Reviews Jet Proshop Table Saws

JET 725004 ProShop II Dado Insert

  • Fits models JET JPS2-115 and JPS2-230 ProShop Table Saws.
Check Stock

Leecraft JT-7 Zero Clearance Table Saw Insert (For Jet/Laguana)(Colors May Vary)

  • Fits: Jet ProShop Saw: JPS-10TS, 708490, 708491, 708493, 708494, 708495, Laguna Fusion 1.75hp 10" Table Saw, Baleigh TS-1044H, General International 50-090R M1.
  • Measures: 14" x 4-1/8" x (Please measure before ordering).
  • Offers superior rigidity, flatness, durability, and low friction.
  • Eliminates dangerous gap around blade where thin off-cuts can get wedged.
Check Stock

Leecraft JT-8 Zero Clearance Table Saw Insert (For Jet/Laguna)(Colors May Vary)

  • Fits: Jet ProShop Saw: JPS-10TS (only models 708490, 708491, 708493, 708494, 708495).
  • Laguna Fusion 1.75hp 10" Table Saw, Baleigh TS-1044H, General International 50-090R M1.
  • Offers superior rigidity, flatness, durability, and low friction.
  • Eliminates dangerous gap around blade where thin off-cuts can get wedged.
  • Measures: 14" x 4-1/8" x (PLEASE measure before ordering) Installation instructions included.
Check Stock

Powermatic 1791792B Low-Profile Thin Kerf Riving Knife for PM2000B Saw

  • Allows for use of thin kerf table saw blade for non-through cuts..
  • Compatibility: Designed to fit Powermatic PM2000B table saws..
  • JET Red Assurance Guarantee: Backed by JET's industry-leading one-year warranty against manufacturing defects..
Check Stock

WoodRiver Adjustable Fence Clamps, 2 Piece

  • This fence will improve your band saw instantly. Easy to adjust for blade lead with angle bracket design. Will fit most 14" band saws with tables up to about 16" square..
  • Bolts directly to existing holes in the 14" Delta, Jet, Ridgid, Powermatic (without extension table) & Porter Cable. May be able to be attached to other 14" band saws by drilling four holes, see instruction sheet..
  • The most rigid fence available. Two separate fence position locks at both ends and two separate blade lead locks as well..
  • See the HD Band Saw Circle Jigs - 7286-7290 too. Clamps to any band saw to cut circles or arcs from 3" diameter up to 189.
Check Stock

Thomegoods Urethane Band Saw Tires FIts 12 inch x 7/8 inch x .095 inch No Adhesive Needed Fits for Jet Grizzly, & Powermatic

  • Please measure your saw as some Delta & Rockwell &Grizzly14" bandsaws has slightly smaller holes for the throat plate. If so some slight filing or sanding may be required.If you mind, please don't buy it..
  • Make sure your insert recess has the locating pin on the side, not on the rear..
  • use on 14" Band Saws and 24" Scroll Saws.2&1/2" X .100 thick Please measure your saws recess to ensure proper fit.
  • They fit Delta, Rockwell, some Jet, Ridgid, Grizzly, and other imports..
  • IMPORTANT INSTALLATION NOTE:I have sold several hundred of these and occasionally someone will have the problem of it being a bit too large. First make sure the lip of the hole is free from dirt. If a table alignment pin,is not tight or missing,often the blade mounting slot will close up some over time which reduces the insert hole diameter slightly. I tap a flat head screw driver into the blade installation slot a bit to wedge it open. That should spread the insert hole enough for it to fit.
Check Stock

[2 Pack] 12 inch x 7/8 inch x .095 inch Urethane Band Saw Tires - No Adhesive Needed - Compatible with Branded Bandsaws Including Jet Grizzly, Powermatic

  • use on 14" Band Saws and 24" Scroll Saws.Table Inserts (pack of 2). Material: Aluminum.
  • They fit Delta, Rockwell, some Jet, Ridgid, Grizzly, and other imports..
  • Make sure your insert recess has the locating pin on the side , not on the rear.
  • IMPORTANT INSTALLATION NOTE:I have sold several hundred of these and occasionally someone will have the problem of it being a bit too large. First make sure the lip of the hole is free from dirt. If a table alignment pin,is not tight or missing,often the blade mounting slot will close up some over time which reduces the insert hole diameter slightly. I tap a flat head screw driver into the blade installation slot a bit to wedge it open. That should spread the insert hole enough for it to fit.
  • Please measure your saw as some Delta & Rockwell 14" bandsaws has slightly smaller holes for the throat plate. If so some slight filing or sanding may be required..
Check Stock

