Reviews Ford Focus Clutch Bleeding Tool

Dual Clutch Transmission Remover Installer Tool Compatible with Ford Focus, DCT Dual Clutch Transmission Reinstall Reset Tool Set for Reuse DCT F1FZ-7B546-B, Clutch Transmission Tools Accessories

  • 【Dual Clutch Transmission Tool with Good Compatibility】The dual clutch transmission remover installer tool is made of heavy-duty steel, which is corrosion-resistant and high in hardness. Perfectly compatible with Ford Focus DCT dual-clutch transmission DPS6..
  • 【Professional Dual Clutch Transmission Tool】Reuse the removed/previously installed dual-clutch assembly. It resprings/re-trips the springs on the clutch so that the user can reinstall it..
  • 【Durable Dual Clutch Transmission Tool】The surface of the dual-clutch transmission remover installer tool is specially phosphated, which not only prevents rust, but also has a longer service life. With this tool, you will not need to purchase any new DCT clutch components..
  • 【How to Use the Dual Clutch Transmission Tool】Install the special tool and press the input shaft tightly. After the threaded bar is in contact with the input shaft, it rotates 20 times..
  • 【All-In-One DCT Tool Set】The dual-clutch transmission tool is equipped with a toolbox, which is very convenient for product organization and storage. If you have any q....
Check Stock

43300 Pneumatic Fan Clutch Wrench Set Removal Tool Kit Gear Assisted Positioning Tool for Ford GM Chrysler by Lucky Seven

  • 43300 Pneumatic Fan Clutch Wrench includes 7 driving wrenches that fit Ford, GM, Chrysler & Jeep. Set now includes 7/8", 32mm, 36mm, 40mm thin and new 47mm size to fit Ford 6. 0L and 6. 4L Power stroke diesel pickup. 1-7/8"and 2" are still included in the set. 1-1/2" 41mm and 42mm are still available individually..
  • 43300 Pneumatic Fan Clutch Wrench Set ，Package included:1 * 43370 handle+1 *43380 32mm driving wrench+1 *43390 36mm driving wrench+1 *43440 40mm driving wrench+1 *43530 47mm driving wrench+1 *43430 7/8" driving wrench+1 *43410 1-7/8" driving wrench+1 *43420 2" driving wrench.
  • 43300 Pneumatic Fan Clutch Wrench Kit,43300 pneumatic fan clutch,Fan clutch installer/remover set,Quickly removes and installs fan clutch when repairing the water pump or fan clutch.Faster and easier than conventional fan clutch wrenches. No holding wrench is necessary..
  • 43300 Pneumatic Fan Clutch Wrench AKA Fan clutch removal tool kit,43300 pneumatic fan clutch wrench set,for 43300 lisle,43300 wrench set,43300 fan clutch tool,43300 pneumatic fan clutch,for lisle 43300 pneumatic fan clutch wrench set,....
Check Stock

DPTOOL Dual Clutch Transmission DSG Remover Installer Tool Kit Compatible with Ford DPS6 Dual Clutch Reinstall Reset Tool

  • Removal Install Dual Clutch: Special designed to disassembly and install dry transmission. Disassemble the double clutch fixing snap ring, install and remove the three claws, turn the threaded bar 20 turns after it makes contact with the input shaft and pull out the double clutch.
  • Reinstall Reset Dual Clutch: this tool could resprings/re-trips the springs on the clutch so that you can Disassembly lock and installing an unlock.
  • Applicable: compatible with ford dual clutch transmission DPS6. vehicle include: Fiesta 2011-2019.
  • 12 Months Warranty: we offer 12 months warranty, we will refund or replace if the product have any quality problem.
Check Stock

Lisle 14440 Water Pump Wrench

  • More extensive design: 32mm&36mm clutch fan removal tool kit, compatible with a wider range of models than similar products, compatible with most models of BMW, Ford and Mercedes-Benz. And its price is more affordable and better quality. This is a two-piece multifunctional tool that you will like..
  • Application: 32mm&36mm wrench tool is compatible with BMW M4 M10 M20 M30 M40 M44 M50 M52 M52TU M54 M56 M60 M70 M73 S14 S38 S54 S50B30 S50B32 and newer models, compatible with Ford..
  • Brand new upgrade tool: 32mm & 36mm Fan Clutch Nut Wrench tool is more practical than similar tools on the market. It has passed rigorous engine tests and is fully fitted, which can save you a lot of money.
  • Quality: This 2-piece fan clutch wrench set is made of high-strength steel, with precise dimensions, and has undergone many actual vehicle tests. The rubber handle covered in the middle helps prevent hand fatigue during prolonged use..
  • Service: ZKTOOL has the most perfect warranty service. We provide all the necessary information for each product. If you have any questions, please contact us. We will wait 24 hours..
Check Stock

