Reviews Incra Miter Sled

INCRA MITER3000SE Miter Gauge with 27-Inch-49-Inch Telescoping Fence & Flip Shop Stop

  • Continuing its well respected tradition of "making accuracy easy".
  • This model features INCRA's exclusive AngleLOCK Indexed Positioning that locks in miter fence angles.
  • Features INCRA's Incremental "Flip" ShopStop Positioner.
  • 364 laser cut V-stops for extreme accuracy at all angles.
  • Patented GlideLOCK Miter Bar with 8 expansion points.
Check Stock

Rockler Clamp-It Corner Clamp Jig - Glass-Filled Polycarbonate Woodworking Clamps - Corner Clamps to Hold Panel Parts Together - Right Angle Clamp for Fastening Work - Woodworking Tools

  • Table Saw Miter Sled: This is the perfect table saw sled, no adjustments needed! Simply cut one piece on the leading face, one on the trailing face, and voila! Since both pieces reference off a perfect 90-degree angle, the miters will fit perfectly..
  • 45 Degree Miter Sled: This table saw sled system gives you an exact 45-degree cut every time. Our table saw miter is great for picture frames or anytime accurate corner. Miters cuts are needed..
  • Adjusting Miter Track Fit: Use a 7/64" hex wrench (not included) to advance the nylon set screws in the Rockler 45 degree miter sled bar until you achieve a smooth, no-slop fit in your saw’s miter track..
  • Standard Slot: Through slots in the base allow you to securely clamp moldings at table level. This table saw miter sled fits standard 3/8" x 3/4" miter slots..
  • Easy To Use: The table saw accessories miter can be easily drilled to add extended fences and stops. Pre-installed adjustable nylon pins provide a no-slop fit to the miter track..
Check Stock

Rockler 45 Degree Miter Sled for Table Saw - Miter Saw Sled Ensures Durability & Low-Friction Sliding - Table Saw Accessories Fits Standard 3/8\ x 3/4\ Miter Slot – Fence Accessories

  • Table Saw Miter Sled: This is the perfect table saw sled, no adjustments needed! Simply cut one piece on the leading face, one on the trailing face, and voila! Since both pieces reference off a perfect 90-degree angle, the miters will fit perfectly..
  • 45 Degree Miter Sled: This table saw sled system gives you an exact 45-degree cut every time. Our table saw miter is great for picture frames or anytime accurate corner. Miters cuts are needed..
  • Adjusting Miter Track Fit: Use a 7/64" hex wrench (not included) to advance the nylon set screws in the Rockler 45 degree miter sled bar until you achieve a smooth, no-slop fit in your saw’s miter track..
  • Standard Slot: Through slots in the base allow you to securely clamp moldings at table level. This table saw miter sled fits standard 3/8" x 3/4" miter slots..
  • Easy To Use: The table saw accessories miter can be easily drilled to add extended fences and stops. Pre-installed adjustable nylon pins provide a no-slop fit to the miter track..
Check Stock

INCRA MITER5000 Miter 5000 Table Saw Miter Gauge with Sled and Telescoping Fence

  • Capitalizing on a great idea, the folks at Incra.
  • The sled with T-track and clamping fixture secures the work piece as one solid unit for precision cross-cutting at any angle.
  • The right-hand portion of the sled, once cut.
  • Table saw that blends incremental angle control and a special 3-panel sled.
  • Precision angle indexing teeth are laser cut in solid steel.
Check Stock

INCRA MITEREXPRESS Miter Express

  • If you own a miter gauge - any miter gauge.
  • This sled is a sliding, miter-cutting platform that fully supports and controls your work piece throughout the cut.
  • Miter gauges drag your board across the table, a sled slides the work piece giving more support and control creating better, more consistent cuts.
Check Stock

SWAG Off Road Incra V27 Miter Gauge

  • The INCRA V27 miter gauge is made in the USA, and build to last as long as our tables..
  • The V27 features four adjustable expansion joints to eliminate any side play in the miter track..
  • The V27 also features their AngleLOCK indexing for quick tool free angle adjustment..
Check Stock

18” Precision Steel Miter Bar Rail Runner with Adjustable Spring Loaded Plungers For DIY Table Saw Crosscut Sleds, Jigs and Fixtures to Slide in 3/4 inch by 3/8 inch Miter Slots

  • Build your next table saw sled, router table jig or band saw fixture to operate with a smooth sliding action using the Fulton 18 inch Precision Steel Miter Bar! Attach the steel bar to most any type of sled, jig or fixture that is to be used with a 3/4 inch (19mm) by 3/8 inch (9mm) miter slot. Using our steel bar versus plastic or aluminum gives your sled, jig or fixture more strength and stability and it won’t bend or warp..
  • When building sleds, jigs and fixtures one of the most important aspects is to achieve a smooth sliding action without side to side play. The Fulton Precision Steel Miter Bar does both with its solid steel bar and 4 adjustable spring loaded plungers. The plungers can be adjusted with the included hex key wrench for just the right fit..
  • Not only is the Fulton Steel Miter Bar adjustable, its easy to mount! You can mount the bar from the top of your sled, jig or fixture platform or base, or you can mount it from the bottom. There are three threaded holes along the length of the bar for mounting the bar using 1/4 inch by 20 tpi machine screws (not included). There are also three counter sunk holes on the bar to mount the bar using #8 wood screws (not included)..
  • Once you mount the bars to your sled, jig or fixture you are sure to fee....
Check Stock

