Reviews Humidity Sensor I2c

KEYESTUDIO Starter Kit V2 for Arduino with RJ11 Connector, Great STEM Education Kit for Students, Teachers and Hardware Enthusiast

  • Whenever you and your family go for vacations, you may used to get worried about your plants because they need water on regular basis. We develop this Automatic Plant Watering System to solve this problem as plants need water according to the moisture level of soil..
  • The kit includes a plus controller, DHT22 temperature and humidity sensor, I2C LCD, push button modules, power amplifier module, DS3231 clock module, non-contact level liquid sensor, motor driver module, capacitive soil humidity sensor, and pump..
  • More than 13 well-selected electronic modules and 17 step by step creative tutorials. Full example code is provided and explained and even includes useful software tool..
  • Multi-purpose: timing watering mode, and the sensor detection mode that when the soil is dry, Arduino will command the water pump to run(up to 4 plants at once)..
  • Our system measures the soil moisture and waters automatically according to it. A audio power amplifier module tells us when the bucket is empty. I2C LCD displays the temperature and humidity..
Check Stock

ACEIRMC 4pcs Si7021 GY-21 SHT21 HTU21 Digital Humidity Temperature Sensor Module Replace SHT11 SHT15

  • The humidity and temperature sensor board that carries a digital SHT21 humidity and temperature sensor from Sensirion..
  • Si7021 GY-21 Module Industrial High Precision Humidity Sensor I2C IIC Interface Module For Arduino Low Power CMOS IC Module.
  • It has a 4-pin interface that can communicate directly with the analog pins.
  • It can be used as a hardware- and software-compatible drop-in upgrade for existing RH/temperature sensors in 3x3 mm DFN-6 packages, featuring precision sensing over a wider range and lower power consumption..
  • The Si7021 offers an accurate, low-power, factory-calibrated digital solution ideal for measuring humidity, dew-point, and temperature, in applications ranging from HVAC/R and asset tracking to industrial and consumer platforms..
Check Stock

AITRIP 5pcs AHT10 High Precision Digital Temperature and Humidity Sensor Measurement Module I2C Communication Replace DHT11 SHT20 AM2302

  • AHT10 High Precision Digital Temperature and Humidity Sensor Measurement Module I2C Communication.
  • The sensor outputs a calibrated digital signal in standard I 2C format..
  • The AHT10 is equipped with a newly designed ASIC-specific chip,an improved MEMS semiconductor capacitive humidity sensing element and a standard on-chip temperature sensing element..
  • The AHT10,a new generation of temperature and humidity sensors,sets a new standard in size and intelligence:.
  • Its performance has been greatly improved beyond the reliability level of previous generation sensors. The first generation of temperature and humidity sensors have been improved to make them more stable in harsh environments..
  • it is embedded in a dual-row flat leadless SMD package reflow soldering with a 4 x 5mm bottom and a height of 1.6mm..
Check Stock

SHT31 Temperature & SHT31-D Humidity Sensor Module Breakout Weather for Arduino

  • The ESP8266 Weather Station IoT Starter Kit includes an ESP8266 ESP-12E Development Board, a 0.96" OLED display, a DHT11 Temperature and Humidity....
  • Developer-friendly module ESP8266 come with a USB connector and the maximum number of available pins. ESP8266 full IO mouth leads directly download....
  • The 0.96" 128x64 pixel OLED display supports I2C, wide viewing angle, low power consumption and high response speed.
  • DHT11 Temperature and Humidity Sensor with characteristics humidity measurement range: 20~90% RH, humidity measurement accuracy: +/-5% RH, temperature....
  • Four Projects in One – The ESP8266 and Wireless IoT development lets you 4 home projects, including weather station, plane spotter, world clock and....
Check Stock

ACEIRMC VL6180 VL6180X Range Finder Optical Ranging Light Sensor Module Gesture Recognition Sensor I2C Interface 3.3V 5V Emitter Ambient Light Sensor for Arduino I2C (4)

  • VL6180 VL6180X Range Finder Optical Ranging Sensor Module Gesture Recognition Sensor.
  • VL6180 is a time-of-flight ranging sensor. The sensor contains a very small laser source and a matching sensor..
  • I2C interface for device control and data, two programmable GPIOs..
  • VL6180X can detect the "time of flight" or the time required for the laser to recover the sensor to calculate the distance..
  • VL6180 VL6180X Range Finder Optical Ranging Sensor Module for Arduino I2C Interface 3.3V 5V gesture recognition.
Check Stock

Obstacle Avoidance Sensor TCRT5000 IR Infrared Reflective Sensor Line Detect Tracking for Arduino Robot Smart Car (Pack of 10)

  • APDS-9960 APDS9960 RGB Gesture Sensor Module.
Check Stock

4Pcs INA219 I2C Bi-Directional DC Current Power Supply Sensor Breakout Board Module I2C IIC Interface

  • INA219 module is an I2C interface with a drift, bi-directional current / power monitor integrated circuit (IC), and further expand the energy-saving....
  • INA219 I2C Bi-directional DC Current Power Supply Sensor, Working Voltage 3~5V.
  • INA219 module small size, low cost, high accuracy. It not only can monitor the voltage drop across a shunt resistor on the sensing shunt supply....
  • INA219 can be achieved within the maximum error accuracy of +1% from -40° C to 85° C temperature range, the maximum offset is 100 uV. The....
  • Appliaction:The module is used for I2C port zero drift / bidirectional current / power monitoring sensor module. The device is available in a SOT23....
Check Stock

Songhe 5MM LDR Photosensitive Sensor Module Light Dependent Resistor Sensor Module Digital Light Detection LM393 3 pins for Arduino (10PCS)

