Reviews Injector Pump

Tool Daily Compatible Chemical Injector Set for Pressure Washer, Replacement for Briggs and Stratton 190593GS 190635GS 203640GS

  • Pressure Washer Soap Injector Kit, compatible Briggs & Stratton Pump 190593GS, 190635GS and 203640GS. Please identify the part number of pressure washer pump, then check if it fits your pressure washer..
  • How to replace: Follow soap hose to end and you’ll find injector. Take off soap hose. Use wrench to remove old injector. Clean out any gunk or dried soap in receptacle. Make sure rubber o ring is on injector as pictured. Put ball bearing inside injector and then the spring with small end of spring against the ball bearing. Insert injector into receptacle and tighten injector with 13mm wrench. Don’t overtighten, you’ll break the o ring or crack white metal on pump. Put the soap hose back on..
  • If the part on your pressure washer part is worn-out, rusted or hard-water-deposit clogged, you can replace it with this set..
  • Package List: Two Chemical Injector Sets, including 2 Brass Barbs, 2 Check Valve Balls, 2 Springs, 4 O-Rings..
Check Stock

M MINGLE Adjustable Chemical Injector Kit for Pressure Washer, Soap Injector, 3/8 Inch

  • ★Attention: Max pressure is 3200 PSI. Pressure washer downstream chemical injector kit includes chemical injector, 10 feet tubing (siphon hose), filter and black soap nozzle..
  • ★Used to siphon detergent out of separate container. The chemical or soap runs after pump, which will not damage pump. Great for cleaning or spraying..
  • ★Control metering valve to adjust dilution ratio of chemical and water. Chemical-resist and poly strainer reduces injector clogging..
  • ★Soap injector has universal 3/8’’ quick disconnect. It connects between pressure washer pump and hose..
  • ★Flow rate is from 2 GPM to 5 GPM. Works with most brands of gas and electric pressure washer, cold and hot water pressure washer..
Check Stock

Tempono Pressure Washer Soap Injector Downstream Injector for Pressure Washer Power Washer Chemical Injector Kit 4000 PSI 3/8 Inch Quick Connect

  • Pressure chemical injector ensures that chemicals do not pass through the pump. Protect the performance of the pump and extend its service life..
  • Chemical injector kit has 10 ft tube, soap injector, filter, nozzle and teflon tape. Max pressure is up to 4000 PSI..
  • Chemical injector has an metering valve. You can control the concentration of the liquid. Flow rate is 2 to 5 GPM..
  • Downstream injector for pressure washer with 3/8 inch quick connector. Please pay attention to mark of arrow direction on injector, do not install it....
  • The coupler is made of stainless steel and brass, sturdy and durable. Siphon hose is made of high-quality PVC, suitable for hot and cold water..
Check Stock

PWACCS Adjustable Soap Chemical Injector for Pressure Washer, Downstream Injector for Power Washer, 3/8 Inch Quick Connect

  • Attention: Pressure washer chemical injector's working pressure is from 1000 to 3200 PSI. Flow rate: 1.5 GPM to 4 GPM. The presure which is higher than 3200 PSI will not work. Include chemical injector, 10 Feet tubing, filter and black soap nozzle..
  • Application: Downstream injector for pressure washer is used to siphon detergent out of separate container. The chemical runs after pump. So it allows for a wider choice of chemicals..
  • Chemical injector has standard 3/8’’ quick connect plug and 3/8’’ quick connect socket. Soap injector for pressure washer connects pressure washer pump to hose. Adjusts the dilution ratio of chemicals and water by metering valve..
  • Dilution ratio of chemical vs water can been adjusted by controlling metering valve. Ideal for most brands of gas and electric pressure washer. Suitable for cold and hot water pressure washer..
  • If the pressure washer chemical injector kit have any questions, please contact us at first time. We provide a service of quick reply within 24 hours..
Check Stock

Tool Daily Adjustable Soap Chemical Injector for Pressure Washer, 3/8 Inch Quick Connect

  • ATTENTION: Working pressure is 1000 to 2800 PSI. Flow rate is from 2 GPM to 5 GPM. 2800 PSI or higher will not work. Power washer chemical injector kit includes chemical injector, 10 Feet tubing, filter and black soap nozzle..
  • Application: Must Follow Manual to Set Up Chemical Injector. It is used to siphon detergent out of separate container. The chemical runs after pump. So it allows for a wider choice of chemicals..
  • Chemical injector has standard 3/8’’ quick connect fitting. It connects pressure washer pump to hose..
  • Dilution ratio of chemical vs water can been adjusted by controlling metering valve..
  • Works with most brands of gas and electric pressure washer. Suitable for cold and hot water pressure washer..
Check Stock

