Reviews Jk Axle U Joint

NICHE High Strength Rear Left and Right CV Axle Kit for 2003-2008 Yamaha Grizzly 660 5KM-2530U-13-00

  • Includes Rear Left Axle, Rear Right Axle.
  • Rear-Left CV Axle Compatible with Yamaha 5KM-2530U-13-00, 5KM-2530W-12-00, Rear-Right CV Axle Compatible with Yamaha 5KM-2530T-13-00, 5KM-2530V-12-00.
  • Compatible with: Yamaha 2003-2008 Grizzly 660, 2005-2008 Grizzly 660 Hunter Edition, 2003 Grizzly 660 Metallic Titanium Limited Edition, 2003-2004, 2006 Grizzly 660 Hardwoods Hunter Edition, 2003-2005.
  • 25% Larger Joint and Shaft Diameters When Compared to Factory Specifications.
  • Durable Neoprene Boots Ultra-Low-Profile Boot Clamps Prevent Moisture or Water Damage.
Check Stock

For 10-22 Ford F250 17 Inch Silver Steel Rim - OE Direct Replacement - Road Ready Truck Wheel

  • Replacement for 1999-2004 Ford F-250 / Ford F-350 Super Duty (4x4.
  • Both (2) Brand New Front Driver & Passenger Side Axle w/U-Joint for 1999-2004 F-250/F-350 35 Spline Dana 60 Axle.
  • Both (2) Front Wheel Bearing And Hub Assembly Set "Coarse Threads" - 515020.
  • FITS DANA 60 4x4 Single Rear Wheel Models Only - Coarse Hub Threads and ABS.
Check Stock

Inner CV Joint Puller Slide Hammer Front Wheel Drive Axle Half Shaft Removal Tool Kit CV Axle Removal Tool Slide Hammer 63mm 48mm CV Joint Fork Adapter Attachments

  • ⚒️ Quick to Remove CV Axle ⚒️ - With this CV axle removal tool the axle assembly is popped out of trans axle, and install the new axle,not need spend a lot of effort. Without damage to transmission case or inside roller bearing..
  • ⚒️ Perfect Joint Fork ⚒️ - This slide hammer puller set includes opening 63mm and 48mm CV joint fork disassembly adapter, the CV Joint Fork is be threaded internally, and the Slide Hammer stick is threaded externally. the joint fork could fit on the slide hammer stick, 63mm and 48mm fit most vehicle models, have wide use..
  • ⚒️ Heavy Duty ⚒️ -This slide hammer weighs 10.5 pounds and is 19.5 inches long, which is larger than the normal ones. So it has enough length to slide to generate more force, easier to use and work better.The hammer and VC joint fork are made of heavy-duty steel, durable and not easy to break..
  • ⚒️ Easy to Use ⚒️ - You need to attach the inner CV axle puller to your axle slide hammer, then place the adapter around the axle after the inner start. Slide the 10 lb. hammer weight back and forth to create torque and pull out the axle. Note: you can use....
Check Stock

OMT Inner CV Axle Puller Tool Set with 5/8"-18 Slide Hammer & Adapter | Inner CV Joint Removal Tool Kit | Front Wheel Drive Axle Puller Set Compatible with Taurus Sable FWDs from 1986 to 2021

  • PULL CV JOINTS & AXLES: This CV joint puller tool set by Orion Motor Tech is compatible with Ford Taurus and Mercury Sable models from 1986 to present, loosening and removing their front wheel drive axles and hidden retaining rings in minutes.
  • MULTIPURPOSE SLIDE HAMMER: Our slide hammer weighs 7 pounds for extra strength to give you a straight and even pull for damage-free removal of the axle assembly.
  • its threading also lets you use it with other 5/8"-18 adapters to deal with other makes and models or to handle other work around your engine.
  • DURABLE PULLER ADAPTER: The U-shaped CV joint fork has a 2-inch opening and 2.4-inch depth to firmly lock onto your Sable or Taurus axle assembly, making removal of stuck CV joints a cinch.
  • QUICK & EASY OPERATION: These automotive tools work together to provide straight and even force so your constant velocity axle pops out smoothly, leaving the roller bearing inside the joint and the rest of your vehicle untouched.
  • BUILT TO LAST: Made of premium AISI 1045 medium carbon steel, our CV joint removal set provides strong and dependabl....
Check Stock

RCV Performance CVJ44 CV Axle Set

  • Overall Lengths: 18.75 L | 34.45 R | 6.25 Stub.
  • Finished Coating: Black Oxide/Material: 4340 Chromalloy.
Check Stock

