed tile & flagstone. Use Deck Grip on garage floors, driveways & sidewalks, pool decks & patios, entryways, as well as, warehouse & retail floors. Not for use on wood or composite wood surfaces..
  • LONG LASTING: If applied & maintained correctly, your floor will remain slip resistant for 2 years or longer. To maintain the surface after coating it with Deck Grip, routinely sweep and rinse using light pressure. To remove oily deposits or other foreign matters, use a pH-neutral cleaner and scrub lightly with a soft bristle deck brush..
  • SIMPLE & EFFECTIVE: Deck Grip is almost odorless & requires only moderate surface prep prior to treatment. Read & follow instructions carefully. Clean & dry the surface & apply Deck Grip with a 3/8” nap roller (included). Two thin coats a....
Check Stock

U. S. Chemical & Plastics Feather-Rite Lightweight Autobody Filler, Gallon (USC-21330) (4)

  • Pre-measured adhesive of polyester resin base, quartz sand and benzoyl peroxide hardener.
  • Sand and aggregate mixture is closest to natural concrete.
Check Stock

SUPERCOAT Stone Gray Epoxy Floor Coating

  • Breathable two-part waterborne epoxy coating, Decorative flakes, Anti-slip aggregate, Cleaner/Degreaser included.
  • Professional grade floor covering, Easy to install, No acid etching or mechanical prep necessary in most cases, Clean with degreaser included, mix and apply with roller, Scatter flakes in wet epoxy.
  • Epoxy coating breathes allowing moisture vapors to pass through eliminating blistering and peeling, Resistant to automotive fluids, hot tire lift, Good adhesion to concrete and wood.
Check Stock

Starrett KD0300-N 3-Inch Diamond Grit Holesaw

  • Effective cutting of hardened steels, fired ceramics, aggregate containing concrete, non-metallics and other difficult to cut materials.
  • Uniform synthetic diamond grit bonded over a durable steel platform.
  • Always use a coolant and start at a low speed, increase speed as ease of cutting is noticed while avoiding heat build-up on the cutting surface.
  • Recommended cutting speed is from 150 to 300-RPM.
Check Stock

Starrett KD0400-N 4-Inch Diamond Grit Holesaw

  • Effective cutting of hardened steels, fired ceramics, aggregate containing concrete, non-metallics and other difficult to cut materials.
  • Uniform synthetic diamond grit bonded over a durable steel platform.
  • Always use a coolant and start at a low speed, increase speed as ease of cutting is noticed while avoiding heat build-up on the cutting surface.
  • Recommended cutting speed is from 150 to 300-RPM.
Check Stock

Starrett KD0600-N 6-Inch Diamond Grit Holesaw

  • Effective cutting of hardened steels, fired ceramics, aggregate containing concrete, non-metallics and other difficult to cut materials.
  • Uniform synthetic diamond grit bonded over a durable steel platform.
  • Always use a coolant and start at a low speed, increase speed as ease of cutting is noticed while avoiding heat build-up on the cutting surface.
  • Recommended cutting speed is from 150 to 300-RPM.
Check Stock

Zep HDSWEEP50 Floor Sweeping Compound, 50 lb

  • BEAUTIFUL WET LOOK SEALER Works on exposed aggregate, stamped, colored or decorative surfaces.
  • WILL NOT SIGNIFICANTLY DARKEN MOST SURFACEs when it dries. Does not look like you sprayed water on it. Resists chemicals and oil, Durable, Clear & Non-Yellowing..
  • PLEASE READ COMPLETE PRODUCT DESCRIPTION: Not for polished GRANITE OR MARBLE.
  • SPRAY, BRUSH OR ROLL on concrete, pavers, slate, driveways, garage floors, patios, masonry, brick warehouse floors.
  • MADE IN THE USA. Professional Results VERY low odor dries in hours..
Check Stock

Deck Grip Non-Slip Concrete and Tile Coating – Clear Barefoot-Friendly Anti-Slip Sealer - Slip Resistant Coating for Outdoor or Indoor Floors and Pool Decks

  • ...lon (treats 300-600 feet) or 5-Gallon Pail (treats 1500-3000 feet). Coverage is dependent on surface porosity..
  • SUITABLE SURFACES: Deck Grip is ideal for use on sealed or unsealed concrete, natural & manufactured stone, stained or unstained concrete, stamped or exposed aggregate concrete, brick, slate, sealed or unsealed tile & flagstone. Use Deck Grip on garage floors, driveways & sidewalks, pool decks & patios, entryways, as well as, warehouse & retail floors. Not for use on wood or composite wood surfaces..
  • LONG LASTING: If applied & maintained correctly, your floor will remain slip resistant for 2 years or longer. To maintain the surface after coating it with Deck Grip, routinely sweep and rinse using light pressure. To remove oily deposits or other foreign matters, use a pH-neutral cleaner and scrub lightly with a soft bristle deck brush..
  • SIMPLE & EFFECTIVE: Deck Grip is almost odorless & requires only moderate surface prep prior to treatment. Read & follow instructions carefully. Clean & dry the surface & apply Deck Grip with a 3/8” nap roller (included). Two thin coats a....
Check Stock

Starrett KD0414-N 4.1/4-Inch Diamond Grit Holesaw

  • Effective cutting of hardened steels, fired ceramics, aggregate containing concrete, non-metallics and other difficult to cut materials.
  • Uniform synthetic diamond grit bonded over a durable steel platform.
  • Always use a coolant and start at a low speed, increase speed as ease of cutting is noticed while avoiding heat build-up on the cutting surface.
  • Recommended cutting speed is from 150 to 300-RPM.
Check Stock