Artisan Smoker Meat Injector Kit - Meat Injector Gun with BBQ Marinade Injector Syringe Stainless Steel Needles Siphon Extra O-Rings - Smoker or Grill Flavor Injector for Turkey Pork Brisket

  • BBQ LIKE A PRO with Artisan Smoker’s food syringe injector. Your pro-grade bbq meat injector gun that will add a juicy explosion of seasoning in....
  • DIAL IN FLAVOR injector for meat of all cuts. Has 3 bbq marinade injector flow settings for even distribution. Use as a turkey injector syringe, in....
  • COMFORTABLE, lightweight, portable bbq injector syringe pump with grip handles. Zero hand fatigue. The perfect meat injector kit for smoker fun with....
  • EASY TO CLEAN, dishwasher safe. Inject steak, lamb, blended up sauce or marinades. Dissemble meat injector syringe needles and siphon for cleaning.
  • THE VERY BEST food injector syringe kit. Made from safe durable plastic. Each 304 stainless steel meat injection needle is designed for deep....
Check Stock

Pressure Washer Manifold Kit Fits for Briggs Stratton | OE Replacement 16031 190627GS 190574GS 020228, with 4 Bolt Power Pressure Washer Pumps

  • ...pressure washer pump can be inserted completely inside to make the pin more secure, the sturdy alloy casing helps protect the washer pump from damage, advanced manufacturing technology, high reliability and high performance, standard size, can be easily installed without leakage..
  • The Method of Installing a Chemical Injector: The tools that need to be prepared include a half-inch wire wrench or a half-inch sleeve, and a long and thin tool for penetrating into narrow places. Use a half-inch line wrench or socket to remove the old chemical syringe from the pump. Make sure that the spring and ball are removed from it and not left in the pump manifold. Install the O-ring and the inside, use a tool to install the O-ring into the internal groove of the injector..
  • Package List: 1 × chemical injector + 1 × inlet check valve + 4 × mounting bolts + 4 × mounting o-rings, please compare with your old high pressure washer manifold kit when you buy, and then buy it..
  • Customer Service: You will get 24-months service, hassle-free return and money back policy, buy with confidence! If you have any questions, please contact us by email, we will reply you within 12 hours..
Check Stock

Raincovo Chemical Injector Kit, Soap Injector for Pressure Washer, 1/8 Inch 27 Male BSP Thread

  • Chemical injector kit fits most pump which is an OEM brand. Replaces pump 203640GS 308452002, 190593GS and 190635GS..
  • Soap injector makes cleaning so much easier and faster. It’s a great replacement for the old rusted one..
  • The brass fitting is a 1/8 inch 27 male BSP thread. Install them and the soap dispenser works just like new..
  • How to install: Take the brass fitting, drop in the little ball, insert spring with small end against the ball, then attach it back on the pump. Do not over-tighten otherwise it will snap off..
  • Kit includes 2 pieces fittings, 2 pieces small balls, 2 pieces springs, 2 pieces o-rings outside and 4 pieces inside..
Check Stock

Raincovo Downstream Injector for Pressure Washer Power Washer Chemical Injector Kit Soap Injector 3/8 Inch Quick Connect 4000 PSI

  • Package: Kit Includes chemical injector, 10 feet siphon hose, filter, black nozzle soap with 1/4” quick connect and teflon tape..
  • Application: When detergent is sucked out separately, the chemical will not pass through the pump, you could use a variety of chemicals without....
  • Characteristic: Chemical injector kit with a metering valve, which can adjust dilution ratio of soap and water. Avoid clogging of the injector and....
  • Connector: Downstream Injector has 3/8 inch quick connect. Fits most electric and gas power washer..
  • Material: Siphon hose is made of high-quality PVC, used for hot and cold water. Adapter is made of brass and stainless steel. Max pressure is 4000....
Check Stock

Meat Injector Kit, Plastic Marinade Turkey BBQ 1-oz Syringe with 2 Stainless Steel Needles - 3 Extra O-Rings & 1 Cleaning Brush For Basting & Grilling