Table Inserts (Pack of 3) for 14' Band saws or Scroll saws,Diameter: 2.5 in, Thickness: 0.1 in.(Please make sure this is your size)

  • Three inserts to protect your expensive blades Please measure your saw as some Delta & Rockwell &Grizzly14" bandsaws has slightly smaller holes for the throat plate. If so some slight filing or sanding may be required.If you mind, please don't buy it..
  • use on 14" Band Saws and 24" Scroll Saws..
  • 2&1/2" X .100 thick Please measure your saws recess to ensure proper fit They fit Delta, Rockwell, some Jet, Ridgid, Grizzly, and other imports..
  • Make sure your insert recess has the locating pin on the side, not on the rear.
  • IMPORTANT INSTALLATION NOTE:I have sold several hundred of these and occasionally someone will have the problem of it being a bit too large. First make sure the lip of the hole is free from dirt. If a table alignment pin,is not tight or missing,often the blade mounting slot will close up some over time which reduces the insert hole diameter slightly. I tap a flat head screw driver into the blade installation slot a bit to wedge it open. That should spread the insert hole enough for it to fit.
Check Stock

Jet 708482K JPS-10: 10-Inch ProShop Table saw 1-3/4HP 30-Inch Cast Wings

  • EXCLUSIVE 30" ProShop fence system with T-square design.
  • Integrated arbor lock allows for quick, safe and easy blade changes.
  • Heavy-duty cast iron table with T-style miter slot provides large flat work surface and increased cross cut capacity.
  • Enclosed cabinet with EXCLUSIVE leg stand design for easy assembly.
  • 4" dust port for increased dust collection efficiency.
Check Stock

JET Replacement Blade, 1/4\ X .025\ X 197\ X 14R, for VBS-3612 Band Saw (5674030)

  • Compatibility: Designed to fit JET VBS-3612 band saws..
  • Replacement blade for JET 1/4" x .025" x 197" carbon steel..
  • Quality Manufacturing: Proudly made in the USA..
Check Stock

POWERTEC 71142 Universal Table Saw Miter Gauge Assembly/Miter Gauge with 27 Angle Stops

  • FUNCTION: A high performance woodworking angle tool that possesses a miter guide which mounts into the miter slots of your table saw (band saws and other applications) and then guides the miter gauge parallel to the blade for high precision angled and crosscuts.
  • FEATURES: A lightweight design with a durable laser-cut aluminum construction, large gauge handle, universal fence mounting bracket, pivoting locking mechanism, a removal plate that allows the miter gauge to be used with T-slotted and non T-slotted miter slots, and adjustable expansion discs that remove all side play from the bar, creating a perfect fit..
  • PRECISION: Angle guide with 27 total locking stops in 5 degree increments over a full 180-degree range, and allows for plus or minus 60-degree range miter cuts.
  • UNIVERSAL DESIGN: Works with most Contractor style, full sized saws, or tools with standard miter slots (3/4” width x 3/8” depth) with or without T-slots, making it compatible with popular brand table saws, band saws, router tables, disk and belt sanders. PLEASE NOTE : will not work with smaller saws or tool with 5/8” miter slots..
Check Stock

Jet JWBS-14DXPRO Wood Band Saw Blade Thrust & Guide Bearings. Set of 10 BB-608ZZ

  • Thrust Bearing Set for JWBS-14DXPRO" Jet Band Saws. Set of 10..
  • Full set to replace both the upper and lower positions..
  • Bearings have a 8mm ID, 22mm OD, and are 7mm thick..
  • These are sold under Jet part numbers: BB-608ZZ.
  • This bearing set is for the DXPRO model only.
Check Stock

POWERTEC 71009 Safety Push Block and Stick Set | 5 Pack | Ergonomic Handles with Max Grip | Push blocks and Sticks for Table Saw, Jointers and Woodworking | for Woodworker Safety & Control

  • 【Table saw dust bag 】 : effective at keeping your work area clear of debris. this table saw dust bag is designed for use with the bosch 4000, 4100, GTS1031, and GTS1041A table saws. It also can be used with other table saws that have 2-1/2 inch dust ports on the exterior of the saw..
  • 【Sawdust collector bag】: fits various 10 inch table saws with 2.5 inch dust ports ! Suitable for many different brands, compatible with Bosch Dewalt Makita Ryobi Ridgid Craftsman Porter Cable Rigid Metabo Kobalt Skilsaw Delta. Replaces Bosch part TS1004.
  • 【size】:The dimensions of the dust bag are L 29.5" x W 9.8.
Check Stock