Reviews Fulton Precision Miter Gauge

Fulton Precision Miter Gauge with Aluminum Miter Fence with 45 degree Angled Ends for Maximum Stock Support and a Repetitive Cut Flip Stop

  • ...g the length on the bottom of the slot. The steel miter bar is equipped with a metal, removable retaining disc that measures 7/8” in diameter and is just shy of 1/8” to fit into to the “T” slot to prevent accidental lifting when feeding your stock through..
  • Made from a single piece of extruded aluminum, this precision miter gauge fence is not only durable, its accurate and saves setup time. The fence is designed to be used with most any miter gauge with its off-set mounting track on the back of the fence. The off-set track allows you to flip the fence for lower profile miter gauge mounts and flip back for standard height miter gauges. The fence can be mounted to older miter gauges by adding a wooden block mount with wooden screws if necessary..
  • Both ends of the fence are cut at exactly 45 degrees. This allows you to position the fence extra close to the saw blade (with the power turned off) so you have even more control over the workpiece you are cutting. The fence comes with a flip stop that makes repetitive cuts a breeze. When not in use the flip stop can be flipped up and out of the way. Also include are two sticky back measuring tapes. 1 tape is left to right reading and the other is right to left reading..
Check Stock

Fulton Universal Aluminum Miter Gauge Fence with an Aluminum Flip Stop 18” Left Reading Tape 18” Right Reading Tape

  • ...uded are pretty good at this, we have also included a handy flip stop that locks into any location along the length of the fence. This allows you to make repetitive length cuts without worrying if the pieces will end up the same. The flip stop can can simply be flipped it up and out of your way when not in use..
  • The Fulton Aluminum Miter Fence is made from one, solid piece of extruded aluminum and has the exact same size track on the top of the fence as there is on the bottom. On the back, there is an offset track for mounting the fence to a miter gauge..
  • The fence can be mounted to low profile miter gauges or standard profile miter gauges simply by flipping the fence over to accommodate your miter gauge. This fence will fit most available after market and factory table saw miter gauges, however some modification may be required. Full color installation instructions are included..
Check Stock

Fulton Precision Miter Gauge with a Standard Slot (3/4” x 3/8”) Steel Bar with Adjustable Spring Loaded Plungers and Removable Retaining Disc

  • If you own a table saw and you need to make a crosscut at any angle then you know how valuable a miter gauge can be. You may also know that the miter gauge that came with your saw is not terribly accurate or durable. Not to mention that the fit in the miter slot may not be all that great as well. The Fulton Miter Gauge is a high quality, well thought out and economical solution to your table saw cross cutting needs..
  • The .200” thick, adjustable, solid aluminum head is machined with 13 positive stop holes. 1 hole is at 90 degrees while the 6 holes on both sides are at 22.5, 30, 45, 60, 67.5 and 90 degrees. The positive stops are perfect for many woodworking projects as they are the angles that are typically used..
  • To adjust the head you simply loosen the post knob handle, pull the spring loaded indexing pin outward, rotate the head to the desired position, release the pin and lock into place by tightening the post knob handle. The aluminum head has two ¼” x ½” slots milled into it for mounting a miter fence if so desired. The slots are approximately 1-1/8” from the base of the miter gauge head..
  • The head is mounted to a solid steel miter bar that measure 18” in length and is .354” thick by .730” wide. Standard miter slots are 3/4” x 3/8....
Check Stock

POWERTEC 71143 Deluxe Miter Gauge for Table Saw | Miter Guide with 120 Angle Stops

  • Function: a high performance woodworking angle tool that possesses a miter guide which mounts into the miter slots of your table saw (band saws and other applications) and then guides the miter gauge parallel to the blade for high precision angled and crosscuts.
  • Features: a lightweight design with a durable laser-cut aluminum construction, Large gauge handle, universal fence mounting bracket pivoting locking mechanism, A removal plate that allows the miter gauge to be used with t-slotted and non t-slotted miter slots, and adjustable Expansion discs that remove all side play from the bar, creating a perfect fit.
  • Precision: angle guide (with 120 total angle stops) in 5 degree increments over a full 180-degree range, and allows for plus or minus 60-degree range miter cuts.
  • Universal design:suited for most standard miter slots (3/4” width x 3/8” depth) with or without T-slots, making it compatible with popular Brand table saws, band saws, Router tables, disk and belt sanders.
Check Stock

POWERTEC 71142 Universal Table Saw Miter Gauge Assembly/Miter Gauge with 27 Angle Stops