  • FOOD SAFE BBQ INJECTOR – Syringe barrel, handle and pump plate of this food injector made of BPA Free & Eco-friendly premium quality plastic material. While the needles and plunger rod are made of food grade stainless steel. It is safe for marinating/cooking and durable to serve for years..
  • ENRICHES THE TASTE OF TOUGH/THICK CUTS - Different size needles cover almost all of your marinade meat injector needs. The special designed needles for deep penetration and perfect sauce distribution either its liquid, thick or chunky throughout the meat so you can enjoy the juicy, yummy and saucy barbecue or Cajun brines till its last bite!.
  • MULTI-PURPOSE BBQ INJECTION KIT - Sharp Injecting needles of this bbq injector kit punctures any meat or poultry with ease, flavor your meat in seconds and penetrates deep to deliver optimum flavor throughout. This turkey injector is used for infusing flavor of meat, chicken, turkey, beef, goose, duck, lamb, briskets but also to inject hot chocolate, butter, cream or jelly into donuts or to sweeten your dessert..
  • FRIENDLY TO USE - Ergonomic handle of this flavor injector allows a comfortable grip and friendly pressure control. It is easy and quick to assemble. Easy to clean. Just wash in a sink or throw into dishwasher..
Check Stock

JIFETOR Fuel Injection Pump Pressure Test Gauge Set, Automotive Gas Gasoline Fuel Oil Injector Tester Tool Kit 0-140PSI, with Schrader Adapters Universal Compatible with Ford Auto Car Truck Motorcycle

  • FUEL PRESSURE GAUGE TESTER: Automotive fuel injector tester tests if the fuel supply & injection system work normally, help to judge if there are broken internal components or faulty oil lines. Specific tool for fuel system detecting and troubleshooting. Fuel pressure gauge kit suits a variety of gasoline engines on car, truck, SUV, Motorcycle, ATV, RV, etc (Bosch, CIS Jetronic, Throttle Body System on GM vehicles excluded), not for diesel high pressure injection pump or direct-injection engine.
  • UPGRADED FUEL PRESSURE GAUGE TOOL KIT: The set is equipped with various fittings and hoses to connect for testing. 15"L hose is used for hooking up directly to the 1/4" SAE standard Schrader valve on fuel pump, 5-1/2"L hose for small Schrader valve (compatible with some Ford), and 8"L hose for M6 fuel pressure test port, and there are also M8/M10/M12/M14 adapters for the corresponding test port on fuel rail. The aluminum tee can splice in-line between the fuel pump and engine for most vehicles.
  • 140PSI/10BAR PRECISION-MACHINED FUEL PUMP TESTER GAUGE: You just need to ensure there is an adapter in the kit suitable for your test port or the inline connection is workable for your car. Pressure gauge adopts rubber cover protected 3-1/2" large dial and dual color cod....
Check Stock

6.0 POWERSTROKE KC STAGE 2 TURBO (04-07)

  • ◭ [Vehicle Application] : Injector Pressure Regulator Valve with Socket 6.0L Powerstroke Diesel Engines Fits for Ford 6.0L V8 Diesel Turbocharged Vehicles - for 2004-2010 Ford E-350 E-450, for 2003-2010 Ford Excursion, for 2003-2010 Ford F-250 F-350 F-450 F-550 Super Duty..
  • ◭ [Manufacturer Part Number] : Direct replace factory part AP63417 1846057C1 5C3Z9C968CA 5C34-9C968-CA W3250216 CM5126 and HTV102 for a proper fit, Include IPR Valve Seal Kit OE Number 3C3Z9H529A, AP0035.
  • ◭ [Function] : Precisely manufactured internal valves high quality diaphragms and springs to perform excellently under all engine operating conditions. Replaces Injector Pressure Regulator Valve and regulates the oil bypass circuit of the high pressure oil pump, that opens and closes to allow high pressure oil into the injectors.This enables the PCM to control fuel delivery by increasing the speed in which the IPR valve operates thus properly control the pressure in the high-pressure oil system..
  • ◭ [Material and Installation] : IPR Injector Pressure Regulator Valve, contructed of premium material for long lasting durability and reliability. Robu....
Check Stock

AEM (30-3302) V2 Water/Methanol Injection Kit with Internal MAP Sensor

  • Boost Dependent controller features on-board MAP sensor with large adjustment knobs, integrated plug for harness connection, integrated fuse, covered status light and test button for enhanced splash resistance and mounting tabs.
  • Wiring harness is terminated with a positive-lock connector on one end with color-coded wires to ease installation, power and ground wires for the pump and additional wire for optional on/off fluid solenoid.
  • Pump does not cycle on/off and provides quiet, smooth operation.
  • it features robust construction including integral hose fittings, EPDM seals and a Santoprene diaphragm that provides consistent and reliable fluid delivery.
  • Precision-machined billet-aluminum injector with integral check valve.
  • three interchangeable injector nozzles to cover a wide variety of HP levels (250cc/min, 500cc/min and 1,000cc/min).
  • tank-less 35 PSI Boost dependent gas water/methanol system.
Check Stock