Reviews Flatbed Hubs And Spindles

Yukon Gear & Axle (YA WU-04) Spin Free Locking Hub Conversion Kit for Dodge SRW Dana 60 AAM Differential

  • "locking hub conversion kit for '00-'08 dodge dana 60 and 9.25"" front, single rear wheel design".
  • the yukon worry free spin free kit replaces the vulnerable and expensive factory unit bearings with tapered bearings and races.
  • the result is not only a design which is easier and more economical to service, but one that offers significant increases in mileage per gallon.
  • this hub kit also includes low-profile yukon hardcore premium locking hubs, giving you more driving selectability.
  • this kit includes new wheel hubs, spindles, high strength yukon 4340 chrome-moly outer axles, yukon hardcore premium locking hubs, timken bearings, high quality seals and all hardware for installation.
Check Stock

JDMSPEED 2 Trailer Idler Hub Kits 5 on 4.5 Replacement for Axle 1-1/16 Bearings 2000 lbs - 22016K

  • Set of 2 New trailer idler hub kits 5 on 4.5 for 2,000 lbs trailer axle, for 1-1/16" straight spindle.
  • Kits also include: 4x L44649 outer cone bearings, 2x Grease seals 1-1/16", 2x E Z lube grease caps with rubber plug.
  • Bolt pattern: 5 on 4.5", bearing races and 1/2"-20 studs installed.
  • Note: This hub fit straight spindles, not for tapered spindles.
Check Stock

RIGID HITCH INCORPORATED Pair of 5-Bolt On 4-1/2 Inch Hub Assembly AKRD-2200545 Includes 2 1-1/16 Inch Straight Spindles & Bearings

  • Pair of 1-1/16" straight spindles includes castle nuts and cotter pins..
  • Bearings included - (4) L-44649 1-1/16" inside dimension..
  • Hubs have pre-installed pressed in races..
  • Hub has a 5-bolt pattern on 4-1/2" bolt circle. Pilot diameter 2-1/2", flange diameter 5.56" and measures 4-1/4" tall (through center of hub).
  • Spindles feature a ROUND 1-1/4" stock diameter with a bearing surface of 1-1/16 inch..
Check Stock

RIGID HITCH INCORPORATED Pair of 5-Bolt On 4-1/2 Inch Hub Assembly AKSQ-2200545 Includes 2 Square Shaft 1-1/16 Inch Straight Spindles & Bearings

  • Pair of 1-1/16" straight spindles includes castle nuts and cotter pins..
  • Bearings included - (4) L-44649 1-1/16" inside dimension..
  • Hubs have pre-installed pressed in races..
  • Hub has a 5-bolt pattern on 4-1/2" bolt circle. Pilot diameter 2-1/2", flange diameter 5.56" and measures 4-1/4" tall (through center of hub).
  • Spindles feature a 1-1/2" SQUARE stock diameter with a bearing surface of 1-1/16 inch..
Check Stock

The ROP Shop Trailer Axle Kit Assembly with 4 on 4" Bolt Idler Hub & 1" Round BT8 Spindle

  • Replacement Trailer Axle Kit Assembly with 4 on 4" Bolt Idler Hub & 1" Round BT8 Spindle.
  • Specs - 1,250 lb Hub Capacity, Used On 2,000 lb Axle Shaft 1 Diameter: 1 1/4" Shaft 2 Diameter: 1" Shaft Length: 8 3/4" (4" Long Stub) Hub A Diameter.: 2 1/2" Hub B Diameter: 5 1/2" Bolt Pattern: 4". Refer to images 2 & 3 for more information.
  • Includes - (1) Idler Hub with Lug Nuts, (1) 1" BT8 Round Spindle with Castle Nut, Pin & Washer, (2) Inner/Outer Bearings, (1) Double-lip Grease Seal (1 1/4" I.D. / 2" O.D.), (1) 2" Grease/Dust Cap.
  • Assembly with 4 on 4" bolt idler hub & 1" round BT8 spindle. Rated to 1,250 lbs. each or 2,000 lbs. for the pair.
  • Fits 2,000 pound trailer axles with straight spindles, but to know if this hub is the right fit for your setup you would want to check the size your current bearings and make sure that they match up with the 1" bearings that these hubs come with as well as knowing that you have a standard length spindle. This Hub fits standard length spindles, not "short spindles".
Check Stock

The ROP Shop Pack of 4 Trailer Axle Kits with 4 on 4 Bolt Idler Hub & 1 Round BT8 Spindle

  • Replacement (Pack of 4) Trailer Axle Kits with 4 on 4" Bolt Idler Hub & 1" Round BT8 Spindle.
  • Specs - 1,250 lb Hub Capacity, Used On 2,000 lb Axle Shaft 1 Diameter: 1 1/4" Shaft 2 Diameter: 1" Shaft Length: 8 3/4" (4" Long Stub) Hub A Diameter.: 2 1/2" Hub B Diameter: 5 1/2" Bolt Pattern: 4". Refer to images 2 & 3 for more information.
  • Includes - (4) Idler Hub with Lug Nuts, (4) 1" BT8 Round Spindle with Castle Nut, Pin & Washer, (8) Inner/Outer Bearings, (4) Double-lip Grease Seal (1 1/4" I.D. / 2" O.D.), (4) 2" Grease/Dust Cap.
  • Assembly with 4 on 4" bolt idler hub & 1" round BT8 spindle. Rated to 1,250 lbs. each or 2,000 lbs. for the pair.
  • Fits 2,000 pound trailer axles with straight spindles, but to know if this hub is the right fit for your setup you would want to check the size your current bearings and make sure that they match up with the 1" bearings that these hubs come with as well as knowing that you have a standard length spindle. This Hub fits standard length spindles, not "short spindles".
Check Stock