SR Performance Clutch Alignment Tool; 10 Spline

  • OTC's 10-Spline Truck Clutch Alignment Tool is designed for use when installing heavy-duty single, two-plate, push/pull, manual, and self-adjusting clutches.
  • Tool is constructed of lightweight fiberglass-reinforced nylon that won't hang up in clutch disc splines.
  • Rugged construction will easily support the weight of heavy clutch discs.
  • To use, loosely install clutch disc and pressure plate on flywheel then insert alignment tool through the clutch into the bearing, center disc, then tighten pressure plate to spec.
  • 1-3/4 inch O.D. shaft, 1 inch pilot, 10 splines.
Check Stock

Prokomon 8PCS Pneumatic Fan Clutch Wrench, 43300 Fan Clutch Removal Tool Kit for Ford, GM, Chrysler and Jeep

  • ◇ Durable --- The wrench tool kit is made of sturdy steel, durable and strong, with strong resistance to corrosion and rust..
  • ◇ Specifications --- Fan clutch wrench 7/8", 32 mm, 36 mm, 40 mm, 47 mm, 1-7/8" and 2". Wrench tool for Ford 6.0L and 6.4L power-stroke diesel pickups.
  • ◇ Easy to Use --- Simply slide the tool into the air hammer to select the correct wrench size for the fan nut, give it a few taps with the air hammer, and the fan clutch will loosen. No need for any other special nailing tools. (Note: Air hammer not included).
  • ◇ Function --- Specially designed to help you easily disassemble and install the fan clutch when repairing the water pump or fan clutch. (Please confirm the size you need before purchase).
  • ◇ Applications --- Compatible for Ford, Chrysler, GM and Jeep.
  • Compatible for 4.3L, 5.0L, 5.7L GM pick up (van, mini-van, or SUV)..
Check Stock

Phoenix Systems (2005-B) Bench Brake Bleeder Kit, One Person Bleeder, Fits All Makes and Models

  • Patented Reverse Bleeding removes more trapped air than any other brake bleeder by simply pushing Brake Fluid fluid from the bottom up..
  • Reverse bleeding is the only method capable of bleeding tough ABS units without a scan tool..
  • Allows you to refill and bench bleed a completely dry brake or clutch system. Perform Reverse, Vacuum, Pressure and Bench bleeding all with the same tool..
  • The Bench Bleeder is considered a Medium Duty tool for average shop use. Compatible with DOT 3, 4 and 5.1 brake fluid..
  • Is the easiest one-person bleeder you will ever use. No more asking your co-worker to help you finish a brake job..
Check Stock

ABN Air Compressor Clutch Rebuild Removal Tool Kit AC Clutch Puller for Car Auto Air Conditioning on GM, Ford, Chrysler

  • REPLACe A/C CLUTCH ASSEMBLY: Use the ABN Air Compressor Clutch Rebuild Removal Tool Kit – AC Clutch Puller for Car Auto Air Conditioning to remove, install, or rebuild clutches found on FS6, C171, 6P, and 148 compressors.
  • GM R4 and A6, HR-6, DA-6 and V A/C compressors.
  • sander compressors SD 505, 507, 575, 708, and 709.
  • Wide application of vehicles including GM, Ford, Chrysler, imports, and other makes and models.
  • Check vehicle owner’s manual for a list of compatible compressors.
  • EASY TO USE: Keep all threads clean and well-oiled.
  • Outer part of tool has smooth side and threaded side (threads used to attach to inner clutch shaft when removing).
  • Start with one bearing between tool and clutch, and thread down fully onto compressor's inner shaft threads (This is the fixed part - inner bolt does not move when threading down outer piece).
  • Remove tool and stack other bearing on to take up the distance the clutch pushed into pulley.
  • BUILT TO LAST: Constructed from stainless steel with a black coated finish for ultimate strength and longevity.
  • Resists rust and corrosion with proper care and lubrication.
  • 2 and 3 hold puller plate allows mechanical force to do all of the pulling on most clutches.
  • EASY STORAGE: Heavy-duty 10.5” x 8.25” x 2.25” inch (2....
Check Stock

Dorman 14505 Clutch Alignment Tool Compatible with Select Models

  • OTC's 10-Spline Truck Clutch Alignment Tool is designed for use when installing heavy-duty single, two-plate, push/pull, manual, and self-adjusting clutches.
  • Tool is constructed of lightweight fiberglass-reinforced nylon that won't hang up in clutch disc splines.
  • Rugged construction will easily support the weight of heavy clutch discs.
  • To use, loosely install clutch disc and pressure plate on flywheel then insert alignment tool through the clutch into the bearing, center disc, then tighten pressure plate to spec.
  • 2 inch O.D. shaft, 1-1/4 inch pilot, 10 splines, splines are 3.6 inches long.
Check Stock