Miter T-Bar for Jigs Fixtures Sleds Router Tables and General Woodworking 48 inch MADE IN THE USA

  • When building sleds, jigs or fixtures for your woodworking projects that help keep your fixtures from moving or to help your sleds and jigs slide through a track, the Miter T Bar may just be the perfect solution. The Miter T Bar does this bit fitting neatly into most standard miter slots that measure ¾” x 3/8”. The aluminum bar can be used to slide your sleds or it can be used to lock fixtures like featherboards (when cut into smaller length pieces) in place in a miter slot..
  • The T-bar is made in the USA from a solid piece of extruded aluminum and can be cut into sections and drilled as needed. Typical uses for the T-bar are fixtures like featherboards where the featherboard needs to be kept stationary to apply consistent pressure. The T-bar also works great for sleds and other sliding fixtures like cutoff sleds on a table saw or coping sleds on a router table..
  • When mounting the Miter T-Bar it is a good idea to keep in mind that the “T” on the bottom of the track is approx. 1/8” tall, which is just enough to clear the t-slot on most miter slots. If mounted directly to platform for a sled, the tabs may catch and prevent the sled from sliding freely. To remedy this, we recommend using washers between the mounted track and the platform to....
Check Stock

WEN 3962T 3.5-Amp 10-Inch Two-Speed Band Saw with Stand and Worklight

  • CNC laser out of 3/16″ thick steel plate, formed on a CNC press brake..
  • Dual Miter Gauge slides, with optional foot swtich and Incra V27 Miter Gauge.
  • Fits the following models Milwaukee 6232-20, 6232-21, 6238-20, 6238-21& BS125.
  • Fits the following models Milwaukee Fuel M18 2729-20, 2729-21, 2729-22 & CBS125.
Check Stock

Rockler Table Saw Small Parts Sled

  • Sled base and fence provide zero-clearance support—just run it through your saw to locate the kerf.
  • Sled rides in miter track of your table saw—included miter slot stop limits forward travel of sled.
  • Rear-mounted blade guard is adjustable to fit most table saws.
  • Aluminum T-track on top edge of fence lets you add a flip stop (not included) for repeatable cuts.
  • Short T-track parallel to blade accepts an optional T-track hold-down clamp (sold separately).
Check Stock

INCRA MITER1000SE Miter Gauge Special Edition With Telescoping Fence and Dual Flip Shop Stop

  • Engraved stainless steel primary scale for precision accuracy.
  • 41 laser cut V-stops for extreme accuracy at all popular angles.
  • Patented GlideLOCK miter bar with 6 expansion points for quick repeats.
  • 18- to 31-inch telescoping incremental miter fence for handling a variety of stock widths.
  • INCRA Flip Shop Stop-Fence Positioner for optimal mitering accuracy.
Check Stock

Flattening Workbenches and Wide Boards with a Router

  • ...n blowout at the back of your end grain cuts. Also included is an abrasive strip that is adhered to the adjustable fence. The abrasive strip keeps your stock from sliding or wandering during the coping process. That, along with the heavy duty hold down toggle keeps your stock firmly in place..
  • Many sleds rely on the miter slot for reference. Our coping sled uses the fence as a reference instead. The Rail Guide Coping Sled Pro features a clear acrylic fence for reference which is offset and raised 2” above the base so you won’t cut into the sled. Using a fence rather than a miter bar mounted to the bottom means that you will always be parallel to the router table fence. This is a distinct time saving advantage as you will no longer have keep re-adjusting your router table fence.
  • This robust, full featured coping sled has a laminated ½” thick MDF base that slides across your router table surface effortlessly. The sled also features a large, heavy duty hold down toggle with a 1-5/8” hold down foot to keep your stock in place. The unit also includes two large and sturdy handles for guiding the sled through the cutter. The maximum stock size is 5” wide by 1 ¼” thick. Full instructions are included..
Check Stock

3-1/2\ To 4-1/2\ Universal Fence Clamp 2 Pack

  • Our 525 Large Coping Sled works on both the router and shaper, either in the miter slot or against the fence. This is the safest and most accurate way to make cope cuts and other cross-cuts on a router table or shaper. Don't try to cope without it! Two adjustable feed handles provide firm control over the sled and your work..
  • Includes an 11-3/4" adjustable steel miter bar that mounts in 6 different locations for best placement. Can also be used without the miter bar against your fence..
  • Holds stock up to 10" wide. Heavy duty 1/2" phenolic base (15-3/4" x 15-3/4") will not distort from clamp pressure..
  • Features one 500 lb. Outboard Toggle Clamp and two 500 lb. Inboard Toggle Clamps. Hold stock up to 1-3/4" thick, or 2-3/4" with optional 6305R Riser Kit (one Riser Kit required for each toggle clamp). Fence is 24” long. Optional 525S Flip Stop available for repetitive work..
  • Lifetime guarantee against defects in material or workmanship. Made in the USA!.
Check Stock