The ROP Shop (Pack of 2) Trailer Axle Kits with 4 on 4" Bolt Idler Hub & 1" Round BT8 Spindle

  • Replacement (Pack of 2) Trailer Axle Kits with 4 on 4" Bolt Idler Hub & 1" Round BT8 Spindle.
  • Specs - 1,250 lb Hub Capacity, Used On 2,000 lb Axle Shaft 1 Diameter: 1 1/4" Shaft 2 Diameter: 1" Shaft Length: 8 3/4" (4" Long Stub) Hub A Diameter.: 2 1/2" Hub B Diameter: 5 1/2" Bolt Pattern: 4". Refer to images 2 & 3 for more information.
  • Includes - (2) Idler Hub with Lug Nuts, (2) 1" BT8 Round Spindle with Castle Nut, Pin & Washer, (4) Inner/Outer Bearings, (2) Double-lip Grease Seal (1 1/4" I.D. / 2" O.D.), (2) 2" Grease/Dust Cap.
  • Assembly with 4 on 4" bolt idler hub & 1" round BT8 spindle. Rated to 1,250 lbs. each or 2,000 lbs. for the pair.
  • Fits 2,000 pound trailer axles with straight spindles, but to know if this hub is the right fit for your setup you would want to check the size your current bearings and make sure that they match up with the 1" bearings that these hubs come with as well as knowing that you have a standard length spindle. This Hub fits standard length spindles, not "short spindles".
Check Stock

The ROP Shop (Pack of 8) Trailer Axle Kits with 4 on 4" Bolt Idler Hub & 1" Round BT8 Spindle

  • Replacement (Pack of 8) Trailer Axle Kits with 4 on 4" Bolt Idler Hub & 1" Round BT8 Spindle.
  • Specs - 1,250 lb Hub Capacity, Used On 2,000 lb Axle Shaft 1 Diameter: 1 1/4" Shaft 2 Diameter: 1" Shaft Length: 8 3/4" (4" Long Stub) Hub A Diameter.: 2 1/2" Hub B Diameter: 5 1/2" Bolt Pattern: 4". Refer to images 2 & 3 for more information.
  • Includes - (8) Idler Hub with Lug Nuts, (8) 1" BT8 Round Spindle with Castle Nut, Pin & Washer, (16) Inner/Outer Bearings, (8) Double-lip Grease Seal (1 1/4" I.D. / 2" O.D.), (8) 2" Grease/Dust Cap.
  • Assembly with 4 on 4" bolt idler hub & 1" round BT8 spindle. Rated to 1,250 lbs. each or 2,000 lbs. for the pair.
  • Fits 2,000 pound trailer axles with straight spindles, but to know if this hub is the right fit for your setup you would want to check the size your current bearings and make sure that they match up with the 1" bearings that these hubs come with as well as knowing that you have a standard length spindle. This Hub fits standard length spindles, not "short spindles".
Check Stock

Southwest Wheel R40842X 42 Spindle & 6-5.5\ Bolt Circle Trailer Hub

  • Pair of 1" straight spindles includes castle nuts and cotter pins..
  • Bearings included - (4) L-44643 1" inside dimension..
  • Hubs have pre-installed pressed in races..
  • Hub has a 4-bolt pattern on 4" bolt circle. Pilot diameter 2-1/2.
Check Stock

Southwest Wheel R20484X 84 Spindle & 5-4.5\ Bolt Circle Trailer Hub

  • Pair of 1-1/16" straight spindles includes castle nuts and cotter pins..
  • Bearings included - (4) L-44649 1-1/16" inside dimension.
  • Hubs have pre-installed pressed in races.
  • Hub has a 4-bolt pattern on 4" bolt circle. Pilot diameter 2-1/2.
Check Stock

Southwest Wheel R30484X 84 Spindle &5-4.5\ Bolt Circle Trailer Hub

  • Pair of 1-1/16" straight spindles includes castle nuts and cotter pins..
  • Bearings included - (4) L-44649 1-1/16" inside dimension..
  • Hubs have pre-installed pressed in races..
  • Hub has a 5-bolt pattern on 4-1/2" bolt circle. Pilot diameter 2-1/2.
Check Stock

Triton 02360 2200 Lb Snowmobile Trailer Torsion Axle

  • Adjustable spring mounts offer a variety of mounting positions.
  • Fast Lube spindles allow you to re-grease the bearings without removing the hubs.
  • Stainless steel wear sleeves prevent rust from wearing on the rubber oil seal.
  • 1.5in. square tube steel axle is hot dip galvanized with adjustable spring centers.
Check Stock

Southwest Wheel R30484X 84 Spindle & 5-5.5\ Bolt Circle Trailer Hub

  • Pair of 1-3/8" to 1-1/16" tapered spindles..
  • Bearings included - (2) L-68149 1-3/8" I.D & (2) L-44649 1-1/16" I.D.
  • Hubs have pre-installed pressed in races..
  • Hub has a 5-bolt pattern on 5" bolt circle. Pilot diameter 2.59.
Check Stock