Eaton 912A585 Detroit Truetrac 27 Spline Differential for Dana 30

  • Ring Gear Size: 7.2 IN, Ring Gear Ratio: 3.73 & up.
  • Catalog Notes: Applies to non-disconnect only.
Check Stock

E-cowlboy Inner CV Joint Puller Slide Hammer Front Wheel Drive Axle Half Shaft Removal Tool Kit,63mm 48mm CV Joint Fork Adapter,Heavy Duty 10 Pounds Slide Hammer

  • 【Slide Hammer Puller Set with Plastic Suitcase】: This kit include: 1 heavy duty slide hammer.
  • 2pc 16mm nut. this kit have everthing you need to remove CV axle or half shaft, all the tools put in a plastic case, easy to carry..
  • 【 Perfect Joint Fork】 ： This slide hammer puller set includes opening 63mm and 48mm CV joint fork disassembly adapter, the CV Joint Fork is be threaded internally, and the Slide Hammer stick is threaded externally. the joint fork could fit on the slide hammer stick, 63mm and 48mm fit most vehicle models, have wide use..
  • 【Slide Hammer Made of Heavy Steel】The slide hammer and the CV joint fork is made of heavy-duty steel, which can withstand huge pressure without deformation, is not easy to break, and is more durable. The sliding distance is 19.5 inches, and the weight is 10 pounds .The overall ergonomic design of the slide hammer, the handle is curved, the surface is large, and it is more comfortable to use. Use this universal joint slide hammer to work more efficiently..
  • 【Quick to Remove CV Axle 】：With thi....
Check Stock

10lb Heavy Duty Inner CV Axle Removal Tool for FWD Vehicles Front Wheel Drive Axle Half Shaft Removal Tool,CATUDIY Inner CV Joint Puller Tool & Slide Hammer Puller Set with 48&63MM Joint Fork Adapters

  • Useful CV Axle Puller: To replace or repair the CV axle joints easily, use this slide hammer kit. The CV joint puller adapter and large slide hammer bearing puller allow to create added torque to loosen and remove stubborn axle shafts and water pumps, without damaging to transmission cases or other components.
  • Efficient Front Wheel Drive Axle Puller Set: Efficient & Heavy-Duty: Our 10.5 lb curved slide hammers are heavier and larger, and the length of 19.5 inches ensures sufficient length slide to generate more force(so the generated pulling force is also twice than normal 5lb slide hammer). Save efforts and works more efficiently.
  • Combination Kit Fits All Needs: The CV axle joint pulley removal tool includes a T-style slide hammers, a steel wire joint puller, 2pc 16mm nuts, opening 63mm and 48mm CV joint fork removing attachments. All you need to remove CV axle or half shaft are put in this easy-carrying plastic case.
  • Superior Material: Heat-treated FWD axle puller adapter with black oxide finish is durable and resists rust and corrosion. Slide hammer and the VC join fork is made of high quality heavy steel materials w....
Check Stock

NEW SUPERСHIPS FLASHPAQ F5 HANDHELD,COMPATIBLE WITH 1999-2014 JEEР WRANGLER

  • Features: Corrects speedometer for tire upgrades between 26- 42" (JK Models Only) | Equipped with Superсhips industry-leading performance | Crawl for low speed off-roading in 4WD (JK only) | Speedometer recalibration for gear/axle swaps up to 5.38 | Locking axle options with transfer case in 4-Hi & 4-Low (2007-14 Rubicon only) | ESP stability optimization (2011-14 auto transmission models only) | Engine idle adjustability for winching | Reads & clears diagnostic trouble codes.
  • Daytime running light options (2007-14 models only) | 1 touch lane change | TPMS On/Off | Accessory delay options (2011-14 models only - Includes adjustable delay for radios, accessory lights & other aftermarket accessories tied to same fuse) | Headlamp delay options (2011-14 models only) | Horn chirp & exterior lighting flash options when locking doors with keyless entry | Internet updatable.
  • NOTE: Results & feature set may vary based on vehicle make, model & aftermarket upgrades. Read all instructions before install &/or operation of this product | NOTE: Has not been tested ....
Check Stock

Orion Motor Tech 21PCS Master Ball Joint Press | Upper and Lower Ball Joint Removal Tool | Automotive Mechanic Tool Set