NexADD Fan Clutch Wrench Set 32mm & 36mm Water Pump Holder Tool Fit for BMW Ford GM Chevrolet,Fan Clutch Nut Wrench Set,Fan Clutch Removal Tool,Water Pump Pulley Holder,Clutch Fan Removal Tool Kit

  • REMOVE & REINSTALL AUTOMOTIVE FAN CLUTCHES ★- The NexADD 32mm & 36mm Fan Clutch Wrench Kit with Fan Pulley Holding Tool removes lock nuts on temperature-dependent thermo-viscous fans. The holder bar keeps the water pump pulley in place while loosening the radiator fan. It is a direct replacement and completely fit, wich could help you save much money..
  • FITS YOUR VEHICLE★-The NexADD Fan Clutch Wrench Set is compatible with BMW vehicles, including, but not limited to,the following applications: fan clutch wrench tool is kit compatible with BMW M4 M10 M20 M30 M40 M44 M50 M52 M52TU M54 M56 M60 M70 M73 S14 S38 S54 S50B30 S50B32 and compatible with Ford.Also compatible with some Ford, GM, and Chevy models..
  • BUILT TO LAST★- The 15" fan clutch wrench and holder are specially lengthened to provide extra leverage with sure grip when working on hard-to-get-to fan clutch nuts on metric thermo-viscous fans, letting you service your timing or water pump quickly and easily. The rubber handle covered in the middle helps prevent hand fatigue during prolonged us..
  • EASY TO USE ★- Attach the pulley holder bar with your bolts inserted through the holes, lock into place on water pump face, place wrench on fan clutch nut, and loosen the fan clutch nut by turning clock....
Check Stock

Phoenix Systems (2003-B) V-12 Reverse Brake & Clutch Bleeder Kit, Medium Duty One Person Bleeder, Hard Case

  • Patented Reverse Bleeding removes more trapped air than any other brake bleeder by simply pushing Brake Fluid fluid from the bottom up..
  • Reverse bleeding is the only method capable of bleeding tough ABS units without a scan tool..
  • Allows you to refill and bleed a completely dry brake or clutch system. Perform Reverse, Vacuum, Pressure and Bench bleeding all with the same tool..
  • The V-12 is considered a Medium Duty tool for average shop use. Compatible with DOT 3, 4 and 5.1 brake fluid. Comes with a injection molded hard case..
  • Is the easiest one-person bleeder you will ever use. No more asking your co-worker to help you finish a brake job..
Check Stock

ClutchXperts SPC Clutch Alignment Tool KIT Compatible With 2006-2015 Mazda MX-5 Miata 2.0L 6-Speed

  • OTC's 10-Spline Truck Clutch Alignment Tool is designed for use when installing heavy-duty single, two-plate, push/pull, manual, and self-adjusting clutches.
  • Tool is constructed of lightweight fiberglass-reinforced nylon that won't hang up in clutch disc splines.
  • Rugged construction will easily support the weight of heavy clutch discs.
  • To use, loosely install clutch disc and pressure plate on flywheel then insert alignment tool through the clutch into the bearing, center disc, then tighten pressure plate to spec.
  • 2 inch O.D. shaft, 1-1/4 inch pilot, 10 splines, splines are 7.3 inches long.
Check Stock

Mekar Pneumatic Fan Clutch Wrench Set Clutch Removal Tool Kit Compatible with Jeep, Ford, GM,Chrysler

  • 【Fitment】: Compatible with Ford, GM, Chrysler and Jeep vehicles (Kindly note: please make sure the size you need before purchase).---Product quality has been upgraded, please rest assured to buy. Support one-year warranty..
  • 【High Quality Material】: Made of 1/4" thick steel, durable and high strength, Corrosion and rust resistance..
  • 【7 Driving Wrenches Sizes】: 7/8", 32mm, 36mm, 40mm, 47mm, 1-7/8" and 2" (the slim new 47mm wrench tool is suitable for Ford 6.0L and 6.4L Powerstroke diesel pickup trucks), comes with a Storage bag, which is easy to store and carry..
  • 【Function】: When servicing the water pump or fan clutch, our special tool can easily remove and install the fan clutch. You can install it around the clutch and release the clutch by quickly pulling the trigger, and finally releasing it (Kindly noted: use with an air hammer)..
  • 【Package Included】: 7*Wrenches + 1*Storage bag. ------Guarantee: Any problem about the product, please feel free to contact us. Support one-year warranty and return service.(Including return and refund service).
Check Stock