  • FUNCTION: A high performance woodworking angle tool that possesses a miter guide which mounts into the miter slots of your table saw (band saws and other applications) and then guides the miter gauge parallel to the blade for high precision angled and crosscuts.
  • FEATURES: A lightweight design with a durable laser-cut aluminum construction, large gauge handle, universal fence mounting bracket, pivoting locking mechanism, a removal plate that allows the miter gauge to be used with T-slotted and non T-slotted miter slots, and adjustable expansion discs that remove all side play from the bar, creating a perfect fit..
  • PRECISION: Angle guide with 27 total locking stops in 5 degree increments over a full 180-degree range, and allows for plus or minus 60-degree range miter cuts.
  • UNIVERSAL DESIGN: Works with most Contractor style, full sized saws, or tools with standard miter slots (3/4” width x 3/8” depth) with or without T-slots, making it compatible with popular brand table saws, band saws, router tables, disk and belt sanders. PLEASE NOTE : will not work with smaller saws or tool with 5/8” miter slots..
Check Stock

Fulton Spring Clamp Pliers with 13 Spring Clamps and Hip Clip Made in the USA

  • ...p mitered corners then you know what kind of a challenge it can be to say the least. You could always try those large, cumbersome and very expensive parallel clamps to try and work each corner just right to hold your mitered corners together. That too can be extremely challenging and not to mention very costly..
  • The Fulton Miter Spring Clamps are the ideal and cost effective way to quickly and easily clamp mitered corners without all of the hassle you typically have with other clamps. The Spring Miter Clamps are made from a high strength steel. The clamps can be applied using your hand to squeeze the clamp to open the sharp, pointed tips or you can use the Miter Spring Pliers to make it super easy to to spread the tips apart..
  • Once you have the clamp tips spread apart, simply place the spring clamp onto the mitered corner you need to secure, then release the clamp so the tips pierce into the wood and keep your stock in place. Depending on the size of your project, you may need to use more than one spring clamp on each corner to hold your stock in place..
  • Unlike other available spring clamps, the Fulton Miter Spring Clamps don’t cut into your stock piece. The uniquely designed tips are designed to pierce the wood so that there is minimal visible eviden....
Check Stock

POWERTEC 71391 Table Saw Precision Miter Gauge System 24” x 3” Multi –Track Fence with 27 Angle Stops

  • Includes: (1) table saw miter gauge, (1) multi-track miter fence, (1) t-track flip stop.
  • Function: cost effective 3-piece set designed to give you everything you need to produce higher precision cuts (including cross cutting) while quick and accurate project results.
  • High precision miter gauge: features 27 angle indexing stops with 1-degree step spacing and positive stops at 0°, 10°, 22½°, 30° and 45° and nine others, both left and right.
  • Multi-track miter fence: smooth, laser engraved scale, extruded aluminum profile with a universal design that accepts accept 1/4"-20 hex Bots, 1/4” t-bolts and 5/16” T- bolts.
  • Miter saw flip stop: delivers exceptional cut-length control, with a convenient locking mechanism and an adjustable setting to work from left or right.
Check Stock

DCT Table Saw Fence and Miter Gauge for Table Saw with 3/8in x 3/4in Miter Saw Fence Bar – Table Saw Gauge 18 Inch

  • MAKE ACCURATE CUTS: The DCT | Table Saw Miter Fence with Miter Bar Gauge & Flip Stop offers safety and accuracy when cutting or sanding precise,....
  • USE YOUR TABLE SAW: 3/4-inch (19mm) miter gauge groove fits most standard 3/4-inch table saw slots (measure slot on your table saw to ensure exact....
  • NO MORE PLAY: 18-inch (45.7cm) long fence bar has 8-inch (20.3cm) usable length after fence starts.
  • Bar is 3/8-inch (9.5mm) thick x 3/4-inch (19mm)....
  • BUILT TO LAST: Flip stop slides effortlessly along the fence and locks in place with the plastic tightening knob for quick adjustment while the flip....
  • PACKAGE CONTENTS: Table saw accessories package includes (1) table saw precision miter gauge, (1) fence, (1) flip stop, and necessary saw miter gauge....
Check Stock

UOKRR Precision Miter Gauge for Table Saw Craftsman Telescoping 20" to 36" Aluminum Miter Fence Repetitive Cut Flip Stop 60° Angled Ends for Maximum Stock Support