  • ESSENTIAL TOOL FOR BALL JOINT SERVICE - Use the ORION MOTOR TECH 22PCS Ball Joint Press Set Ball Joint Tool / Bushing Removal Tool with multi-size adapter to effortlessly remove press fit parts including ball joints, U-joints, brake anchor pins, and more on most 2-wheel drive (2WD) and 4-wheel drive (4WD) vehicles without removing the control arm from the vehicle..
  • UNIVERSALLY COMPATIBLE WITH A WIDE RANGE OF VEHICLES - Use the ORION MOTOR TECH Ball Joint Press Set Ball Joint Tool / Bushing Removal Tool with all the receiver tubes and removing/installing adapters needed to effortlessly remove press fit parts including ball joints, U-joints, brake anchor pins, and more on most GM, Chevy, Ford, and Dodge 2 and 4 wheel drive pickups, vans and sport utility vehicles, will service perfect for vehicles having the Dana 28, 30, 35, 44, 60 axle.
  • PROFESSIONAL GRADE QUALITY AND DURABILITY - Off road weekend warriors, novices, and professional mechanics trust the ORION kit because ORION MOTOR TECH sources the highest quality components from around the world. Constructed from heavy-duty forged solid carbon steel with anti-rust black-oxide finish on adapters for maximum strength and longevity that resists rust and corrosion..
  • CONVENIENTLY ORGANIZED IN CUSTOM MOLD....
Check Stock

ABN Inner CV Axle Removal Tool - CV Axle Puller Slide Hammer Set with 5 lb Slide Hammer and CV Joint Puller Adapter

  • [Remove Front Wheel Drive Axles Easily] To replace or repair your CV axle joints easily, use the ABN FWD Axle Puller Slide Hammer Puller Set.
  • The CV joint puller adapter and large slide hammer bearing puller allow you to create added torque to loosen and remove stubborn axle shafts and water pumps.
  • [Fits Your Needs] Chrome-plated 23 x 5/8-inch hammer bar features a 5/8-inch x 18 threaded section to fit your adapters, while the slide hammer CV axle adapter has 48mm (roughly 2-inch) opening and a 2.5-inch depth to fit your needs.
  • [Easy to Use] Attach the inner CV axle puller to your axle slide hammer then position the adapter around the shaft behind the inner boot.
  • Slide the 5 lb hammer weight back and forth to create torque to pull out the axle.
  • Use lubricant fluid for added ease (not included).
  • [Safe for Your Vehicle] Slide hammer CV joint puller and attachment design focuses the added torque to the back of the housing to prevent damage to the roller bearing inside the joint.
  • Pulls CV joints on 1986-current Taurus/Sable.
  • [Built to Last] Hardened hammer shaft provides strength and d....
Check Stock

MG21103 Front Axle Tube Seal Kit for Jeep JK TJ XJ ZJ MJ Dana 30 & Dana 44 (2 PCS)

  • FITMENT: Fits Jeep XJ, YJ, TJ and JK Dana 30 and Dana 44 front axles (NOT fit models with dis-connect front dana 30 axle’s).
  • MATERIAL: Made from high quality Billet Aluminum with anti-corrosion coatings and Double Lip Seal, durable in use.
  • APPLICATION: Prolong your front axle tubes’ life by keeping water, mud and debris from entering front axle tubes.
  • NOTE: Use on Non-Vacuum Disconnect applications (Will Not Work with Wrangler models that have Vacuum disconnect Two-piece axle shaft).
  • SATISFACTION GUARANTEE: If you’re not 100% satisfied with Dana Axle Tube Seal Kit, simply return it for a full refund in 30 days. Premium Support & 12-Month Warranty.
Check Stock

LainKeen Inner CV Joint Puller Front Wheel Drive Axle Half Shaft Removal Tool Kit with Heavy Duty 10 Pounds Slide Hammer, 63mm 48mm CV Joint Fork Adapter Attachments

  • Remove CV Axle Easily: Using the CV joint puller, you can easily pull the old stubborn CV axle and install the new axle without damaging the expensive aluminum transmission cases and other parts..
  • Heavy Steel Slide Hammer: The slide hammer and the VC join fork is made of heavy duty steel, which can withstand huge pressure without deformation, is not easy to break. slide hammers are heavier and larger than normal ones, hammer weight is 10.5 lb, is twice the average slide hammer, so the generated pulling force is also twice of a normal slide hammer, the length is 19.5 inches, so it can generate greater pulling force and work easier..
  • Efficient Slide Hammer: The overall ergonomic design of the slide hammer, the handle is curved, the surface is large, and it is more comfortable to use. Use this universal joint slide hammer to work more efficiently..
  • Wih 63mm 48mm Joint Fork: Our kit include opening 63mm and 48mm cv joint fork removing adapter, the CV Joint Fork is be threaded internally, and the Slide Hammer stick is threaded externally. the joint fork could fit on the slide hammer stick, 63mm and 48mm are suitable for most veh....
Check Stock