  • The BH1750FVI sensor to measure the ambient light level. BH1750FVI is a calibrated digital light sensor IC that measures the intensity of incident light and converts it to a 16-bit digital number..
  • It can measure the ambient light intensity ranging from 0 to 65535 lux (L). Lux is an SI unit for illuminance and is equal to one lumen per square meter. The BH1750FVI sensor directly gives the output in Lux..
  • The sensor's spectral response function is approximately similar to that of the human eye. The sensor output can be accessed via an I2C interface. The 7-bit I2C address is 0 × 23 if the ADDR pin is grounded, or if the 0x5C ADDR is bound to VCC..
Check Stock

ACEIRMC 3pcs IIC I2C TWI Serial LCD 2004 20x4 Display Screen Blue + IIC I2C Module Interface Adapter for Raspberry Pi Arduino (Blue)

  • The LCD has always been a device that acts as a window in human-computer interaction. For example, the prompt window on some instrument devices, the temperature and humidity prompt box, the device running status monitor, and the prompt screen of the counting device all have LCD figures.
  • LCD2004+I2C 2004 20x4 2004A Blue/Green screen HD44780 Character LCD /w IIC/I2C Serial Interface Adapter Module for arduino.
  • It is a high-performance serial bus with bus rules and high-speed or low-speed device synchronization required for multi-master systems. The I2C bus has only two bidirectional signal lines, a serial data line (SDA) and a serial clock line (SCL)..
  • Compatible with all devices with I2C interfaces, such as for Arduino, raspberry pi, beagle bone black, tinker board, stm32, esp32 and more..
  • please check which chip you have on i2c interface. (Before you upload the code to the control board, please download the LiquidCrystal_I2C library).
Check Stock

SparkFun Digital Temperature Sensor - TMP102 (Qwiic)-Compatible with Arduino and other Single-board computers Easy-to-Use I2C sensor Plug-and-Play breakout board Runs from 1.4-3.6V input Use with 3.3V

  • Uses the I2C interface. I2C Address: 0x48 by default (Three additional addresses available, as well). 12-bit, 0.0625°C resolution. Typical temperature accuracy of ±0.5°C.
  • 3.3V sensor. Supports up to four TMP102 sensors on the I2C bus at a time. 2x Qwiic Connectors.
  • The breakout has built-in 4.7kΩ pull-up resistors for I2C communications and runs from 1.4V to 3.6V..
  • I2C communication uses an open drain signaling, so there is no need to use level shifting..
  • The alert pin is an over temperature alert, which has an open-drain and is pulled up through a 10kΩ resistor. The alert can also be read over I2C.
Check Stock

AITRIP 5 pcs CJMCU-219 INA219 I2C Interface Bidirectional DC Current/Power Monitoring Sensor Module for Arduino Raspberry Pi

  • The INA219 achieves a maximum error accuracy of 1% over the -40 ° C to + 85 ° C temperature range with a maximum offset of 100 uV..
  • Used for I2C port zero drift / bidirectional current / power monitoring sensor module.
  • INA219 I2C Bi-directional DC Current Power Supply Sensor.
Check Stock

GY-521 MPU-6050 MPU6050 Module, 3 Axis Accelerometer 6 DOF Gyroscope Sensor Module Kit 16 Bit Converter Data Output IIC 3-5v Compatible with Arduino (10 Pieces)

  • GY-521 MPU-6050 module: integrates 3-axis gyroscope and 3-axis accelerator, including the hardware accelerator engine for devices connected to the second I2C port, like another accelerator of other brands, magnetometer, or Digital Motion Processor (DMP) of other sensors.
  • Parameter range: the MPU-6050's angular velocity range is ±250, ±500, ±1000 and ±2000°/sec (dps) for accurate fast and slow motion, and user-programmable accelerator full-frame sensing the range is ±2g, ±4g±8g and ±16g.
  • Transmission can pass I2C up to 400kHz or SPI up to 20MHz.
  • Chip built-in: with three 16-bit analog-to-digital converters (ADCs) for digitizing the gyroscope outputs and another three ones for digitizing the accelerometer outputs.
  • Easy to use: the measured values of the sensor can be interrogated by the I2C interface.
  • The accelerometer can be operated at both 3.3V and 5V.
  • Compatible with Arduino and Raspberry Pi.
  • Universal usable: the sensor can be applied to develop various entertaining applications and systems.
  • Nice for projects with gaming and virtual reality devices, navigation (for drones and RC planes) and DIY robots.
Check Stock

6pcs GY-521 MPU-6050 MPU6050 Module 3 Axis Accelerometer Gyroscope Sensor Module 6 DOF MPU-6050 16Bit AD Converter Data Output IIC I2C DIY Kit for Arduino

  • 【GY-521 MPU-6050 Module】Integrates 3-axis gyroscope and 3-axis accelerator, including the hardware accelerator engine for devices connected to the second I2C port.
  • 【Built-in Chip】With three 16-bit analog-to-digital converters (ADCs) for digitizing the gyroscope outputs and another three ones for digitizing the accelerometer outputs..
  • 【Easy to use】The measured values of the sensor can be interrogated by the I2C interface. The accelerometer can be operated at both 3.3V and 5V. Suitable for Arduino and Raspberry Pi..
  • 【User-programmable Gyroscope】With a full-scale range of ±250, ±500, ±1000, and ±2000°/sec (dps) and a user-programmable accelerometer with a full-scale range of ±2g, ±4g, ±8g, and ±16g Supports the I2C serial interface and has a separate VLOGIC reference pin..
  • 【Universal Usable】The sensor can be used to develop various entertaining applications and systems. Ideal for projects with gaming and virtual reality devices, GPS navigation (for drones and RC planes) and DIY robots..
Check Stock