  • Precision Angle Cutting: Accurate out of the box, this miter gauge and fence is easily adjusted to operate on either side of your sawblade. Its angles are very precise and got angle holes for 90, 60, 45, 30, 22.5 and 10 degree angle cuts, it will help you achieve square cuts and cut at an angle..
  • Well Constructed: This miter gauge is made of integrated aluminum alloy protractor with laser engraved scale and 9mm thicken plate, it's not easy to deform and with the features of 0.001 inch / 0.02mm high-accuracy. 20" to 36" Telescoping aluminum miter fence with striking metric and imperial scale design will more convenient for your operation, come with a aluminum flip stop for repetitive angled cuts on your table saw..
  • Compatible Standard Slot: The length of the miter bar is 19.68", and its slid smooth and perfect fit the guide rail for your table saw, the miter gauge fits standard miter slots are 3/4” x 3/8” with a 1/8” “T” slot, and it can be installed on most table saws..
  • Tool Free Installation: The miter gauge is very easy to setup and locking by manually turning the knob, made of premium aluminum alloy with its surface treated by CNC-machined anodic oxidation, which has higher wear resistance, the surface has been deburred and smoothed, no nee....
Check Stock

Rockler Retrofit Double Featherboard Kit

  • APPLICATION: Ideal for holding your workpiece in place (against the fence or table top) while cutting for router table and drill press applications, while safely keeping your fingers out of harms way from bits and blades.
  • PREMIUM DESIGN: Made with highly durable polymer, this featherboard set allows you to apply steady, heavy duty pressure for high precision cutting results while reducing kickback and problematic movement.
  • EASY TO INSTALL: 5-star threaded knobs and a standard 3/8” x ¾” miter gauge slot bracket allows you to set up your feather boards quickly and easily to any miter slot. Also includes 5/16”-18 t-bolts for t-slot or t-track applications.
  • VERSATILITY: For band saws, router tables and/or any woodworking machine with a standard 3/8” x ¾” miter gauge slot – double stacked and locked in both the horizontal and vertical position.
Check Stock

POWERTEC 71553 Table Saw Fence Featherboard – 2 Pack

  • APPLICATION: Ideal for holding your workpiece in place (against the fence or table top) while cutting for router table and drill press applications, while safely keeping your fingers out of harms way from bits and blades.
  • PREMIUM DESIGN: Made with highly durable polymer, this featherboard set allows you to apply steady, heavy duty pressure for high precision cutting results while reducing kickback and problematic movement.
  • EASY TO INSTALL: 5-star threaded knobs and a standard 3/8” x ¾” miter gauge slot bracket allows you to set up your feather boards quickly and easily to any miter slot. Also includes 5/16”-18 t-bolts for t-slot or t-track applications.
  • VERSATILITY: For band saws, router tables and/or any woodworking machine with a standard 3/8” x ¾” miter gauge slot – double stacked and locked in both the horizontal and vertical position.
Check Stock

Fulton Taper Cutting Jig For Creating Tapered Angles Up to 15 Degrees on Your Table Saw 24 Inch Long Aluminum Rails with Scale and Stop

  • Table saws are designed to rip stock parallel to the fence or cross-cut stock at various angles with a miter gauge. Making long rip cuts at angles from 1 deg to 15 degrees on a table saw without a jig can be challenging and dangerous attempting free hand..
  • The Fulton Taper Cutting Jig has been designed to make long rip cuts at angles from 1 deg to 15 degrees using your table saw. Perfect for building woodworking projects like table legs, chair legs, magazine racks and more where slight tapers are common..
  • Our taper jig will most certainly enhance your woodworking abilities and your woodworking projects. This easy to use jig is fully adjustable for right or left hand use. As well as its ability to work on either the left or right side of your table saw fence..
  • Two ways to set the jig. First use the scale that has markings up to 15 degrees of taper. Second mark the starting cut at one end and then mark the exit cut at the other end of your piece of stock. Then simply adjust the taper jig to match those two marks..
  • Constructed of durable aluminum the Fulton Taper Cutting Jig comes with an easy grip handle, adjustable 24 inch rails with fixed stop, easy-to-read graduated scale that measures 0 to 15 degrees of taper (or 3 inches per foot) and full instru....
Check Stock

POWERTEC 71156 Aluminum T-Track 48 Inch Combo with Aluminum Miter T-Bar

  • FUNCTION: The POWERTEC Miter track and bar set is designed to help build an assortment of sliding jigs and fixtures, while enhancing overall bench top table tool precision and functionality. They can be used together or separately, the miter track works with standard ¾” x3/8” miter bars and the T-bar fits standard ¾” x3/8” t-slotted miter slots..
  • APPLICATIONS: Ideal for benchtop table saws, router tables, band saws, and other woodworking shop projects that require a versatile set of miter track channels.
  • DESIGN: Both anodized aluminum extrusions possess a heavy duty construction, and feature a center guide track perfect for drilling and project alignment - The miter t-bar slides seamlessly into the miter track or t-slot.
  • SIZE SPECIFICATIONS: T-track works with ¾” x 3/8” miter gauges, with or without t-slot plate.
  • t- bars fit perfectly into t-slotted miter gauge slots - The 48" length can be custom cut to suit your individual project requirements.
Check Stock